- Measure the perimeter of the doors and windows with a tape measure, climbing a ladder to do so if necessary.
- Wipe the surface around each door or window with a rag to remove dust. This will allow the adhesive light hangers to stick better.
- Note the locations of the nearest exterior outlets in relation to each window or door. ...
- Test each strand of lights by plugging them into an outlet, detangling them as you test them, if necessary.
- Attach a light clip to the end of the first strand, followed by another clip every 12 to 18 inches, or as recommended on the clip package, since this ...
- Start the first light strand at the bottom corner of either a window or door, and work upward. ...
- Remove the adhesive backing from the clip at the end or bottom of the light strand, pressing it in place along the corner of the window or door frame.
- Plug another strand into the first, if necessary; otherwise, plug an extension cord into the end and run the cord to the outlet.
- Repeat Steps 6 to 8 with each window or door being decorated. Plug the extension cord or cords in when finished.
How to properly hang Christmas lights?
- Warm white light
- Impact-resistant bulbs
- Weather-resistant design
- Ability to connect up to 11 strands
How to hang Christmas lights the easy way?
The Simple Way to Hang up Christmas Holiday Lights Outside
- Binder Clips Make It Simple and Easy. To hang up Christmas lights using binder clips, you will need to buy several big boxes of them. ...
- Tips for Using the Clips. ...
- Hanging Christmas Lights Is a Tradition. ...
- Best Places to Buy Christmas Lights. ...
- A Competition and a Tradition. ...
How to hang Christmas lights outside your house?
Method 1 Method 1 of 3: Hanging Lights with Hooks or Clips Download Article
- Choose gutter hooks to quickly hang lights along your gutters. ...
- Opt for shingle tabs to position the lights on top of your roof. ...
- Use adhesive clips or hooks if you have siding or other smooth surfaces. ...
- Leave 6–8 in (15–20 cm) of space between each hook or clip. ...
- Place the male end of the strand near the power outlet. ...
How to hang indoor Christmas lights?
Lights can also be hung indoors during Christmas to improve the decorations and set in the Christmas mood. Lights can be hung on windows, walls, and ceilings. There are different ways to hang lights inside the house depending on where you want to have them.
How do you hang Christmas lights on a door without nails?
No-Nails-Needed Christmas Lights:Hang Your Christmas Lights With Tape.Adhesive Christmas Light Hooks and Clips.Hot Glue Your Lights On.Staple Them In Place.Light Up Your Rain Gutters With Gutter Clips.Boost Your Brick Walls With Brick Clips.Use a Christmas Light Projector.Decorating a Shingled Roof.More items...•
How do you hang Christmas lights on doors and windows?
0:143:33Hanging Christmas lights around windows and doors with ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you just boom just like that actually a little bit more. Just like that and you're just gonnaMoreSo you just boom just like that actually a little bit more. Just like that and you're just gonna hold it for about good 30 seconds let it dry you're gonna do this all the way around the window.
How do you attach Christmas lights to a house without damaging it?
Vinyl siding clips can be used to help string up lights across the side of your house without nails or glue. The clips are simply installed under the siding — just slide them in and you're ready to decorate. After the holidays, lift them right off and your siding will be damage-free.
How do I hang Christmas lights on my garage door?
When it comes to hanging holiday lights around your garage door, use clips and hooks specifically designed for the task. Avoid using metal fasteners like staples or nails if you are attaching lights directly to the trim; the metal can damage the wiring and create a fire or electrocution hazard.
How do I make Christmas lights fit perfectly?
2:1212:25How to Customize Christmas Lights to Fit Your Home - YouTubeYouTubeStart of suggested clipEnd of suggested clipSide of the cord is on the left side and I'm gonna take the wedge. And slide it right on. There weMoreSide of the cord is on the left side and I'm gonna take the wedge. And slide it right on. There we go so that Arthur's connected I've got my male female.
How can I hang Christmas lights outside without outlet?
