How to install a Hayward Aqua rite salt chlorine generator?
How to Install a Hayward Aqua Rite Salt Chlorine Generator. 1 Step 1. Balance the pool water before installing the Aqua Rite Salt Generator. Note: If the pool does not have new water, add one quart of metal ... 2 Step 2. 3 Step 3. 4 Step 4. 5 Step 5. More items
How do I choose a cell for my Aqua rite chlorinator?
Aqua Rite chlorine generators operating with software version 1.50 or later are designed to use one of 3 different chlorinator cells that are available from your authorized Hayward dealer. These cells are not included with the Aqua Rite and must be purchased before installation. Choose the appropriate cell based on the size of your pool.
How do I Reset my Aqua rite chlorine generator?
Aqua Rite Chlorine Generator Reset 1 Press the featured diagnostics button five to show an instant salt level 2 Relax and allow the number to settle 3 Cycle slide prime switch from the auto chlorinate. 4 Switch off the unit to reset and then turn it back to auto 5 Wait for like five to seconds for the relay to click.
Do we need to replace the cell in our aquarite chlorine generator?
We need to replace the cell in our Aquarite Chlorine Generator. We currently have a T-9 cell. The pool store site states that a T-9 cell "requires software revision 1.5 for AquaRite or 4.2 for AquaLogic or newer to be compatible."
How do you install a chlorine generator?
0:388:24How To Install Your Hayward Salt And Swim Chlorination System - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat you have at least 10 inches of straight pipe between the last piece of equipment installed onMoreThat you have at least 10 inches of straight pipe between the last piece of equipment installed on your pool pad and your pool.
Which direction does the salt cell go?
0:203:30How to Replace your Hayward Aqua Rite Turbo Cell - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo this is a T 15 cell. Right here and this is also T 15 cell. So this one's going to fit in and itMoreSo this is a T 15 cell. Right here and this is also T 15 cell. So this one's going to fit in and it goes you can put it in the same direction.
How do you install a Hayward Aqua Trol salt chlorine generator?
1:3712:36Hayward Aqua Rite - Installation & Start-Up - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe data wire with a hayward control. System such as a Pro Logic aqua.MoreThe data wire with a hayward control. System such as a Pro Logic aqua.
How do you install Aqua Rite salt?
0:239:23How to Install a complete AquaRite System - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd read your installation manual before beginning the control panel can be installed either on aMoreAnd read your installation manual before beginning the control panel can be installed either on a wall adjacent to the pool equipment or on conduit directly above the existing timer.
Can a salt cell be installed backwards?
The direction doesn't matter.
How do you use aqua rite electronic chlorine generator?
1:203:50AquaRite Settings and Frequently Asked Questions - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress the diagnostic button four times. You'll notice the value changes has the dial is adjusted.MorePress the diagnostic button four times. You'll notice the value changes has the dial is adjusted.
How do you install a salt chlorinator for an above ground pool?
Process To Install Salt System for Above Ground PoolStep 1: Choosing The Right Salt Chlorinator. It is recommended to use at least a salt system that is at least 1/3 larger than your pool size. ... Step 2: Install The Salt System. Unplug all the pool components and locate the filter pump. ... Step 3: Know Salt Level and Add Salt.
Does the flow switch go before or after the salt Cell?
For optimal results, the flow switch should be installed correctly: the flow switch MSUT be installed before the electrolysis cell. Make sure no other components are installed between it and the cell. The flow switch should be installed horizontally and MUST not be installed upside down.
How do you wire a Hayward Aquarite?
2:285:22How To Wire a Hayward AquaRite on 115V - YouTubeYouTubeStart of suggested clipEnd of suggested clipThrough on one 15 voltage you'll typically have three wires you'll have a black hot line you have aMoreThrough on one 15 voltage you'll typically have three wires you'll have a black hot line you have a white neutral line and agreeing for the ground.
How do you set up a salt chlorinator?
0:254:14CORE-Series | The EASIEST Pool Salt System Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipRemember guys this is one of the most advanced salt water chlorinator is out right now and it'sMoreRemember guys this is one of the most advanced salt water chlorinator is out right now and it's incredibly simple to install let's get to work and find out you're going to want to make sure you have
How do you install a Pentair salt chlorinator?
1:1711:49How To Install a Pentair Intellichlor Salt System - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe power center should be at least 8 feet away from the pools edge and also the salt cell comesMoreThe power center should be at least 8 feet away from the pools edge and also the salt cell comes with 15 feet of cable.
What should pool chlorinator be set at?
Try to maintain a consistent salt level of between 2,700 parts per million (ppm) and 3,400 ppm, with 3,200 ppm being ideal.
How long does it take for salt to dissolve in Aqua Rite?
Keep this in the "Off" position until the salt is completely dissolved. This may take 24 hours.
How to connect a salt cell to a flow switch?
