- Begin by draining the pool. ...
- Remove fittings, lights, gaskets and any step seal strips. ...
- Cut the liner away from your pool walls using a utility knife. ...
- Lay your liner out in the pool starting at the deep end. ...
- Begin connecting the liner bead to the bead receiver from the deep end. ...
Full Answer
Where to start to attach a pool liner?
How many directions can you attach a pool liner?
How to pull a pool liner over?
What to do before installing pool liner?
How to measure for above ground pool?
How to get rid of a pool?
Where is the simmer pump in a pool?
See 2 more
How do you collapse a round pool liner?
9:1211:23Intex Ultra Frame Pool Draining and Take Down - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd start by folding the walls of the pool liner think of the pool. Even if it's round. Think of itMoreAnd start by folding the walls of the pool liner think of the pool. Even if it's round. Think of it as if it's a square. And start by folding the opposite sides. And then fold the other two sides.
Can you install a pool liner yourself?
Replace your own inground pool liner, and save thousands of dollars over local installers! Installing your own inground pool liner is easy, when you take it step by step.
How do you install an above ground pool liner?
How to Install an Above-Ground Pool LinerDrain the water from your pool. ... Unfold your pool liner and place it in the swimming pool. ... Remove the rail assembly from the top of your pool and install the liner on one side. ... Repeat this process until the liner is installed on all sides of the pool.More items...
What is the easiest pool liner to install?
Beaded pool linersBeaded pool liners are the easiest type of liner to replace. Using a bead receiver that hangs over the top of the pool wall, the beaded liner simply snaps into the bead receiver giving you an even and consistent look.
What goes underneath a pool liner?
Underneath the liner is a sand or cementitious floor, troweled into place. The floor sidewalls come up to meet the walls, which are commonly 42” x 8 ft panels made of galvanized steel or thermoplastic. These walls are supported from behind so that they won't bow out against the weight of the water.
What is the best thing to put under a pool liner?
Pool Floor Padding By far the best material to place under a swimming pool liner is Armor Shield or Gorilla Pad. These materials are breathable allowing moisture to escape and are extremely tough, keeping insects and moles from coming through and piercing the vinyl pool liner.
Can I install an above ground pool liner myself?
If you find yourself needing to replace your above ground swimming pool liner, either because of tears or excessive staining, you don't need to hire a professional. As long as you have a little time on your hands, you can save yourself some serious money by doing it yourself.
How tight should a pool liner be?
There should not be any wrinkles, however, there will most likely still be a very small air gap between the liner and the cove. 3-5” is ideal, but a little more is ok. The liner will stretch in place further once water is added.
Should I put a pad under my pool liner?
Yes! It is always a good idea to use padding under your liner as another layer to prevent roots, stones, or other debris from making a hole in your liner and causing a leak. There are many different kinds of padding on the market, to name a few there are: Gorilla Pad, Happy Bottom, and Foam Pad.
What kind of sand do you use under a pool liner?
mason sandWhat Type of Sand Should I Use? For your pool's base, you want sand that's very fine and free of any rocks or pebbles. This type of sand is referred to as mason sand, masonry sand, or sometimes mortar sand. While mason sand is the most popular choice, another option is concrete sand.
Why are most pool liners blue?
Since pool water is colorless on its own, many owners choose blue swimming pool liners to reflect the natural color of water. Water reflects the blue color of the sky due to Rayleigh scattering, giving the effect that the water is also blue.
Is a lighter or darker pool liner better?
Your pool liner is no different. A light pool liner is going to give a light, airy feel — kind of like a beach or tropical vibe. Dark-colored liners, on the other hand, can give your pool a rich, bold look and make your pool seem deeper.
How long does it take to install a pool liner?
Most pool liners can be replaced in 1-4 days once the new liner is delivered, assuming the weather is accommodating. Although you aren't usually required to stay at home while the liner is installed, we recommend that you do so that you can ask the pool pros any questions you might have.
How much does it cost to put a new liner in a pool?
Inground pool liner replacement costs $3,000 to $4,000 on average with prices ranging between $1,400 and $4,800 for materials and labor. Above ground swimming pool liner replacement runs between $350 and $1,600 with most spending $700 on average.
How much does it cost to install a vinyl pool liner?
How much does a vinyl liner pool cost? Most vinyl liner pools cost $65,000–$85,000upfront. If you choose a vinyl liner pool the homeowner has the ability to customize any type of pool that you would like to have in your backyard ( Shape & Size ). Vinyl liner pools cost about $11,500 in maintenance over 10 years.
Can I install an above ground pool liner myself?
