how do you get a key out of a key chain

I have generally used two methods for removing keys from keychains: Staple-Remover Method Since staple removers have sharp, thin teeth, simply place the sharp points between the keychain rings and slowly press down. This should spread the keychain apart and make it easy to roll the new key on/take the old key off the chain.

Full Answer

How do I remove a key from my keychain?

I have generally used two methods for removing keys from keychains: Since staple removers have sharp, thin teeth, simply place the sharp points between the keychain rings and slowly press down. This should spread the keychain apart and make it easy to roll the new key on/take the old key off the chain.

How do you remove a staple from a key chain?

Since staple removers have sharp, thin teeth, simply place the sharp points between the keychain rings and slowly press down. This should spread the keychain apart and make it easy to roll the new key on/take the old key off the chain.

How do you get a loose key out of a lock?

If the lock mechanism has become loose, this should stabilize it enough for you to safely pull the key out. Method 3 – Apply a little spray lubricant into the keyhole just above the key. As you apply the lubricant, gently jiggle the lock to release the key.

How do you get a coin out of a key ring?

Get a coin about the size of a quarter. Press the edge of the coin against the key ring at a 45 degree angle, near where it opens; the coin will slide under part of the key ring, lifting the end up. Apply pressure to the coin so that it lifts up the end of the key ring enough to slide the key on. Then slide the key on.

How do you take keys out of a key chain?

1:422:47How To Open A Keyring EASILY With A Coin - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe the part of the keyring. Just like that all that you have to do is simply twist it so the coinMoreThe the part of the keyring. Just like that all that you have to do is simply twist it so the coin is in there and if I twist the coin clockwise or counterclockwise depending.

How do you separate keys?

0:281:50How To Separate Rental Car Keys #1 | Mr. Locksmith Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust twist them just keep on twisting. And use a crimp will. Break. Though there we go and when youMoreJust twist them just keep on twisting. And use a crimp will. Break. Though there we go and when you hand it back to the dealer.

How do you open a key holder?

0:081:08Operating the Master Lock 5400D & 5401D Lock Boxes - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress down on the release button to open the door guide the door down to fully open it to set yourMorePress down on the release button to open the door guide the door down to fully open it to set your own combination.

How do you unlock a key ring?

Right click on the selected keyring and select Unlock from the menu, or alternatively, click the small picture of a closed lock next to the keyring name to unlock the keyring. If the keyring is password-protected, you will be prompted for a password to unlock the keyring.

What is the easiest way to identify a key?

Head of key painted with nail polish to make it easy to find. To make it easy to find the most used keys on your key ring: Color Code Key Head: Paint both sides of the head of the key with brightly colored nail polish. Use a different color for each key, or just mark the most used key.

How can you tell what key a key is locked in?

Identification Methods Name on the key or Lock: Kwikset or Schlage are the most common residential locks and keys. ... Name Abbreviation: Kwikset is “KW” and Schlage is “SC” The most common keyways are KW1 & SC1. ... Name on the lock latch: look at the edge of your door on the latch for a name.More items...•

How do you use key chains?

0:081:08How To Put Keys On Your Keychain | Lennar's How To U - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight in here on your keychain. Then take the key easily slide that right in there remove the stapleMoreRight in here on your keychain. Then take the key easily slide that right in there remove the staple remover. And slice your key right on my key ring and you don't have to mess up your nails.

How do you open a master lock shackle?

1:042:50How to Open the Door and Remove the Shackle on your Master Lock ...YouTubeStart of suggested clipEnd of suggested clipOnce selected go to manage lock and then select remove shackle. Upon selecting remove shackle in theMoreOnce selected go to manage lock and then select remove shackle. Upon selecting remove shackle in the app. The lock box will light green granting removal of the shackle.

How do I open a lock without a key?

Hold the tension wrench twisted in the correct direction and insert the rake into the lock where the teeth of the keys would go. Push and pull the rake out of the lock, twisting it and working by feel. Twist the tension wrench in the correct direction, and the lock should spring open!

What is a split key ring?

0:007:32How To Use A Key Ring - Split Ring - YouTubeYouTubeStart of suggested clipEnd of suggested clipAs well same people try and use scissors to do it can but it's a little bit dangerous. So the methodMoreAs well same people try and use scissors to do it can but it's a little bit dangerous. So the method I'm going to show you is the easiest one.

How do you open acrylic keychain?

0:000:27Photo Keychain Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put pressure on the center with your thumbs. The backing piece should pop right out. Then youMoreAnd put pressure on the center with your thumbs. The backing piece should pop right out. Then you want to take your photo. I just cut this piece out from a coupon slip. It in the space.

How to take off a keychain with staple remover?

Since staple removers have sharp, thin teeth, simply place the sharp points between the keychain rings and slowly press down. This should spread the keychain apart and make it easy to roll the new key on/take the old key off the chain.

How to remove staples from keychain?

