how do you install a sand filter pump

How to Hook Up a Sand Filter Pump to an Above Ground Swimming Pool

• 1. Place the sand filter close to the pump. ...
• 2. Turn off the pool pump’s circuit breaker. ...
• 3. Slide hose clamps onto each end of your flexible pool hose. ...
• 4. Connect another hose to the outlet port on your pump. ...
• 5. Push the final length of hose over the outlet port on the sand filter. ...
• 6. Turn on the pump’s circuit breaker. ...

Full Answer

How to install a sand filter for a pool pump?

Place the sand filter close to the pump. Make sure to locate it near the skimmer and return on your pool. Ensure the ground is level beneath the pump and filer. Place the pump and filter on concrete blocks for additional stability. Turn off the pool pump’s circuit breaker. Pumps can be hardwired to the breaker, or plug into an outdoor receptacle.

How do you backwash a pool with a sand filter?

Connect the other end of this hose to the inlet port on the side of your pool. Turn on the pump’s circuit breaker. Move the lever on the sand filter to the “backwash” position. Turn on the above-ground pool pump. Allow the pump to run for about two minutes to remove any impurities from the silica sand in the filter.

How do you clean an above ground sand filter?

Move the lever on the filter to the “rinse” position. Turn on the pump on for about one minute, or until you observe clear water in the filter’s sight glass. Turn off the pump. Rotate the lever on the above-ground sand filter to the “filter” position. Turn on the pump to operate the filter and pump normally.

How do you hardwire a pool pump to the ground?

Ensure the ground is level beneath the pump and filer. Place the pump and filter on concrete blocks for additional stability. Turn off the pool pump’s circuit breaker. Pumps can be hardwired to the breaker, or plug into an outdoor receptacle.

How do you hook up a sand filter pump?

2:068:48Bestway Sand Filter Setup Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure the seal is in place and connect a hose to port B on the filter and port B on the pool.MoreMake sure the seal is in place and connect a hose to port B on the filter and port B on the pool. Connect the other hose to port D on the filter.

How do I install a sand pump for my pool?

7:1310:34Intex 1600 gal/hr Sand Filter Pump Setup Instructions - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure the pump motor switch is in the off position. And depress the six-way valve turning it toMoreMake sure the pump motor switch is in the off position. And depress the six-way valve turning it to backwash. Always depress the valve handle to turn it connect the motor cord to an AC outlet.

How do you install a sand filter for the first time?

0:462:05How to start your sand filtration system for the first time - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're gonna have to what we call burp the pump. So when the pump is first turned on. You're gonnaMoreYou're gonna have to what we call burp the pump. So when the pump is first turned on. You're gonna take the cap. And twist it a little bit just to let air into the system.

Does the pump go before or after the sand filter?

When installing the pool sand filter, you will connect it right after the pump. Pool water will come in through the pool pump, be filtered through the sand filter and released to the chlorinator before returning back to the pool.

Do you use chlorine with a sand filter?

Sand filters use chlorine because the sand is added for filtration, but chlorine sanitizes the swimming pool water. Sand, cartridges, and DE can't replace chlorine because they have different purposes. However, you can use swimming pool robots, salt systems, and other tools to improve your pool water.

How much sand do I need for a sand filter?

How Much Sand Does My Pool Filter Need?Filter Model / SizePounds Required (Sand)Filtra Balls Required (Boxes)16 Inch100 Lbs2 Boxes19 Inch150 Lbs3 Boxes21 Inch200 Lbs4 Boxes23 Inch250 Lbs5 Boxes19 more rows

Can I leave my sand filter out all winter?

Even if your filter itself doesn't crack, leaving it outdoors for the winter could cause premature wear and tear. Chances are that if you've already picked out the right filter for you, you know they don't come cheap. Make sure you take care of yours by winterizing it properly and storing it away in a safe, dry place.

How often should you change sand in pool filter?

every 3-5 yearsWhen do I need to replace my sand? On average, sand should be replaced every 3-5 years. This may be longer if the pool stays clear, or shorter, if the filter runs all the time. The jagged edges of the sand wear down and become smooth as the sand ages.

How often should I run my sand pool filter?

It is recommended that you turn over the water in your pool at least twice a day (refer to chart at bottom of page for your pools capacity). Run filter more in hot weather or with heavy bather load. As a general rule of thumb, turn your sand filter on 1 hour per 10° F of weather.

Should I run my pool pump while swimming?

Only while it is active can the filter be effective at removing dirt. Therefore, you should ideally run your pool pump for as long as possible to ensure your swimming pool stays clean and healthy.

How long does pool sand filter last?

Your sand filter can last anywhere from 15 years to 25 years or more if cared for and maintained well. Most of the time, you may need to replace parts like valves and gaskets, but you probably won't need to replace the whole system for many years.

Can you run a sand filter without sand?

Each lateral is full of tiny perforations large enough to allow water to pass through the filter, but not sand. If, for some reason, one or more of the laterals crack, sand will easily pass through and be sent into your pool along with the clean water.

How do I connect a sand filter to my pool?