If you find yourself needing to replace your above ground swimming pool liner, either because of tears or excessive staining, you don't need to hire a professional. As long as you have a little time on your hands, you can save yourself some serious money by doing it yourself.
Where to start to attach a pool liner?
When you start to take the liner and attach it, you want to start at the north-most point of the pool . You take the liner and secure it with the coping, top metal, and the top rail in that spot. Then move to the south, then east, then west and repeat the process.
How many directions can you attach a pool liner?
Once your liner has your 4 direction points attached to the walls, add 4 more in between those points and attach (Northwest, Northeast, Southwest, Southeast). You may now attach the liner with coping, or into the bead receiver, all the way around the pool.
How to pull a pool liner over?
When the liner feels tight and is difficult to pull up and over the wall, try taking the pool liner and leaning into it with your chest and use your body weight to stretch it out and pull it over. Then pull on it from the outside. They're meant to stretch.
What to do before installing pool liner?
Before installing your liner, make sure the area around your pool is safe and secure. That may mean mowing the grass, picking up toys in the yard, trimming bushes and tree branches, sanitizing your patio area, and making sure children and pets are indoors.
How to measure for above ground pool?
To accurately measure your above ground pool, measure from inside to inside of the pool wall with a tape measure. If you think of your pool as a clock face, measure from 12 to 6 and 9 to 3. Once you’ve double-checked the measurements, you can make sure you have the right box with the right size pool liner and avoid any trouble or hiccups down ...
How to get rid of a pool?
Start by making sure ALL the water is drained out of your swimming pool. As you’re pumping out the water, make sure you’re pumping it as far away as possible to avoid making a mess underneath your pool.
Where is the simmer pump in a pool?
The simmer pump lays at the bottom of the pool and gets the water level down to almost nothing. As an added bonus, it’s a great tool for pumping water off your winter pool cover as well.
Where to place pool liner?
Starting at the liner’s wall seam, place the liner on the top of the pool wall with the print side facing up and the flaps for the seams facing down. Do not take apart the rails at this time.
What is the best way to keep pool liner from coming unclipped?
PRO TIP: An alligator clip or a person holding the section where you start will also be helpful to maintain wall stability and keep the liner from coming unclipped as you go around the pool.
How to find the amount of pool liner you need?
To find the amount of liner you should be overlapping, find the seam that connects the wall of the liner to the floor of the liner. Position it just about to the top of the pool cove. By the time the liner is completely installed, you’ll see if you need to let more overlap back in or pull some extra out.
How many seams are there in a pool liner?
Identify the floor seams in the liner. Oval liners typically have two seams that run the length of the pool. They are not in the center of the floor but each one is off center to either side. Use these seams to help install the liner squarely within pool.
Why is a pool liner important?
Its purpose and design is to form a water seal. Water pressure is held by the pool wall and frame and not by the liner. A properly installed liner must be supported by the ground, cove and the pool wall.
How to measure for a pool liner?
One way is to find and mark the center of your pool frame with an alligator clip or clothes pin on each end. This will be the center on the rounded ends, not the straight sides. Then measure the distance between the two floor seams. Then divide that measurement in half. EXAMPLE: if the distance between Floor Seam A and Floor Seam B is 5’ (or 60”), divide 5’ in half and you get 2.6’ (or 31.2”). Then measure 2.6’ from either floor seam (A or B) towards the center of the pool. This is the center line of your oval liner. Measure that distance (2.6’, in our example) in towards the center of the pool in several places, and make sure the center line of the liner is aligned with the center of your pool frame. *The numbers provided in the example above are for demonstration purposes only. You will have to take your own measurements as these distances vary from liner brands, types, and pool sizes.
What happens if you have too much liner in a pool?
If you have too much liner inside the pool it will not have this air gap. You’ll need to overlap more liner over the pool wall. If you have too much of an air gap, you have too little liner inside the pool and will need to let some of the overlap back into the pool.
When to install pool liner?
Once the floor is ready – install the liner quickly before debris blows into the empty pool.
What is the measurement of a pool liner?
The corners of the pool, at the top of the wall, have a specific radius measurement. And, most pools have square measures – with both ends and both sides being the exact same length.
What color pool liner should I use for a pool?
One of the fun parts of putting in a new pool liner is choosing a new pattern or style. Darker colors will absorb slightly more solar energy. Tan and Grey tones have become popular lately, to blend with neutral backyard colors. Most patterns have a mottled pattern, to help hide dirt and mask wrinkles or imperfections. If you can afford it, I would always recommend choosing a thicker liner – 28 or 30 mil, rather than a standard 20 mil pool liner.
