how do you change a water valve in a bathroom

1. Insert your new valve. Grip the end of the new valve cartridge (which should be identical to the old cartridge) with pliers and slide it back into its slot ...
2. Slide the metal clip back into place. Using your needlenose pliers, pick up the new valve's metal clip and insert it into place.
3. Turn on the water supply. If you tightened the water stops, loosen them by turning or screwing them to the right.
4. Put the trim plate and handle back in place. Set the trim plate back over the access hole and screw it in place on both sides.

Full Answer

How to repair water damage in a bathroom?

12 Tips for Water Damage Repair

• Know the Different Types of Water. Believe it or not, there are three types of water. The first type is "clean" water from rain, condensation, leaky pipes, and so on.
• Inspect for Serious Issues like Mold. Inspect damaged materials for mold and mildew. ...
• For Significant Damage, Check Your Insurance

How do I replace a toilet water supply valve?

Method 2 Method 2 of 3: Replacing a Threaded Valve

1. Remove the valve by turning it counter-clockwise. If you have a threaded valve, all you need to do is twist it off the supply pipe.
2. Inspect the exposed threaded supply line. With the old valve removed, check inside the pipe for rust or corrosion.
3. Replace the old Teflon thread tape. ...
4. Screw the new valve onto the threaded supply line. ...

More items...

How to shut off your water valve?

• Inside the house, the main water shut-off valve is usually located along the perimeter of the home on the side that faces the street. ...
• The valve may have a multi-turn handle similar to an outdoor hose faucet or a single lever control. ...
• Outside water meters are typically found along the curb and sidewalk of your home, within your property lines. ...

How to conserve water in the bathroom?

Conserve water in your bathroom by paying careful attention to the way you use your appliances.. Toilet. To begin, you can save gallons of water by flushing your toilet less often. Employ a new house rule to only flush when absolutely necessary and save up to 50 gallons of fresh water each week.

How do you replace a bathroom valve?

0:203:28HOW TO REPLACE A WATER SHUT-OFF VALVE - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can expect to drop while tackling the project this one is pretty simple easy step one is toMoreYou can expect to drop while tackling the project this one is pretty simple easy step one is to remove any junk in the area of the valve that you're going to be working on get it all out of the way.

How do I fix the water shut off valve in my bathroom?

1:526:30Toilet Water Shut Off Valve Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo free up some more room to work if it's easily accessible remove the other end of the water supplyMoreTo free up some more room to work if it's easily accessible remove the other end of the water supply hose by turning the nut counter. Clockwise. If the water supply hose hasn't been recently replaced.

Is it easy to replace a water valve?

A threaded valve screws directly onto the water supply line and is easy to replace. In a compression connection, the valve screws into a hexagonal nut that fits around the supply line. The most difficult type to replace is a sweat valve, which is soldered onto the supply pipe.

How do you remove a water valve from a toilet?

1:562:39How to Fix a Toilet - Water Supply Valve Replacement - Part 1 of 2YouTubeStart of suggested clipEnd of suggested clipRemove both lock nuts and turn the valve to the off position. So it is ready for quick installationMoreRemove both lock nuts and turn the valve to the off position. So it is ready for quick installation when the old valve is. Removed you.

How do you fix a leaking water shut-off valve?

First shut off the water to the leaking water valve. Next remove the handle from the stem and then loosen and remove the packing nut. Remove the old washer and slide on the new one. Reinstall the packing nut, tighten lightly with a wrench (don't over tighten at this or any other point) and reattach the handle.

How do you change a main water valve?

1:024:47How to Replace a Main Shutoff Valve | Ask This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay. So the water's off out on the street. And we've opened up the faucets in the house to drainMoreOkay. So the water's off out on the street. And we've opened up the faucets in the house to drain the water down. And now we've got to install our new shut off valve.

How much does it cost to change a water valve?

It typically costs between $375 and $600 to replace a water shut-off valve, but the cost can reach as high as $800 or more depending on where the valve is, what type you have, and whether you hire a professional to do it.

Why is water shut-off valve dripping?

Since cut-off (shut-off) valves are rarely used, the washer inside the valve can become hard or covered with mineral deposits over time. When you close the valve then open it again, the washer on the valve stem may not seat properly, causing it to leak around the valve stem nut.

How do you remove old valves?

