Can you change the oil in a Toro snowblower?
Any owner of a Toro Two-Stage Snowblower wants their machine to perform at a high level. That’s why knowing when and how to change the engine oil of your snow blower will help maintain its power, endurance, and dependability. Check out our tips for properly changing the engine oil of your Toro Two-Stage Snowblower.
Is it time to put your Toro snowblower to rest?
Once the winter is over, it’s time to finally put your Toro snowblower to rest. But before you put away your machine, there are plenty of things you can do to improve and maintain the maintenance of your snowblower, so it’s all ready to go next winter.
Do Tortoro snowblowers have shear pins?
Toro two-stage snowblowers do not use shear pins. The commercial-grade gear case makes the need for a shear pin unnecessary. If the auger hits an obstruction or is over-loaded with snow, the engine may shut off, so that you can remove the key, clear the obstruction safely with a stick and get back to work.
How to fix a snow blower that won’t turn on?
Try to turn the impeller with your pry bar to rotate the stuck pieces back out. Some of the parts on the snow blower might be rusted so have a good penetrating oil product on hand to help. Start by removing the auger belt covers. Some have bolts located on the top, some on the bottom, and some models have them on the top and the bottom.
How do you dismantle a snowblower?
0:184:31Ariens Snowblower Disassembly (Model #921022), Repair HelpYouTubeStart of suggested clipEnd of suggested clipNow use a half-inch socket to remove the bolts and washers securing the belt guide. And pull theMoreNow use a half-inch socket to remove the bolts and washers securing the belt guide. And pull the guide off remove the bolts and washers securing the blower housing to the frame.
How do you remove the auger from a Toro snowblower?
0:062:03Toro Snowblower Auger Blade Replacement 99-9313 - YouTubeYouTubeStart of suggested clipEnd of suggested clipLoosen the center bolt to fully release the old blade prepare the new auger blade for installationMoreLoosen the center bolt to fully release the old blade prepare the new auger blade for installation by transferring the middle hole bushings from the old blade to the new one.
How do you remove the carburetor on a Toro snowblower?
1:495:33Toro Snowblower Carburetor Replacement 127-9111 - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the housing off of the mounting bolts. Slide off the carburetor intake gasket attach a pinchMorePull the housing off of the mounting bolts. Slide off the carburetor intake gasket attach a pinch clamp to the fuel hose then release the fuel hose from the carburetor.
How do I remove the primer bulb from my Toro snowblower?
1:524:39How to Change the Primer Bulb on a Toro Single Stage SnowblowerYouTubeStart of suggested clipEnd of suggested clipSimply put them on those white tabs squeeze them in and then I can push the primer. Out like thatMoreSimply put them on those white tabs squeeze them in and then I can push the primer. Out like that the primer is made up of two pieces.
How do you remove the auger assembly from a snowblower?
0:204:48Craftsman Snowblower Auger Assembly Replacement #984-04393YouTubeStart of suggested clipEnd of suggested clipPush the idler pulley down to release the brake and pull off the auger pulley and belt.MorePush the idler pulley down to release the brake and pull off the auger pulley and belt.
How do I remove the auger shaft from my snowblower?
4:014:59How To Remove The Auger Assembly from a Murray SnowblowerYouTubeStart of suggested clipEnd of suggested clipIf you're going to do it that way make sure that the two bolts holding at the auger system at theMoreIf you're going to do it that way make sure that the two bolts holding at the auger system at the front of the blower that they're off now the next thing to take off is this collar.
How do you unclog a carburetor on a snowblower?
Snowblower Carburetor Cleaner Turn off the snowblower engine and leave it to cool. Remove the carburetor bowl, float bowl and flathead. Spray and clean the dirty carburetor with a carburetor cleaner, removing debris with a cloth. Let it sit to remove impurities.
Where is the carburetor located on a Toro snowblower?
2:546:51Toro snowblower won't start quick fix with GumBuster by CleanCarburetorYouTubeStart of suggested clipEnd of suggested clipIt will fit all four-stroke Toro snow blowers either single stage or dual stage so let's go to itMoreIt will fit all four-stroke Toro snow blowers either single stage or dual stage so let's go to it the carburetor and snow blower is located right underneath your choke.
Why does my Toro snowblower keeps stalling?
A clogged carburetor is most commonly caused by leaving fuel in the snowblower for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to stall.
How do you change a primer bulb?
3:585:26How to Replace a Primer Bulb - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust like that now the primer bulb is held in place by a couple of small tabs I find the easiest wayMoreJust like that now the primer bulb is held in place by a couple of small tabs I find the easiest way to remove it is to just use a pair of needle nose pliers and kind of press the tabs.
Where is the primer bulb on Toro lawn mower?
Primer Bulb – Located on the air filter cover, close to the carburetor which is located opposite the muffler.
How do you remove auger bearings?
0:566:39How to Replace Auger Bearings - YouTubeYouTubeStart of suggested clipEnd of suggested clipProcess you can use a long hook tool to pry it out usually this top bearing stays good for longerMoreProcess you can use a long hook tool to pry it out usually this top bearing stays good for longer because it is farther away from the heat.
What is a snowblower auger?