How to get rid of algae in pool?
To get every last drop of water, and drain the pool completely, remove the main drain cover and use a sponge and bucket. You can also use a cover pump, or a wet/dry vac or even old towels, to get up the last few gallons. Set aside the drain cover and screws for now.
How to measure pool width?
To measure width of the pool (I, J, K), use a pool pole held vertically in the corner of the hopper, and measure horizontally from the liner track to the pole. Do not measure down the side-slope, the measuring tape should be horizontal. Switch sides and measure the width of the opposite side wall.
How many people do you need to install a vinyl pool liner?
A vinyl liner installation is easily done with two people, having a third or fourth person on the job is helpful, especially when you are pulling the liner across the pool, and locking the bead into the track. Planning your installation during spring break, or stretched out over several weekends, may help in obtaining helpers. Pay a decent wage, and you should have no trouble putting a small team together.
What happens if you discharge water from a pool?
Discharge the pool water too close to the pool , and it can weep into the pool, or put pressure on weak walls.
Where do you put a beaded liner in a pool?
Beaded Liners. The liner snaps into a bead receiver or track that runs around the top inside portion of your pool. You will have to had to of ordered the bead receiver or bead track along with your kit in order to install your liner as a beaded liner does not automatically come with it.
How to hold a beaded pool liner in place?
PRO TIP: You can use masking or electrical tape, if necessary, to hold the liner in place.
How to get pool liner to be evenly distributed?
If there are wall wrinkles, shift the liner in the track until the liner is even. Then continue snapping the remainder of the liner into place around the pool.
What is a Unibead liner?
UniBead liners are the most popular liner choice for above ground swimming pools. You can install Unibead, or J-Hook/V-Bead, in 2 separate ways: as a standalone J-hook shown here where you simply "hang" the liner on the wall. Or as a Beaded Liner with a bead receiver as shown under "beaded Liner".
What is an overlap liner?
Overlap Liners. The liner literally overlaps/drapes over the side of your pool wall and is then secured by the pool's top rails. TIP: If your pool has a deep end, you’ll have an overlap liner. Specifically, an expandable liner. These can range in depth from 60" to 80"+ with the most common being 72".
How far should a pool liner go over the wall?
This will assure you that the liner begins going over the wall straight. The liner should have the loose end overhanging the outside of the pool by approximately 12”. Hold the loose end and unfold the liner down and across the middle of the pool.
What temperature should a pool liner be?
The minimum temperature should be 65 degrees. If lower, try to warm the liner first. Open your liner box carefully so the liner is not damaged. Do not use sharp objects to open the liner box. Check the pool floor for levelness. Remove all stones and sharp objects to keep your liner from being punctured.
Where should a curved seam be on a pool liner?
The curved seam should be centered on the cove at the base of the wall. The other seams will form straight lines across the bottom of the pool. Smooth out all wrinkles in the bottom. Smooth out the floor of the liner by pushing it toward the pool wall. A soft push broom will be very helpful.
Why is my pool liner not creased?
The liner should not have creases in it because it is twisting around the pool. If the liner is twisting, it is because it is not sitting properly in the pool. Make necessary adjustments before proceeding. Start filling the pool with only a few inches of water.
What is the easiest type of liner to replace?
Beaded pool liners are the easiest type of liner to replace. Using a bead receiver that hangs over the top of the pool wall, the beaded liner simply snaps into the bead receiver giving you an even and consistent look. Because they install evenly around the pool wall, beaded liners form beautiful designs and patterns including wall borders and tile trims.
What is the best place to find everything you need to own a pool?
America’s Above Ground Pool Experts – is the best place to find everything you need to make owning a swimming pool or spa fun and easy, at the best prices today. With a combined 50+ years of experience The Pool Factory employs a highly trained staff of above ground and semi inground pool specialists. The Pool Factory can provide unique solutions for all pool supplies and swimming pool needs.
What happens if you don't attach a wall around a pool?
If you do not attach the wall in this manner and begin from one location and your wall completely around the pool, one of two situations will exist. Either you will have an excess of material or flap on the circumference of the wall or you will be short and have to stretch the material to make it fit.
Is there air between a foam pool liner and a sand base?
There should be NO AIR SPACE between the liner and the base that it’s resting on, especially at the cove area (where the pool wall and the angled sand base meet). If you installed the foam pool cove on top of the 3” sand base and noticed there is still air behind the liner it’s recommended to add additional fine mason sand to help reduce the stress and tension on the vinyl liner and the pool wall.
Can you put sand on top of a foam pool liner?
