The Pop-Up Drain Stopper
- Rotate the overflow faceplate or flip the lever to open the stopper.
- Pull straight up to remove the stopper. You may have to move it back and forth a bit.
- Some of these stoppers have a rocker arm that comes out with the stopper. ...
- Replace the stopper and plunger with a new one and make sure it is firmly sealed.
How do you remove a bathtub drain?
Remove the Drain Basket
- Once you have removed the drain stopper, you will see the drain basket (also known as a drain flange) in the drain opening. ...
- To remove the drain basket, you will need either locking pliers or a tub drain wrench. ...
- If you are using a drain wrench, insert the drain wrench into the drain and turn it counterclockwise to unscrew the drain basket.
How to remove the bathtub drain?
Remove the faceplate of a trip lever drain.
- The faceplate will be on the tub wall near the faucet, not on the bottom of the tub with the drain.
- These type of drains will stop a tub when a trip lever is activated. ...
- Set the tip of the screwdriver underneath the lip of the loosened drain if you need some leverage as you pull it out.
- Make sure to pull away from the tub wall.
How to remove bathtub push stopper?
- Move the rotating dial to the open setting.
- Gently remove the stopper from the drain opening and use wiggling movements to remove the whole arm linkage from the same opening.
- Wipe off any grime from the pop – up stopper and rocker arm. ...
- Restore some shine by polishing the stopper with commercial chrome polish. ...
How to remove tub plug?
This is how it works:
- Grab a washcloth or sponge, roll and squeeze it so that it is only slightly larger than the drain opening.
- Insert it in a small plastic bag and push out as much air as possible.
- Seal the plastic bag. ...
- Insert the cloth in the drain opening so that it is firmly held in place.
- Start filling the tub with water.
- Enjoy your bath.
How does a clevis work?
What is a pop up tub?
How to remove a sink stopper?
How does a pop up drain stopper work?
Why won't my sink pop up?
How to keep a drain stopper in good working order?
How to adjust pop up stopper?
See 2 more
How do you fix a push down plug?
0:284:10How Do I Fix a Stuck Push Down Sink Plug | 4 Ways To Free Pop Up PlugYouTubeStart of suggested clipEnd of suggested clipThere. So in my previous. Video i said put on a rubber glove. And just push. Down. As hard as youMoreThere. So in my previous. Video i said put on a rubber glove. And just push. Down. As hard as you can with the rubber glove. So you got grip. Turn counterclockwise. And it pops up see.
Why won't my pop-up drain pop-up?
There are a few reasons why this part of your sink might not be working. The part of the pivot rod that connects to the drain stopper may have rusted or broken off, or the drain stopper itself might be broken so that the pivot rod can't actually pull the stopper down.
How do you put a pop-up drain back together?
1:393:31How to Install a Pop-Up Drain in a Bathroom Sink | Repair and ReplaceYouTubeStart of suggested clipEnd of suggested clipFirst take a small amount of plumber's putty and roll it into a snake place the putty around theMoreFirst take a small amount of plumber's putty and roll it into a snake place the putty around the drain.
Why won't my pop-up plug stay down?
If the stopper moves as it should but doesn't stay put, all you need to do is tighten the nut (turn it clockwise). If the action is too stiff, loosen the nut a little. Check the action and adjust until it feels about right.
How do you replace a push pop-up drain stopper?
0:361:58How to Install Push Pop-Up Drain Plug Stopper and Review - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake a pair of pliers. And loosen the lock nut remove the p-trap to free up the tail pipe then goMoreTake a pair of pliers. And loosen the lock nut remove the p-trap to free up the tail pipe then go ahead and remove the old flange. You'll want to clean up the area of the drain hole in the sink.
How do you clear a pop-up drain?
How to Clean Your Pop-up Drain Stopper:Turn off the water, just in case. ... Disconnect the horizontal ball rod from the clevis. ... Take the horizontal ball rod out of the drain pipe. ... Remove the stopper, then ditch the mess. ... Soak everything in vinegar and scrub it clean. ... Put the stopper back in the sink drain.More items...
Can you use plumbers putty on pop-up drain?
Plumber's putty is a malleable, clay-like compound that creates a watertight seal by filling in the space under a flange to prevent water from seeping through. The product is ideal for setting faucets, sink basket strainers, shower and pop-up drains.
How does a pop-up drain assembly work?
