Instructions
- Shut off the electricity. Unplug the power cord from the wall outlet. ...
- Remove the agitator. Pull the fabric softener dispenser off of the top of the agitator. ...
- Remove the agitator dogs. Pull the top auger off of the agitator assembly. ...
- Install the new agitator dogs. Push the new agitator dogs into the cam. ...
- Reinstall the agitator. ...
- Restore the power. ...
How do you replace the agitator dogs on a Kenmore washer?
Take off the plastic bearing that rests on top of the agitator dogs. Remove the agitator dogs from their holder and replace them with new ones. After the new agitator dogs are installed, place the plastic bearing back on the cam and put the cam back into the agitator.
How do you replace the agitator on a whirlpool washing machine?
Attach the top half and bottom half of the agitator. Once the two ends are secure, place the agitator assembly back in the washing machine and reinstall the bolt. Put the dust cap back in the agitator and snap on the assembly’s top cover.
How does an agitator dog work?
The agitator dogs’ job is to grip the teeth inside the agitator, which then causes the top section to create a one-way ratcheting motion. These are typically found in brands like Whirlpool, Maytag, Amana, and Kenmore. As we said earlier, a malfunctioning agitator is often caused by worn agitator dogs.
How do I know if my washing machine agitator dogs are bad?
If you are able to manually spin it in both directions, the agitator dogs are no longer functioning properly and will need to be replaced. If you have noticed your washing machine’s agitator is working to a much weaker degree, the agitator dogs could possibly be the issue.
How do you change an agitator on a dog?
3:039:45How to Repair Agitator Dogs On A Whirlpool Washing Machine.YouTubeStart of suggested clipEnd of suggested clipOkay once you got the agitator out of the machine just gently. Step on the bottom don't you knowMoreOkay once you got the agitator out of the machine just gently. Step on the bottom don't you know step harder.
How do you take the agitator out of a Kenmore washing machine?
0:061:13Whirlpool/Kenmore Top Load Washer Replace Agitator #W10076310YouTubeStart of suggested clipEnd of suggested clipTo replace your washers agitator first remove the fabric softener dispenser and lint cap ifMoreTo replace your washers agitator first remove the fabric softener dispenser and lint cap if applicable to your model. Then use a 7/16 inch socket with a 12 inch extension to loosen the mounting bolt.
How do I replace an 80040?
2:106:13How To: Whirlpool/KitchenAid/Maytag Agitator Dogs 80040 - YouTubeYouTubeStart of suggested clipEnd of suggested clipStand on the lower half of the agitator. And pull up on the upper half of the agitator. Once youMoreStand on the lower half of the agitator. And pull up on the upper half of the agitator. Once you have it off you can go ahead and dump it upside down get out your agitator bolt and your old cam. Set.
How do you remove the agitator from a Kenmore 70 series?
1:237:19Kenmore 70 series agitator repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo let's pull this up out of here long bolt. So my bolt is out i accidentally dropped it down inMoreSo let's pull this up out of here long bolt. So my bolt is out i accidentally dropped it down in there. But. This whole piece will just pull up off there. And then this just pulls out.
How do you change the agitator dog on a Kenmore 110 washer?
0:421:41How to Replace the Agitator Dogs on a Kenmore Vertical ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the fabric softener dispenser off of the top of the agitator. Pull the dust cap out of theMorePull the fabric softener dispenser off of the top of the agitator. Pull the dust cap out of the agitator. Use a 7/16 socket with an extension to remove the agitator bolt.
How do you remove a top loader agitator?
0:392:50How to Clean, Remove and Replace the Agitator in your Washing MachineYouTubeStart of suggested clipEnd of suggested clipAnd then write down the center of the agitator as a little wound yard remove that just hold theMoreAnd then write down the center of the agitator as a little wound yard remove that just hold the agitator as you unscrew anticlockwise.
How do you change an agitator dog washer?