3:485:05Installing A Pool Sand Filter Yourself Is Not Impossible - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere we go our three bags of sand have been poured in and we can remove the plastic packet from theMoreThere we go our three bags of sand have been poured in and we can remove the plastic packet from the breather cap put the o-ring seal in place replace the lid. And tighten up the screws.

How do you install a sand filter in an above ground pool?

6:2212:15Upgrading the Pool Pump DIY with sand filter - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace. And as before I'm just putting the sand filter holder underneath the pump in that slot. AndMorePlace. And as before I'm just putting the sand filter holder underneath the pump in that slot. And then we're going to put the sand filter on top of that holder.

How do you use a sand filter for an above ground pool?

0:3212:37How to use your Swimming Pool Sand Filter | In-Depth Operational GuideYouTubeStart of suggested clipEnd of suggested clipThe water goes then through the laterals. And then the clean water goes back up the pipe. And thenMoreThe water goes then through the laterals. And then the clean water goes back up the pipe. And then returns back to the pool. And that's how the water is running when it's in filter.

How do you hook up a sand filter to an Intex pool?

3:265:10EASY UPGRADE- SAND FILTER - SALTWATER SYSTEM - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey connect right into the valve here and you could turn the water on and off with these valves.MoreThey connect right into the valve here and you could turn the water on and off with these valves.

When installing a pool sand filter, do you connect it to the pump?

When installing the pool sand filter, you will connect it right after the pump. Pool water will come in through the pool pump, be filtered through the sand filter and released to the chlorinator before returning back to the pool.

How much space between pool sand and filter?

Pour sand carefully into the pool sand filter until laterals are fully covered. For this unit 3 bags should leave at least 6" space between the top of the sand and the top of the filter. Level sand as you pour and make sure the center pipe remains centered in the opening. Be careful when leveling the sand that you do not lift the pipe and lateral assemble up off the bottom of the tank. You will not be able to push the pipe back down without causing the laterals to rotate up.

How high should a pool filter be?

The pool filter should be installed on a level concrete slab not more than 6 feet above the pool water level. Position the pool sand filter so that the piping connections, multiport valve and drain are convenient and accessible for operation and maintenance. Place the filter next to pump.

How to check sand pressure in pool pump?

Turn the pool pump ON. This is the normal operating mode for your filter. Note the pressure gauge reading. This is your clean sand filter pressure. As contaminates build up and clog your sand the pressure will climb. When it is 8-10 psi above your clean filter reading, it's time again to backwash your filter.

How to make a sprite?

Gluing is a two-step process. First apply a thin but even coat of purple primer on each surface to be joined: the outside of the pipe and the inside of the adapter. After the primer dries, apply a thin even coat of glue to both surfaces. Immediately push the pipe all the way into the adapter and twist 1/4 turn to spread the glue. Wait 30 seconds for the glue to set .

How to prevent sand from entering laterals?

Make use the pipe is centered in the opening. Tape the top of the pipe to prevent sand from entering and clogging the laterals.

How much sand do you need for a Hayward S180T?

Before starting the installation, you will need to purchase sand. Use only high rate No. 20 Silica Sand. An example is pictured at left. Check the manufacturer to determine the amount required. This unit (Hayward S180T) uses 3 50 lb bags of sand - 150 lbs total. You can also purchase our superior to sand Click here for our Sand Alternative.

How to operate a sand filter?

Rotate the lever on the above-ground sand filter to the “filter” position. Turn on the pump to operate the filter and pump normally.

How to tighten sand filter hose clamps?

Use a screwdriver to tighten the hose clamps, securing the hose to the skimmer and pump. Connect another hose to the outlet port on your pump. Connect the other end of this hose to the inlet port on your sand filter. Tighten the hose clamps with the screwdriver.

How to attach pool hose to skimmer?

Slide hose clamps onto each end of your flexible pool hose. Connect one end of the pool hose to the bottom of the skimmer and the opposite end to the inlet port on your pump. Use a screwdriver to tighten the hose clamps, securing the hose to the skimmer and pump.

How to backwash a pool pump?

Turn on the pump’s circuit breaker. Move the lever on the sand filter to the “backwash” position. Turn on the above-ground pool pump. Allow the pump to run for about two minutes to remove any impurities from the silica sand in the filter. Turn off the pump.

How to clean sand from above ground pool?

Turn on the pump ’s circuit breaker. Move the lever on the sand filter to the “backwash” position. Turn on the above-ground pool pump. Allow the pump to run for about two minutes to remove any impurities from the silica sand in the filter. Turn off the pump. Move the lever on the filter to the “rinse” position.

Can a pump be hardwired?

Pumps can be hardwired to the breaker, or plug into an outdoor receptacle. You may have a separate switch that operates the pump. Regardless of how your pump connects to the circuit, turning off the breaker ensures the electricity is disconnected and allows you to connect the pump to the filter safely.

What are the ports on a pool pump?

The ports on the valve will be labeled PUMP, RETURN and WASTE/BACKWASH. The PUMP port will be connected to the discharge port on the pump and the RETURN port will be connected to the pool’s return. The WASTE port will be connected to a backwash hose (sold separately).

How long to leave a pump on for a septic system?

After a few minutes (or hours) turn off the pump and switch the valve to “BACKWASH” then turn the pump back on. You will leave it on this cycle for 3-5 minutes.