0:081:38What Is A Pop Up Drain For A Bathroom Sink? - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn between the faucet handles that would pop it up and down these just simply push to open or pushMoreIn between the faucet handles that would pop it up and down these just simply push to open or push to close to stop the water. This here has capability for an overflow.
How does a pop-up drain plug work?
SO HOW DOES A SINK POP-UP MECHANISM WORK? It's actually a fairly simple design. When the lift rod is pulled upwards, it pulls the pivot rod up as well. This pivot rod is attached to the stopper, which is pulled down, effectively sealing the sink.
How do you adjust a pop up bathtub plug?
0:040:49HOW TO Adjust Your Bath Plug - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo lift the plug out. Notice there is little brass spline turnitin just finger tight it back up dropMoreSo lift the plug out. Notice there is little brass spline turnitin just finger tight it back up drop it back in. And you can see that's it.
How do you adjust a pop up stopper?
0:494:08Adjusting Your Bathroom Sink Stopper - YouTubeYouTubeStart of suggested clipEnd of suggested clipI usually move the stopper control rod all the way down which puts the stopper all the way up dropMoreI usually move the stopper control rod all the way down which puts the stopper all the way up drop that rod.
Do pop up plugs unscrew?
Pressing and turning the pop-up plug counter-clockwise can lift up the plug from the sink. Some types of pop-up plugs can be lifted up this way easily. Others will need extra steps to remove. The other type of pop up plugs need to be removed from under the sink.
How do I unblock a pop up box?
Manage pop-ups & redirects for a specific siteOn your computer, open Chrome .Go to a page where pop-ups are blocked.In the address bar, click Pop-up blocked .Click the link for the pop-up you want to see.To always see pop-ups for the site, select Always allow pop-ups and redirects from [site] Done.
How does the overflow work on a pop up drain?
As the water exits, it will create a suction that causes the bottle to contract unless air is allowed in. If you poked a hole in the bottle, air would be able to replace the liquid mass and the soda would drain smoothly and at a constant rate. In the same way, the over-flow drain helps your sink drain faster.
How does a pop up clicker drain work?
The "pop-up" waste operates the drainage plug by lifting a lever, which is located directly behind the faucet, up and down.
How A Pop-Up Stopper Works
Bathroom sink pop-ups are raised and lowered with a lift knob or lever, usually located on or near the faucet body. The knob or lever is connected...
How to Remove A Bathtub Stopper
It’s easy to remove a tub stopper to check it for mechanical problems or blockage. You’ll encounter a couple of different types of bathtub pop-ups:...
How to Fix A Sink Pop-Up Stopper
Water may leak or refuse to drain around a sink pop-up for a number of reasons. If your sink pop-up won’t pop up or seat properly, fixing it is qui...
How does a clevis work?
The flat, slotted clevis is connected by a small spring clip to a pivot rod–and–ball assembly—a rod that runs through a rubber pivot ball and slopes slightly upward to the tailpiece of the stopper. This rod pushes the stopper up or lets it drop down into the drain body.
What is a pop up tub?
A bathtub pop-up is a two-part mechanism: first, the stopper, which has a rocker arm that extends back toward the drain, and second, the overflow assembly, a lever that lifts or lowers a rod with a spring-like end.
How to remove a sink stopper?
If it seems to be linked to the mechanism below, reach under the sink and unscrew the pivot rod retaining nut and pull out the pivot rod to disengage it. Use locking-jaw pliers to loosen it if necessary.
How does a pop up drain stopper work?
Pop-ups are simple mechanical devices that use a system of links and levers to move a drain stoppers up and down to seal a sink bowl or bathtub. Bathroom sink pop-ups are raised and lowered with a lift knob or lever, usually located on or near the faucet body.
Why won't my sink pop up?
Water may leak or refuse to drain around a sink pop-up for a number of reasons. If your sink pop-up won’t pop up or seat properly, fixing it is quite easy—usually just a matter of adjusting a few parts. The culprit is often a buildup of hair around the base of the stopper or the pivot rod mechanism. Or, the clevis may be out of adjustment (see illustration to identify the various parts).
How to keep a drain stopper in good working order?
Keeping the drain clear of hair, soap and shampoo residue, and other debris is one of the best ways to help keep the stopper in good working order.
How to adjust pop up stopper?
Depending upon the type of pop-up, you adjust the way the stopper seats either by adjusting the length of the striker rod or by adjusting the rocker arm.
How to lower a stopper on a tub?
