how do you install a moen kitchen faucet sprayer

Follow these steps to install the Moen kitchen faucet sprayer:

1. Open the Cabinet that holds the faucets.
2. Remove the old spout from the faucet and place it on top of the new spout.
3. Place the new spout into position on the faucet body.
4. screw in the nuts and bolts to secure the faucet sprayer to the Faucet body.

Full Answer

How to install a Moen kitchen faucet?

Installing a Moen kitchen faucet is relatively easy and can be done in just a few steps. There are usually two valves under the sink; one for hot water and one for cold water Place a bucket or bowl under the sink to catch any water that may drip out when you remove the old faucet

How do you install a sprayer hose on a kitchen faucet?

This tailpiece is also the housing for the sprayer hose. Use the installation tool provided with the faucet to tighten the mounting nut most of the way. Check the position of the faucet above the sink, then finish tightening the mounting nut until the faucet is tight enough that it won't move.

How to replace a kitchen sink faucet?

Instructions 1 Disconnect the Water Supply. Shut off the water to the old faucet by closing the fixture shutoff valves on the hot and cold water supply pipes under the sink. 2 Remove the Old Faucet. Remove the old faucet by loosening the mounting nut (or nuts) that secure the faucet on the underside of the sink. 3 Install the New Faucet Body. ...

How do you tighten a Moen valve stem?

Next, place rubber O-rings provided by Moen onto each valve stem – one per side – located inside each handle hole. With everything in place, the hand tightens each mounting nut until snug using an adjustable wrench being careful not to overtighten and strip them.

How to connect a hot water faucet to a cold water pipe?

How to test a spray hose?

How to turn water back on?

Where to place a sprayer hose?

Can you use a escutcheon kit on a three hole sink?

Do faucets have preattached tubes?

Who is Aaron Stickley?

See 2 more

How do you replace a Moen kitchen faucet sprayer?

0:402:48Turn off the water supply lay a towel under the sink and press the sprayer trigger to releaseMoreTurn off the water supply lay a towel under the sink and press the sprayer trigger to release pressure. Follow the sprayer hose and you'll see that it connects underneath the faucet.

How do you install a Moen kitchen faucet with pull down sprayer?

0:174:47Position the deck plate. And it's gasket over the center mounting hole to cover the holes you don'tMorePosition the deck plate. And it's gasket over the center mounting hole to cover the holes you don't need then insert the hoses and faucet shank into the mounting hole.

How do you install a kitchen faucet sprayer attachment?

0:582:58Start by installing the new guide in a sink opening and tighten the nut from the bottom of the sink.MoreStart by installing the new guide in a sink opening and tighten the nut from the bottom of the sink. Then unscrew the nut from the sprayer push the hose through the nut clip the clip onto the hose.

How do you take apart a Moen kitchen faucet sprayer?

0:062:01And you see how the whole thing spins. Okay it means you're doing good your twist down once you getMoreAnd you see how the whole thing spins. Okay it means you're doing good your twist down once you get it loose. Enough you can just use your thumbs.

How do you remove a Moen single handle kitchen faucet sprayer?

How to Remove the Sprayer on a Moen 7900 FaucetTurn off the valves under the sink by rotating the valve handles counterclockwise.Hold the hose in one hand and push upward on the hydrolock connection with the other to disconnect the sprayer from the diverter. ... Pull the sprayer straight upward and out of the guide.More items...

How do you replace a spray head on a pull down faucet?

0:110:41The spray head will simply unscrew. Just like a light bulb. Now you're going to feed the hose backMoreThe spray head will simply unscrew. Just like a light bulb. Now you're going to feed the hose back into the faucet. Finally turn on the water supply. And run the faucet to check for leaks.

How do you install a sprayer on an existing faucet?

Choose the Right Faucet. ... Drill a Mounting Hole into Your Sink. ... Turn Off the Water. ... Connect the Supply Lines to the Faucet. ... Apply Sealant and Position the Faucet. ... Screw On the Faucet Mounting Nuts. ... Connect the Supply Lines to the Shutoff Valves. ... Apply Sealant to the Side Sprayer Base.More items...

How do I fix my Moen sink sprayer?

0:060:53You might need pliers to squeeze the clip back into place install the washer and screw on the newMoreYou might need pliers to squeeze the clip back into place install the washer and screw on the new spray. Head. Now you're ready to rinse some dishes.

Can you replace just the sprayer on a kitchen sink?

Whether you're installing a sink sprayer replacement or adding a new sprayer to your current kitchen faucet set-up, it's a pretty quick and simple update. It's also a cost-effective alternative to installing an entirely new faucet with a sprayer.

How do you remove a Moen spray head?

0:121:35Simply pull out the hose a little bit there's a lock nut right.MoreSimply pull out the hose a little bit there's a lock nut right.

How do you remove a Moen quick connect sprayer?