0:421:41How to Replace the Agitator Dogs on a Whirlpool Vertical ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the fabric softener dispenser off of the top of the agitator. Pull the dust cap out of theMorePull the fabric softener dispenser off of the top of the agitator. Pull the dust cap out of the agitator. Use a 7/16 socket with an extension to remove the agitator bolt.
How do you install an agitator?
1:363:01Washer Repair- Replacing the Agitator (Whirlpool Part# 3951744)YouTubeStart of suggested clipEnd of suggested clipYou're going to put the bearing side down short centers in the opening. And there are four slots onMoreYou're going to put the bearing side down short centers in the opening. And there are four slots on that holder that will line up with the tabs on the agitator base slide that down line those up.
How do I know if my washing machine agitator is broken?
The agitator should start to oscillate back and forth, mixing up the clothes in the water. If the agitator does not move, double check that the sensor is depressed. If it still does not move with the sensor depressed, the agitator is broken and should be repaired.
How do I remove the agitator on my Kenmore 80 series?
0:3810:45How to fix Kenmore 80 series agitator - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe second thing is to remove this cap which if you have fingernails. And lifts right off if not youMoreThe second thing is to remove this cap which if you have fingernails. And lifts right off if not you can use a a flathead screwdriver to lift it right up.
How do you take apart a Kenmore washer model 110?
0:253:22Disassemble Whirlpool/Kenmore Direct Drive Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey have spring clips. They have to slip a putty knife underneath to release them. Once you haveMoreThey have spring clips. They have to slip a putty knife underneath to release them. Once you have your screws out slide the control panel forward about 1/2 an inch.
How do you remove a bolt from an agitator?
1:134:08How To: Whirlpool/KitchenAid/Maytag Agitator Bolt WPW10076270YouTubeStart of suggested clipEnd of suggested clipOnce you have the socket on the agitator you'll notice that it spins the whole tub. So you're gonnaMoreOnce you have the socket on the agitator you'll notice that it spins the whole tub. So you're gonna have to reach down and hold it while you break the bolt. Free.
How to remove agitator dogs from holder?
To do this, simply pull the two sections apart. Once the top and bottom sections are disconnected, turn the top half upside down. The cam, which holds the agitator dogs will fall out. Take off the plastic bearing that rests on top of the agitator dogs. Remove the agitator dogs from their holder and replace them with new ones.
What is an agitator dog?
Agitator dogs, which are also known as dog ears, ratchet cogs, or agitator cogs control what direction the top section of a dual action agitator moves in. Basically, the upper part of your washer’s agitator should only move in a single direction, while the lower portion has the ability to rotate in multiple directions.
Why is my agitator dog not working?
Symptoms The Agitator Dogs Are Failing. As we said earlier, a malfunctioning agitator is often caused by worn agitator dogs. Usually, the failure is simply due to normal wear and tear or old age, but overloading your washing machine on a regular basis can also speed up the deterioration of the part. The top section of your agitator should only spin ...
How to tell if agitator is working?
Taking the agitator apart is the only way to tell if this is truly the problem. The upper half of your machine’s agitator pulls the clothing to the bottom of your appliance tub. If the agitator is not working properly, due to failing agitator dogs, your clothes will remain at the top of the tub. Safety Warning: As with any washer repair, safety ...
How to repair a washing machine that is unplugged?
After you have unplugged your washing machine, open the lid and remove the top cover of the agitator. Reach into the agitator and take out the dust cap. With the dust cap removed, you should see a bolt in the middle of the agitator.
What is the agitator in a washing machine?
Simply put, that large cylinder, which is referred to as an agitator, circulates in multiple directions to push and pull the water in the machine. That rotation dispenses the laundry detergent, keeps the load from clumping up in the washer’s tub and removes the dirt from your clothes. Like any part of an appliance, the agitator can malfunction.
Can you spin an agitator in both directions?
The top section of your agitator should only spin in one direction. If you are able to manually spin it in both directions, the agitator dogs are no longer functioning properly and will need to be replaced.
