Project Instructions
- Step 1. Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should...
- Step 2. Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole. Then compact and level the gravel...
- Step 3. Set the post into the hole and attach 2x4 braces to adjacent sides of the post.
- Step 5.
How to mix Quikrete concrete?
How to Mix QUIKRETE Concrete by Hand: This video shows you how to mix concrete by hand, using QUIKRETE Concrete Mix, a wheelbarrow and water. QUIKRETE® concrete mixes can be successfully mixed by hand or machine mixed. For smaller projects, hand mixing is often the best method, and QUIKRETE makes it easy!
How do you lay Quikrete gravel?
Check the forms for level (¼ inch for every 12 feet is sufficient to allow for rain run-off). Patio and sidewalk forms should slope evenly away from structures. Evenly spread 3 to 4 inches of QUIKRETE All Purpose Gravel and then level the gravel. Compact the gravel base using a tamper.
How much water do you put in a Quikrete hole?
You will need 3 quarts (2.8 liters) of water for every 80 pounds (36.3 kilos) of Quikrete concrete. At this point, you can also stir in some liquid cement coloring. 4 Pour two-thirds of the water into the hole you made.
How many cubic feet are in a bag of Quikrete?
One 50-pound bag of Quikrete Fast Setting Concrete Mix yields about.375 cubic feet. For example, if you need to cover 33.333 cubic feet, using 60-pound bags of concrete, divide 33.333 cubic feet by.45 cubic feet to get 74.07 total bags of concrete.
How do you put down Quikrete?
Evenly spread 3 to 4 inches of QUIKRETE All Purpose Gravel and then level the gravel. Compact the gravel base using a tamper. TIP: a solid sub-base will help prevent erosion and slab settling. Dampen the gravel base using a garden hose to prevent shrinkage cracking especially in hot temperatures.
Can you just pour water on Quikrete?
With Fast-Setting Concrete there is no mixing or tools required – You simply pour the dry mix right from the bag into the hole, then add water. Fast-Setting Concrete sets in about 20 minutes so you can quickly move onto the next step of your outdoor project.
What is the best way to mix Quikrete?
0:281:34How to Hand Mix QUIKRETE® Concrete - YouTubeYouTubeStart of suggested clipEnd of suggested clipWork the mix with a hoe gradually adding water until the mix reaches a uniform workable consistency.MoreWork the mix with a hoe gradually adding water until the mix reaches a uniform workable consistency.
Can you put Quikrete on dirt?
Long story short, yes you can pour concrete over dirt.
What happens if you add too much water to Quikrete?
NOTE: the more water that is added to the mix the weaker it becomes; adding one extra quart of water per 80 lb bag can reduce the strength of the concrete by up to 40%.
Is Quikrete as strong as regular concrete?
Quikrete fast setting concrete is just as strong as regular concrete. Concrete gets its strength from a chemical reaction that occurs over time during curing. After it's had time to cure, which usually take 28 days to complete, Quikrete can reach strengths up to 5000 psi.
Can I mix Quikrete in a 5 gallon bucket?
It can be mixed in a 5 gallon bucket, a wash tub, or on a plastic sheet or a tarp. When you're getting your hands in the mix like this, be sure to wear thick gloves. Concrete is caustic and thinner gloves will rip too easily. It helps to have a hand trowel or a small shovel to scrape the sides and bottom of the bucket.
How long does Quikrete take to set?
QUIKRETE® Fast- Setting Concrete sets in approximately 20 to 40 minutes. Heavy objects, such as basketball backboards, may be hung from the post in 4 hours. (If the temperature is below 72 degrees, additional time for curing will be required.)
Can you just pour dry concrete then add water?
Fast-setting concrete is ideal for setting posts because there's no mixing—you simply pour the dry concrete from the bag right into the hole, then add water.
Do you need rebar for 4 inch slab?
For 4” concrete slabs used for driveways and patios, #3 rebar is common. Driveways that will support daily traffic by heavy trucks frequently use 1/2″ or #4 steel bar.
Can you pour quikrete dry?