7 Best Christmas Light Options Without an Outlet!Use Extension Cords.Give Solar Lights a Chance!Use Battery Operated Lights.Bluetooth Lights Are an Option.Don't Forget Rechargeable Lights.Use USB Lights.Give Light Socket Adapters a Go.
How do you hang Christmas lights without damaging wood?
Whenever possible, use plastic clips when hanging Christmas lights. There are a variety of plastic clips that work by clipping onto the gutters, shingles or eaves of your home without damaging your roof. There are clips available for specific roof systems and Christmas lights.
How do you attach Christmas lights to wood trim?
0:201:41How To Hang Christmas Lights Around A Door - Ace HardwareYouTubeStart of suggested clipEnd of suggested clipAnd place the double-sided tape onto the clip. Then put the clip onto each individual bulb this willMoreAnd place the double-sided tape onto the clip. Then put the clip onto each individual bulb this will allow even spacing. So you have that symmetrical.
How can I hang Christmas lights without damaging paint?
Stick a small adhesive decorating clip to the walls in each place you want to attach a strand of lights. To secure a vertical stretch of lights going straight up or down the wall, face the clips in alternating directions to make the arrangement more secure.
How do you hang a wreath on a garage door?
Most garage door frames have one piece of wood flush to the outside wall. Nailing a nail into it at a 45° angle will hold the fishing line reliably. Loop the line down around the wreath hanger. The wreath will hang a bit in front of the garage door rather than against it.
How do you hang lights in a garage?
3:296:37How to Install DIY Garage Lighting + New Electrical - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you could get a better idea of where they would work best for each light we check to see if thereMoreSo you could get a better idea of where they would work best for each light we check to see if there was a stud where we wanted to place the light if not we drill a pilot hole.
How do you hang Christmas lights on brick?
0:594:32Attaching Christmas Lights to Brick with Hot Glue - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to apply a line of hot glue. On the base of the socket. And make sure the flared part isMoreWe're going to apply a line of hot glue. On the base of the socket. And make sure the flared part is going to hang off the brick. We're going to hold the socket. For just a few seconds.
How do you hang string lights indoors?
Hanging String Lights Indoors One secure option that works for most walls is to use a hammer and nails. Leave a part of the nail protruding from the wall and drape the string lights over the nail. If you are hanging fairy lights, a thumbtack should be enough to support the weight of the lights.
How do you hang Christmas lights on a two story house?
1:2911:09Easy Christmas Lights Install On Two Story house - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou know some of them need to it puts friction on the wire it does no friction on the water you canMoreYou know some of them need to it puts friction on the wire it does no friction on the water you can just see it holds it pretty strong they make these also they go up into there into the roof.
How do you put rope lights around a window?
Install the clips around the perimeter of the window, inside the frame, spaced about every 4 to 6 inches. The mounting clips can be mounted with small nails or screws. Do not mount clips too close to the corners. Even though rope lights are fairly flexible, they cannot bend at a 90-degree angle.
How do you hang lights in a room without nails?
How to hang lights in a room without nailsUse adhesive clips. With damage-free adhesive hooks or clips, you can deck the halls without nails or stress. ... Drape on furniture. ... Wrap around banisters. ... Use brick and brick clips. ... From a curtain rod. ... Transparent tape. ... Wrap around household objects. ... Staples.More items...
How to decorate your home for Christmas?
Taking your time to hang lights securely ensures they're able to withstand strong winds and stay put for the entire season. Use only lights and extension cords rated for outdoor use, as these are made to withstand the elements.
How to get dust off of window light hangers?
Wipe the surface around each door or window with a rag to remove dust. This will allow the adhesive light hangers to stick better.
How to test a light strand?
Test each strand of lights by plugging them into an outlet, detangling them as you test them, if necessary. Replace defective light strands or those with exposed metal wires.
Why use only lights and cords designed for outdoor use?
Use only lights and cords designed for outdoor use to avoid potential safety hazards.
How to connect extension cord to outlet?
Plug another strand into the first, if necessary; otherwise, plug an extension cord into the end and run the cord to the outlet. If using more than one strand per window or door, peel the adhesive backing off the respective clips and press them into place.