2:258:08How To Remove/Install a LEAKY/NEW SHUT-OFF Valve ...YouTubeStart of suggested clipEnd of suggested clipThen you want to remove the valve by holding the body with one wrench and undoing the nut withMoreThen you want to remove the valve by holding the body with one wrench and undoing the nut with another.

How do I replace a water valve?

If your old valve is threaded, or screws directly onto the pipe, you can simply twist it off and replace it with a new valve. Other valves are secured to the pipe with a compression nut, which you can loosen and replace with a new compression fitting.

How to tighten a valve?

Thread the valve into the compression nut. Place the valve on the end of the pipe, then pull the compression nut down the pipe's shaft to the threaded end of the valve body. Rotate the nut clockwise by hand, then use a pipe wrench to finish tightening it .

How to remove a compression nut from a pipe?

With the compression nut loosened, simply pull the old valve off of the pipe. Locate the compression sleeve, which is a ring that fits snugly at the end of the pipe. Use pliers to carefully rotate it and remove it from the pipe, then slide off the compression nut. Don't use too much pressure with the pliers.

How to remove a threaded valve?

If you have a threaded valve, all you need to do is twist it off the supply pipe. Affix a pipe wrench to the flat sides where the valve body connects to the pipe. Rotate it counter-clockwise to loosen and remove it.

What to do when you turn off the water supply?

When you turned off the water supply at the start of the project, you turned on faucets to drain the system. Make sure the faucets are turned off, then turn on the water supply. Check the valve you replaced for leaks and turn on (or flush) any fixtures it feeds. Tighten the valve with the pipe wrench if it leaks.

How many flat sides does a threaded valve have?

A threaded valve will have 2 to 6 flat sides where it meets the supply line. These flat sides allow you to remove the valve with a pipe wrench. If you have a sweat valve, you'll be able to see where the valve body is soldered, or melted, into the water supply line.

Can you replace a sweat valve with a hacksaw?

Sweat valves, or the third type of connection, are soldered directly to the pipe, and they need to be cut with a hacksaw or torch. While replacing a valve is usually easy, it's wise to contact a professional plumber if you have old, rusted, or corroded pipes. Steps.

What is the valve on a bathroom sink?

The valves in most bathroom sink faucets have a similar construction in that they are all attached to the faucet handle. Every time the faucet handle is turned, the valve is rotated to either stop the flow of water or allow a stream of water through the spout.

Why replace a faucet valve?

This essentially because the bathroom sink fittings are prone to developing internal wear and tear due to the high degree of daily usage. This is best exemplified by bathroom fittings like faucets that are prone to neglectful handling.

How to unfasten a faucet handle?

You are most likely to find a main locking nut below the cap. Remove this nut with a wrench. This will help you to unfasten the handle of the faucet. The locking nut can be corroded and very hard to turn. You might need to tap it lightly with the screwdriver and apply some petroleum jelly to loosen it.

What is the packing nut on a valve?

You might need to hammer them lightly to knock off the corroded debris. The valve stem nut is also called the packing nut.

How to get water out of a faucet?

Start by wearing plastic gloves. Locate the main water supply valve that is usually located under the skin. Shut off the water supply. Move the faucet handle to ensure that the last drops of water are also drained out. If you cannot locate the main valve around the skin, turn off the main water-supply.

Can a bathroom sink valve be repaired?

It is generally recommended that bathroom sink valves shouldn’t be repaired since repaired valves are not likely to hold up for a very long period of time. It is always better to replace them. Replacing a bathroom sink valve is rather easy.

How to get water off of right of way?

Call the water utility company and have them shut the water off at the right of way. Be sure that the water is completely off before doing any work on your plumbing. If you are unsure if the water is completely off, please call a plumber. Removing a valve while the water is still ON at the right of way can lead to serious damage.

What is the top image of a gate valve?

The top image is a gate valve. These are installed in most older homes and will usually end up breaking or leaking at some point. The image on the bottom is a 1/4 turn ball valve. These are recommended over the traditional gate valve.

What to do if shower valve is damaged?

If your shower valve is damaged beyond repair, you may need to replace it to prevent leaks. Removing your old valve and installing a new one can take time, but with patience, a novice handyman can do it without the help of a plumber.

Can you reuse a valve clip?

If your valve clip is not damaged, you should be able to reuse it while securing the new cartridge in place . If it is, however, your new cartridge should come with its own valve clip. Some valve sets are secured with a retainer nut that holds them in place.