Augers - Rotating paddles or serrated metal blades. Single stage snow blowers use rubber paddles to collect and throw snow in one motion, while two stage models have metal serrated augers that cut through deeper snow to feed the impeller.
Step 1: Snow Blower Handle
Let’s start with the handle. Once you have this placed in its full upright position, be sure the bolts and washers are fitted correctly and tighten the handle knob securely. This is important because if the handle comes loose during operation you could strip the threads, making it hard and even unsafe to use your snow blower.
Step 2: Install the Discharge Chute
Ok, let’s install the discharge chute. This procedure may look a little different depending on the model you own, but the important thing is don’t over-tighten the screws or bolts that you used to attach the shoot to the machine. That could damage the shoot or keep it from turning freely.
Step 3: Adjust Control Cable
Here’s how to do it: With the engine shut off, move the control bar back toward the handle to remove the slack and the control cable. With the bar in this position, you should have a gap of 1/16th to 1/8th inches or 2 to 3 millimeters between the control bar and the handle.
Step 4: Engine Oil & Testing New Snow Blower
Ok, let’s move on. Build the engine with oil following the instructions in your manual or our changing the oil video. Remember to change your engine oil after the first two hours of operation. This is really important to flush out any dirt or particles that may accumulate in a new engine.
Fuel Tips for Gasoline Lawn Mowers and Snow Blowers
Wondering what type of gasoline to put in your lawn mower or snow blower?
How to Assemble a Toro Single-Stage Snowblower
Just purchased your first Toro Single-Stage Snowblower? Now all you need to do to get your machine up and running is some minor assembly. Don’t sweat it if this sounds intimidating. After watching this quick and easy video tutorial, you’ll be using your fully assembled Toro Single-Stage Snowblower in no time!
How to Assemble a Toro Two-Stage Snowblower
Can’t wait to get started testing out your new Toro Two-Stage Snowblower? After some quick assemblage, you’ll be able to experience pristine performance, power, and durability, unparalleled to any other snowblower on the market.
How to Choose the Right Snowblower
No matter what your snow removal needs are, Toro has the lineup of snowblowers that will help you make the best purchase possible.
Tips to Starting Your Snowblower
Prevent snow blower starting problems by following these great tips before the snow starts to fall. Follow these steps to help guarantee your snow blower will start.
End of Snow Season Snowblower Tips
Once the winter is over, it’s time to finally put your Toro snowblower to rest. But before you put away your machine, there are plenty of things you can do to improve and maintain the maintenance of your snowblower, so it’s all ready to go next winter.
Snowblower Winter Checklist - Single-Stage
Prepare your Toro single-stage snow blower for the winter with these essential maintenance tips. In this video, we'll review what signs of wear and tear to look out for on your rotor blades, proper oil changing and fuel requirements, and much more. Make sure you and your Toro snow blower will be ready for whatever this winter brings your way!
Warranty Service
For warranty repair or service consideration please visit an *Independent Authorized Service Dealer for a physical inspection of the machine and/or engine.
Engine Specific Warranty Service
Engine specific warranty service is provided through the original engine Manufacturer i.e. Briggs & Stratton, Kohler, or Kawasaki.
Step 1
Check the level in the fuel tank if the snowblower does not start, sputters or has trouble starting. If old fuel sat in the gas tank over the off season, drain it with a hand-pump siphon. Check your owner's manual to determine the oil-fuel ratio for your snowblower, as they vary with Toro models.
Step 2
Check the Toro's spark plug if it will not start. Remove the Toro's spark plug wire, remove it with a spark-plug wrench and examine it. If it is corroded or appears to be fouled, replace it with a new spark plug.
Step 3
Check the electric starter switch if the snowblower will not start. First inspect the rubber boot on the switch. If it is worn, it may allow water in, and should be replaced. Remove the switch's electrical connector by hand. Press the leads of the test light to each of the starter switch's leads. There should be no continuity.
Step 4
Check the drive belt if the snowblower runs but does not throw snow. If the belt is worn, stretched or broken it should be replaced. To do this, turn the ignition key to the off position. Remove the cap screw, located on top of the drive cover, with a screwdriver. Also remove the drive cover screws with a screwdriver and pull the drive cover off.
Who makes Toro snowblower engines?
Toro snowblower engines are made by a company called Loncin. They are manufactured to specifications laid out by Toro.
Are all Toro snowblower engines manufactured by Loncin?
While Toro may have used other companies to produce their snowblower engines in the past, all modern snowblower engines will be Loncin models.
Does Toro design their own snowblower engines?
While they do have some control over the tuning of their snowblower engines, the engines are designed by Loncin.
Where are Toro snowblower engines manufactured?
Toro snowblower engines are manufactured in China and then imported into the United States.
Are Toro snowblower engines good?
Yes. Toro snowblower engines are good. Toro are one of the leading producers of snowblowers in the world, and this is because they always try to ensure that the components (including the engine) that go into their products are as high quality as possible.
Do Toro snowblower engines use plastic components?
Yes. Like all snowblower engines, there will be plastic components in a Toro snowblower engine. However, there won’t be any in areas that will quickly wear down.
How do you know what Toro snowblower engine you have?
All of the details about the snowblower engine that you own can either be found in the manual that arrived with your snowblower, or check out the specification for the engine on the Toro website.