Press the white button (A) in to lock the faucet part in. Gently tug on the quick connect to verify it is secure. Removal: Press and hold the black button (B) while pulling the faucet part out of the quick connect.

How do you replace a sprayer on a kitchen faucet?

0:382:13Then pull up on the old sprayer hose underneath loosen the mounting nut that connects the oldMoreThen pull up on the old sprayer hose underneath loosen the mounting nut that connects the old sprayer to your sink. Then remove the assembly. To install the new sprayer.

How do you install a single handle kitchen faucet with side sprayer?

Choose the Right Faucet. ... Drill a Mounting Hole into Your Sink. ... Turn Off the Water. ... Connect the Supply Lines to the Faucet. ... Apply Sealant and Position the Faucet. ... Screw On the Faucet Mounting Nuts. ... Connect the Supply Lines to the Shutoff Valves. ... Apply Sealant to the Side Sprayer Base.More items...

How do you install a push down drain from Moen?

0:491:58Take a pair of pliers. And loosen the lock nut remove the p-trap to free up the tail pipe then goMoreTake a pair of pliers. And loosen the lock nut remove the p-trap to free up the tail pipe then go ahead and remove the old flange. You'll want to clean up the area of the drain hole in the sink.

How do you hook up a pull down faucet hose?

0:522:51Place the weight on the hose. Thread the hose into place until it's tight and secure it with aMorePlace the weight on the hose. Thread the hose into place until it's tight and secure it with a quarter turn with a wrench follow these steps if your host style is quick disconnect.

How do you use a Moen cartridge pull tool?

0:464:20That comes out of the bottom you want to loosen that up a little bit you'll see down on this sideMoreThat comes out of the bottom you want to loosen that up a little bit you'll see down on this side there's a screw in there that will connect inside our cartridge there's an opening for a screw there.

How to connect a hot water faucet to a cold water pipe?

Connect the hot and cold supply tubes of the faucet to the shutoff valves on the hot and cold water supply pipes, using compression fittings. Thread the compression nut for each line onto the corresponding shutoff valve and tighten the nut with two pairs of pliers—one to hold the valve body and one to tighten the nut. Make sure the flexible tubes won't interfere with the spray hose and are not kinked.

How to test a spray hose?

The weight must move up and down freely with the spray hose; test it by moving the spray wand in and out of the faucet spout. The hose should move easily without hitting anything under the sink.

How to turn water back on?

Turn the water back on by opening the shutoff valves all the way (turning counterclockwise). Check the faucet for proper operation and confirm there are no leaks in the flexible tubes or the spray hose.

Where to place a sprayer hose?

Place the rectangular support plate into position on the underside of the sink, fitting it over the supply tubes and the threaded tailpiece of the faucet body and up against the bottom side of the sink. Place the round plate under the rectangular plate, then thread the brass mounting nut onto the faucet tailpiece. This tailpiece is also the housing for the sprayer hose.

Can you use a escutcheon kit on a three hole sink?

If you are using the optional escutcheon kit to cover unused sink holes (for three- and four-hole sinks), position the plastic spacer and escutcheon onto the sink before installing the faucet body.

Do faucets have preattached tubes?

Some faucets do not include the preattached supply tubes and will require that you buy separate flexible supply tubes.

Who is Aaron Stickley?

Aaron Stickley is a licensed plumber with first-hand knowledge in solving home plumbing problems.

How to connect a hot water faucet to a cold water pipe?

Connect the hot and cold supply tubes of the faucet to the shutoff valves on the hot and cold water supply pipes, using compression fittings. Thread the compression nut for each line onto the corresponding shutoff valve and tighten the nut with two pairs of pliers—one to hold the valve body and one to tighten the nut. Make sure the flexible tubes won't interfere with the spray hose and are not kinked.

How to test a spray hose?

The weight must move up and down freely with the spray hose; test it by moving the spray wand in and out of the faucet spout. The hose should move easily without hitting anything under the sink.

How to turn water back on?

Turn the water back on by opening the shutoff valves all the way (turning counterclockwise). Check the faucet for proper operation and confirm there are no leaks in the flexible tubes or the spray hose.

Where to place a sprayer hose?

Place the rectangular support plate into position on the underside of the sink, fitting it over the supply tubes and the threaded tailpiece of the faucet body and up against the bottom side of the sink. Place the round plate under the rectangular plate, then thread the brass mounting nut onto the faucet tailpiece. This tailpiece is also the housing for the sprayer hose.

Can you use a escutcheon kit on a three hole sink?

If you are using the optional escutcheon kit to cover unused sink holes (for three- and four-hole sinks), position the plastic spacer and escutcheon onto the sink before installing the faucet body.

Do faucets have preattached tubes?

Some faucets do not include the preattached supply tubes and will require that you buy separate flexible supply tubes.

Who is Aaron Stickley?

Aaron Stickley is a licensed plumber with first-hand knowledge in solving home plumbing problems.