Since staple removers have sharp, thin teeth, simply place the sharp points between the keychain rings and slowly press down. This should spread the keychain apart and make it easy to roll the new key on/take the old key off the chain.

What to use to open a crack in a key ring?

I usually use a staple remover to open a crack in the ring and then add or remove the key painlessly.

What to use when you don't have staple remover?

Since I often don't have a staple remover readily on-hand, I usually use a coin. This video and description are helpful:

How to insert a key in a syringe?

Insert the tip, turn sideways and you have enough of an opening to get a small key in.

How to put a coin on a key?

Apply pressure to the coin so that it lifts up the end of the key ring enough to slide the key on. Then slide the key on.

What is a free key?

The FreeKey is made of flat metal shaped into a ring, but the loops pop apart when you squeeze it. It seems like the most direct replacement that would solve your problem.

How to get a key out of a car?

If you are the handy sort of person who has a can of WD40 or graphite lubricant in your vehicle, then squirt it into the keyhole along the key, wait for a ten count and then gently (emphasis on the gently) wiggle the key in the lock. Often this will allow you to extract the key. If you are inside your home, you can then go on in and call the landlord, a locksmith or run down to the hardware and pick up a new lock. One of those little-known things about mechanical items is that once they develop a problem, that problem is only going to get worse.

How to get a broken key out of a lock?

To extract a broken key, you can attempt to gently grasp it with a pair of pliers – the needle-nosed variety work best for this. The next best thing is to run to the local hardware or department store and purchase a key extractor kit. These come in various formats, but they share the ability to gently release the tumbler fingers from the key and allow the key that is stuck in the lock to be removed.

Do home door locks require metal keys?

Most home door locks are mechanical. There are some exceptions in these times for smart homes and programmable locks, but most of us have the old-fashioned locks that require metal keys. Like all mechanical things, locks and keys develop wear and eventually, therefore, problems – like the key stuck in the door. This is frustrating if you’ve unlocked the door and have made it inside because you don’t want to leave that key outside. But it is even worse if you are outside and cannot get inside!

How to remove a key from a switch?

Pull up on the keycap puller to remove the key. The key will slide right off of the switch below that it is attached to. If you need to remove multiple keys, take the key you just took off out of the keycap puller and repeat the process. With wire keycap pullers, you can remove 3 or 4 keys in succession before you need to take them out ...

How to remove a keycap?

Slide your chosen keycap puller alternative underneath a key and pry it off. Gently apply upward pressure with your chosen tool until the key starts to lift off. In some cases the key may not come off entirely with the tool, so finish pulling it off with your fingers.

How to make a paperclip work?

As an alternative to a knife or flathead screwdriver, you can shape a paperclip to work just like a keycap puller. Unbend the paperclip completely, then reshape it into a “U”, and then bend the ends inwards so that they can hook under a key in the same way a keycap puller works.

How to replace keycap puller?

Use a flathead screwdriver or butter knife as an alternative to a keycap puller. Make sure that the screwdriver or knife blade will fit underneath the keys on your keyboard. Remember to be careful if you are using a knife so you don’t cut yourself!

How to know if a keycap puller is plastic?

If you are using a plastic keycap puller, you should hear a click when it has snapped onto the key. With a wire keycap puller, you will need to twist the handle once the prongs are underneath the key to hook the wire loops underneath two corners of the key.

What is the best key puller?

Keycap pullers come in plastic and wire types. The wire variety is considered better than the plastic kind because they are more durable and less likely to scratch the keys. Both varieties will work just fine to remove keys. However, if you are concerned about scratches you should use the wire kind.

How to clean a keyboard that is stuck?

1. Clean underneath the keys you removed. Moisten a cotton swab with water or rubbing alcohol to clean underneath the key. Wipe away any dirt or sticky spots in those hard-to-reach places under the key. If it looks like anything is damaged underneath the key, you should take your keyboard to a computer repair shop for inspection.

How to clear pins on a key?

Method 1 – Wrap a couple of ice cubes in a plastic bag and hold them against the key. The cold should make the metal contract enough for the teeth of the keys to clear the pins. Method 2 – Push against the lock mechanism with one finger or hand while turning the key with the other hand. If the lock mechanism has become loose, ...

What to do if your key gets stuck in a lock?

Don’t, under any circumstances, try to pull the key out using your strength. Even if you’ve got the upper body strength of the Hulk, this isn’t a problem that’s going to be solved by brute force.

How Do Keys Get Stuck In Locks?

Modern locks are intricate, with numerous mechanisms that need to fit precisely together in order for the lock to operate as it should. If any of those mechanisms wear, bend, rust, or accumulate a layer of dirt, it can stop the parts from working correct ly. Keys are no less to blame: if they wear down, they’ll eventually stop fitting into the lock.

How to extract a key fragment?

The Extractor Tool Method – Insert a single or double hooked extractor tool into the keyhole just above the key cuts. Hook the tool onto one of the key cuts and pull. It may take a few attempts, but the key fragment should eventually slide out.