To lower the stopper, thread the bottom lock nut down. Next, spin the adaptor that the plunger hangs from down until it reaches the bottom lock nut, and then tighten the upper locknut to the adaptor. Place the plunger, threaded rod, and trip lever back into the hole in the tub and screw the plate back into place.
What is a tub drain?
Bathtub drains consist of a visible trip lever, a plunger that seats in the drain to stop water, and two pieces of threaded rod which connect the lever and plunger. The assemblies are adjustable to fit a wide range of tubs. The first step is to unscrew the plate that holds the trip lever.
How to keep water in tub when it drains out?
Close the stopper, run some water into the tub, and see if it stays. If the water drains out, repeat the process above and lower the plunger a little bit more until you get the bathwater to stay in.
How long does it take for a bathtub to drain?
10 to 20 minutes. Bathtub drain assemblies are mysterious things. Somehow, a lever placed well above the bottom of the tub controls whether the water stays in the tub when it’s wanted, and then allows it to drain when bath time is over. When a tub won’t hold water, the two potential causes are easily repaired.
Who is the master plumber of the old house?
In this video, This Old House master plumber Richard Trethewey shows how bathtub drains work, and how to fix them when they don’t.
How to put a spring clip back in place?
Squeeze the spring clip back into place, joining the pivot rod with the clevis strap tightly.
How to reattach clevis strap to pivot rod?
Reattach the clevis strap to the pivot rod through the same hole you marked when you slid it out. Changing the hole will give you different results than before for the top rod by the sink, making it a bit shorter or longer.
How to move pivot rod?
Take the cleaned or new pivot rod with the ball attached, and insert it back inside the tailpiece where it was before. When you move the pivot in an up-down motion after inserting it, the drain stopper should also move along with it. If that is not the case, it means you need to readjust the drain stopper till the rod goes into the stopper hole, and it moves accordingly.
How to remove pivot rod from tailpiece?
The pivot rod is now only attached to the tailpiece with a retaining nut and gasket. Unscrew the nut from the base and slide it out. Then, pull and slide the gasket ring out of the pivot rod as well.
How to break a clevis strap?
Observe the area where the clevis strap is bound to the horizontal pivot rod. You will see that a spring clip is securing the clevis strap, binding it to the pivot rod. Put some pressure onto that clip to break its grip on the clevis strap. Then slowly take off the spring clip.
What is pivot rod?
A pivot rod is connected to the drain stopper beneath the sink. Before removing the pivot rod, a few parts need to be dismantled first. These include the clevis , spring clip , retaining nut, and gasket. A pivot rod is attached through a retaining nut and gasket to the sink. The clevis is a many-holed vertical strap attached to the horizontal pivot rod with a small spring clip to keep it firmly in place.
Why isn't my sink draining water?
If your sink is not draining water, it’s because of one of two reasons: Your sink’s pop-up drain stopper is damaged, or the pivot rod is rusted or broken.
How does a clevis work?
The flat, slotted clevis is connected by a small spring clip to a pivot rod–and–ball assembly—a rod that runs through a rubber pivot ball and slopes slightly upward to the tailpiece of the stopper. This rod pushes the stopper up or lets it drop down into the drain body.
What is a pop up tub?
A bathtub pop-up is a two-part mechanism: first, the stopper, which has a rocker arm that extends back toward the drain, and second, the overflow assembly, a lever that lifts or lowers a rod with a spring-like end.
How to remove a sink stopper?
If it seems to be linked to the mechanism below, reach under the sink and unscrew the pivot rod retaining nut and pull out the pivot rod to disengage it. Use locking-jaw pliers to loosen it if necessary.
How does a pop up drain stopper work?
Pop-ups are simple mechanical devices that use a system of links and levers to move a drain stoppers up and down to seal a sink bowl or bathtub. Bathroom sink pop-ups are raised and lowered with a lift knob or lever, usually located on or near the faucet body.
Why won't my sink pop up?
Water may leak or refuse to drain around a sink pop-up for a number of reasons. If your sink pop-up won’t pop up or seat properly, fixing it is quite easy—usually just a matter of adjusting a few parts. The culprit is often a buildup of hair around the base of the stopper or the pivot rod mechanism. Or, the clevis may be out of adjustment (see illustration to identify the various parts).
How to keep a drain stopper in good working order?
Keeping the drain clear of hair, soap and shampoo residue, and other debris is one of the best ways to help keep the stopper in good working order.
How to adjust pop up stopper?
Depending upon the type of pop-up, you adjust the way the stopper seats either by adjusting the length of the striker rod or by adjusting the rocker arm.