Connect the salt cell and flow switch by gluing a short piece of schedule 40 pipe between the two. Make sure the arrow of the flow switch is pointing in the direction of the flow of the water. Gluing is a two step process. First apply a thin but even coat of purple primer on each surface to be joined: the outside of the pipe and the inside of the union/flow switch. After the primer has dried, apply a thin even coat of glue to both surfaces. Immediately push the pipe all the way into the union/flow switch and twist 1/4 turn to spread the glue. Hold the pipe in place for 30 seconds until the glue sets. Note: 2" pvc will not require a reducer but 1.5" will require a reducer on the flow switch and salt cell.
What kind of salt should I use for a pool?
The next steps will involve adding the salt to the pool. It is important to use only sodium chloride (NaCl) salt that is greater than 99% pure. This is common food quality salt or water softener salt and is usually available in 40-80 pound bags. DO NOT use rock salt, salt with yellow prussiate of soda, salt with anti-caking additives, or iodized salt.
How to connect 220V to 110V?
Connect the individual lines to the correct terminals. For 220v, connect the ground line to the green screw, the black to terminal one, and the white to terminal four . For 110, the jumpers most be moved and then the wires can be connected in the same order.
Where is the ground line on a motor?
The external ground line is located on top of the motor . The external ground line for the motor may have a protective green sleeve. Remove an inch of the green sleeve so that the copper line is exposed. The two lines must be touching in order for the system to be properly grounded.
Can you mount an Aqua Rite salt cell inside a panel?
Note: It is important not to block the four sides of the control. DO NOT mount the Aqua Rite inside a panel or a tight enclosed area.
How long does it take for salt to dissolve in Aqua Rite?
Keep this in the "Off" position until the salt is completely dissolved. This may take 24 hours.
How to connect a salt cell to a flow switch?
Connect the salt cell and flow switch by gluing a short piece of schedule 40 pipe between the two. Make sure the arrow of the flow switch is pointing in the direction of the flow of the water. Gluing is a two step process. First apply a thin but even coat of purple primer on each surface to be joined: the outside of the pipe and the inside of the union/flow switch. After the primer has dried, apply a thin even coat of glue to both surfaces. Immediately push the pipe all the way into the union/flow switch and twist 1/4 turn to spread the glue. Hold the pipe in place for 30 seconds until the glue sets. Note: 2" pvc will not require a reducer but 1.5" will require a reducer on the flow switch and salt cell.
What kind of salt should I use for a pool?
The next steps will involve adding the salt to the pool. It is important to use only sodium chloride (NaCl) salt that is greater than 99% pure. This is common food quality salt or water softener salt and is usually available in 40-80 pound bags. DO NOT use rock salt, salt with yellow prussiate of soda, salt with anti-caking additives, or iodized salt.
How to connect 220V to 110V?
Connect the individual lines to the correct terminals. For 220v, connect the ground line to the green screw, the black to terminal one, and the white to terminal four . For 110, the jumpers most be moved and then the wires can be connected in the same order.
What is an aquarite generator?
Aqua Rite is an auto chlorine generator for cleaning pools, and its operation needs a low concentration of sodium chloride in the pool water. These values are pretty low to the extent that they cannot be tasted.
What is Aqua Rite?
Aqua Rite is always on and usually attached to an allotted switch in systems with automation control. Ensure that the switch is not turned on and is placed in the ON section.
What is an aquarite display board?
The AquaRite display board, otherwise called PCB, is the display board for swimming pool chlorine generation systems. The display board clings to the main printed circuit board in the AquaRite chlorine generator power center to show the pool water’s mineral and salt levels.
Why does my Aqualrite board fail?
The AqualRite board failure is usually due to sacrificial malfunctioning of the varistor, thermistor, or fault from the fuse made to safeguard the circuit high-power voltage and current spikes that can occur after lightning or other voltage spikes.
Can chlorine be used to disinfect a pool?
The precise amount of chlorine needed to disinfect the pool depends on the temperature, rainfall, and bather load. This device is not recommended for generating bromine. It operates on 1.50 software versions or is eventually designed to utilize one of the three different cells manufactured by your authorized dealer.
Step 1: Adjusting Salinity (Salt) level
Before the chlorine generator can be calibrated correctly, the salinity—or salt level in the pool water—will need to be at the correct level. For these systems, it should ideally be between 3200-3600 ppm (parts per million). This can be tested using a salt test meter or salt test strips.
Step 2: Locating the Calibration Screen
Once the salinity is adjusted to optimal level, the calibration process can begin. With the pump running and unit set to "Auto" position, press the "Diagnostics" button five times. The screen should display " - 0".
Step 3: Setting the Salinity Level
This step can get tricky and may need to be repeated. While on the calibration screen and with the pool pump still running, push the "Auto" switch down to the "Off" position for two seconds.
More About the Calibration Process
Step 3 takes some practice as it counts down very quickly. For example, if the salinity level in the pool water is 3300 ppm, when the switch is pushed from the "Off" position up to the "Auto" position, after 10 seconds, it will display a set of numbers that start going down immediately. It might start at, say, 4800 (could be higher or lower).
Questions & Answers
Question: My control board shows 3,500, but two independent tests say 2,700 and zero chlorine, and cell tests say it’s good. Which one is correct?