How to get rid of excess product on lock?

Use a rag to wipe away any excess product. Although this step isn’t strictly necessary, it’ll make the next stage in the process much easier. The Tweezer Method – Take a pair of tweezers. They’ll need to be thin enough to fit easily inside the lock.

When to call in a locksmith?

When to Call in the Professionals – If you don’t have the right tools for the job, it’s best to bite the bullet and call in a professional locksmith. Using the wrong tools (or indeed, the wrong method) may damage the lock and end up costing you more in the long run. With the right tools at their disposal, a locksmith should be able to fix the problem and even replace the lock if necessary in less than thirty minutes.

What is the best lubricant for a key?

Spray lubricant like WD-40 makes a great assistant when attempting to retrieve a key stuck in a lock, and most cans come with a tiny straw nozzle for getting into spaces as tight as a keyhole. (If you don’t keep some handy in your car’s trunk, a quick run to the store might be in order.)

How to grab a key with a squirt of graphite?

First, simply slick the keyway with a squirt of spray graphite or lubricant, then attempt to grab any visible end of the key using a pair of needle-nose pliers.

What is a keyhole plug?

The keyhole plug in a pin tumbler lock (found in deadbolts and key-in-knob locks) is just one part of a larger locking cylinder. What’s visible to you, the face of the plug, is the small circle surrounding the keyway—and your stuck key.

How to align pin tumblers?

Push your key in as far as it will go. Turn the key so that the keyway slot is in the exact position it was in when you inserted the key; this is the correct position for the pin tumblers to align in the cylinder. With your other hand, use the tip of your finger to push firmly on the face of the plug next to the key.

Can you break a key in half?

Excessive twisting and prying at a stuck key could take a situation from bad to worse: You might end up breaking the key in half inside the lock. Should this happen, you do have a couple of DIY options still available to you before calling in professional assistance.

Can you get locked out of your house if you leave your keys at home?

Leaving your keys at home isn't the only way to get locked out. If you—and your key—get stuck, try these three fixes to get inside without having to hire a locksmith. It’s been one of those days. You caught every red light on your way home from work, your laundry wasn’t ready at the dry cleaners, and now—when you finally get home ...

Can you get your key out of the front door lock?

You caught every red light on your way home from work, your laundry wasn’t ready at the dry cleaners, and now—when you finally get home and are dying to sink into your sofa—you can’t get your key out of the front door’s lock.

How to pull out a broken key?

With two thin pieces of metal, you can probe the keyway and pull out the key. Line up a piece of metal on both sides of the key. When I say both sides I am talking about the sides that interact with the warding on the lock, not the biting and smooth side. You do not have to put your tools in very far. Just place them in enough to be able to apply pressure firmly. Then pull the broken key towards you. This will probably only move the key out a bit.

How to get a broken key out of a keyway?

Make sure that you have lined up the nozzle of the lubricant so that it is inside the keyway before you spray. You will also need a rag or paper towel to remove any of the excess lube that spills out of the keyway. Also, grab a pair of needle-nose pliers, because even though these methods will remove the broken key, pliers will help to get it out that much faster. Once enough of the key is accessible, you can just pull it free with your pliers.

How to use a broken key extractor?

To use this tool place it inside the keyway along the bitting of the key. To clarify further, you will be trying to hook the teeth on the key with the hook (s) on the extractor. Once placed along the biting, turn and pull, and this should grab and remove the key. Of course, this may take several attempts.

How to tap a cylinder?

To tap the cylinder, you must be able to point the keyway down toward the ground. If you have a padlock or can remove a cylinder, this method may work for you. While the lock is positioned with the keyhole facing down, strike the lock with a hammer. If you could strike a solid surface by slamming the cylinder, this would be ideal. I would recommend striking the keyway side of the lock over striking the back of the lock, but if this is going to work it should work either way.

How to fix a broken key?

Take a small wire or a match and place some super glue on the end of it. Before getting this near the keyway, remove any excess glue or add glue if there is not enough. Too much glue may harm the lock. Not enough will keep the glue from sticking. Hold that match/wire against the edge of the broken key. When you are applying pressure be sure that you are not pushing the broken key further into the lock. Wait the recommended time for the substances to bind and then pull your match away from the lock as if it were the bow of the key.

How long does it take to get a broken key out of a lock?

A professional locksmith can get most broken keys out of a lock in a minute or less. However, many circumstances can make the process take a bit longer. Just keep in mind that the DIY methods of removing a broken key from a lock are likely to take more time – in terms of collecting necessary materials, education, and application.

What to do when a key breaks off?

1. Tweezers. When a key breaks off in the lock, most people go right for the tweezers. Your main concerns should be the thickness of your tweezers and how far the broken key is in the lock. Most tweezers are inappropriately sized for this task and will just end up pushing the key farther into the keyway.