Adding mason sand to the cove area will help alleviate the unwanted stress on the pool wall and the liner. You can also add mason sand on top of the foam pool cove.
Where should a curved seam be on a pool liner?
The curved seam should be centered on the cove at the base of the wall. The other seams will form straight lines across the bottom of the pool. Smooth out all wrinkles in the bottom. Smooth out the floor of the liner by pushing it toward the pool wall. A soft push broom will be very helpful.
Where is the J hook on a pool liner?
The J-hook is pre-attached by the liner manufacturer to the top of the liner and hangs directly on the top of the pool wall when installed. Since it is custom fit for the height of the pool, with the proper amount of sand on the ground surface, there will be no need to adjust the liner height during installation.
Why is my pool liner not creased?
The liner should not have creases in it because it is twisting around the pool. If the liner is twisting, it is because it is not sitting properly in the pool. Make necessary adjustments before proceeding. Start filling the pool with only a few inches of water.
What is the best place to find everything you need to own a pool?
America’s Above Ground Pool Experts – is the best place to find everything you need to make owning a swimming pool or spa fun and easy, at the best prices today. With a combined 50+ years of experience The Pool Factory employs a highly trained staff of above ground and semi inground pool specialists. The Pool Factory can provide unique solutions for all pool supplies and swimming pool needs.
What happens if you don't attach a wall around a pool?
If you do not attach the wall in this manner and begin from one location and your wall completely around the pool, one of two situations will exist. Either you will have an excess of material or flap on the circumference of the wall or you will be short and have to stretch the material to make it fit.
Is there air between a foam pool liner and a sand base?
There should be NO AIR SPACE between the liner and the base that it’s resting on, especially at the cove area (where the pool wall and the angled sand base meet). If you installed the foam pool cove on top of the 3” sand base and noticed there is still air behind the liner it’s recommended to add additional fine mason sand to help reduce the stress and tension on the vinyl liner and the pool wall.
Can a J hook be used as a bead liner?
This article covers the J-Hook installation method. J-hook liners have a special attachment that is referred to as the “ J-hook”. The J-hook is pre-attached by the liner manufacturer to the top ...
How to make a pool liner?
Step 1 - Preparation. Make sure that you install your pool liner on a warm day where the temperature is 75° or more. Drain all of the water out of the pool and remove the old liner. Then, make sure that you use fresh sand, also referred to as pool sand (do not use standard torpedo sand). Finally, make sure that you order ...
How long does it take to install a beaded pool liner?
You will probably need some assistance as most pool liners are rather large and cumbersome. This project can generally be completed in 2 hours or so.
How to get rid of wrinkles in pool?
Start filling your pool with water. As the water begins to increase in volume, continue to push the wrinkles out of the liner towards the pool wall to reduce tightness in the corners. Stay inside the pool until it's filled with approximately 3 inches of water.
Can pool liner be straight?
The liner does not need to be perfectly straight but you should try to make sure the liner is centered and as flat as possible.
Where to start to attach a pool liner?
When you start to take the liner and attach it, you want to start at the north-most point of the pool . You take the liner and secure it with the coping, top metal, and the top rail in that spot. Then move to the south, then east, then west and repeat the process.
How many directions can you attach a pool liner?
Once your liner has your 4 direction points attached to the walls, add 4 more in between those points and attach (Northwest, Northeast, Southwest, Southeast). You may now attach the liner with coping, or into the bead receiver, all the way around the pool.
How to pull a pool liner over?
When the liner feels tight and is difficult to pull up and over the wall, try taking the pool liner and leaning into it with your chest and use your body weight to stretch it out and pull it over. Then pull on it from the outside. They're meant to stretch.
What to do before installing pool liner?
Before installing your liner, make sure the area around your pool is safe and secure. That may mean mowing the grass, picking up toys in the yard, trimming bushes and tree branches, sanitizing your patio area, and making sure children and pets are indoors.
How to measure for above ground pool?
To accurately measure your above ground pool, measure from inside to inside of the pool wall with a tape measure. If you think of your pool as a clock face, measure from 12 to 6 and 9 to 3. Once you’ve double-checked the measurements, you can make sure you have the right box with the right size pool liner and avoid any trouble or hiccups down ...
How to get rid of a pool?
Start by making sure ALL the water is drained out of your swimming pool. As you’re pumping out the water, make sure you’re pumping it as far away as possible to avoid making a mess underneath your pool.
Where is the simmer pump in a pool?
The simmer pump lays at the bottom of the pool and gets the water level down to almost nothing. As an added bonus, it’s a great tool for pumping water off your winter pool cover as well.