The concrete mix can be poured dry right out of the bag directly into the hole. Then water is added on top which activates the cement and hardens the mixture.
Can you pour concrete without rebar?
Rebar is not necessary for every concrete project. The general rule of thumb is that if you are pouring concrete that is more than 5 inches in depth, you are probably going to want to add in some rebar to help reinforce the entire structure.
Can you pour wet concrete on dry concrete?
Concrete does not adhere to: Concrete – Dried concrete doesn't have any natural bonding agents, so in order to get wet concrete to bond to existing concrete, a bonding agent will need to be used.
What happens if cement powder gets wet?
On contact with moisture in your mouth, cement and concrete dust forms a corrosive and highly alkaline solution. We cover this in more detail in the skin section below, but if you don't want this dust on your skin, you are not going to want it in your mouth, nose or lungs either!
Can you pour dry concrete then add water?
Fast-setting concrete is ideal for setting posts because there's no mixing—you simply pour the dry concrete from the bag right into the hole, then add water.
Is concrete ruined if it gets wet?
Pouring concrete in the rain can compromise its strength, increasing the tendency for dusting and scaling to develop. Once the damage is done, it can be hard to rectify and will often ruin the appearance of the finished surface. Don't let it rain on your parade.
How to screed concrete?
The surface of the concrete should be relatively flat and slightly above the form. Screed the concrete using a straight 2x4 by moving the board back and forth across the surface of the concrete in a sawing motion to remove the excess concrete and smooth the surface. Add concrete to any low areas and screed level.
What to wear when working with cement?
When working with cement-based products, always wear eye protection and waterproof gloves.
How long does it take for concrete to cure?
Freshly placed concrete should be water cured for a minimum of 3 to 5 days with a fine water mist. TIP: water curing can be eliminated by applying QUIKRETE Acrylic Concrete Cure & Seal immediately after finishing the concrete. Acrylic Cure & Seal can be applied with a roller, garden sprayer or a brush.
How high should a concrete mound be?
Pour the concrete mix in evenly placed leads; the top of the concrete mounds should be about 2 to 3 inches above the forms before leveling. Consolidate and distribute the concrete evenly using a hoe. The surface of the concrete should be relatively flat and slightly above the form.
How to mix Quikrete?
Put the desired amount of Quikrete mix into a wheelbarrow or mortar tub, and make a hole in the middle. You can make the hole using a shovel or a hoe. This will make mixing the concrete easier. If you decide to mix in a mortar tub, bring the tub as close as possible to where you will be spreading the concrete.
What is Quikrete concrete?
Quikrete is a packaged concrete mix that can be used by homeowners and contractors alike in renovating, construction, and landscaping projects. There are many different types of Quikerete products, but concrete and mortar are the most common. You can mix them either by hand or by using a mixing machine. Steps.
How much water do you need to make a concrete slab?
Calculate how much water you will need for your project. You will need 3 quarts (2.8 liters) of water for every 80 pounds (36.3 kilos) of Quikrete concrete. At this point, you can also stir in some liquid cement coloring.
How to get rid of dust on concrete?
Put on a pair of safety goggles and some waterproof gloves. Even if you are very careful, there is still a chance that some dust might get onto your skin. Concrete is caustic, and it can burn your skin. ...
How many quarts of water for 80 lb mortar?
Calculate how many bags of mortar and water you will need. One 80-pound (36.3-kilo) bag will need 5 quarts (4.7 liters) of water. If you will need more mortar for your project, then you will have to adjust the water accordingly.
How long to mix mortar and water?
Add the mortar mix into the water, and mix it for 1 minute. If you are using a mixer, simply turn it on and let it run. If you are doing this by hand: brace your foot or knee against the side of the plastic tub. Stick the blade of the hoe into the mortar, and drag it towards yourself.
How to mix water and concrete?
Use a hoe to mix the water and concrete together. Brace your knee or foot against the side of the mixing container and place the blade of the hoe into the concrete. Drag the hoe towards you.
How to measure for concrete stepping stones?
If you want to use a plastic storage box as a form for stepping stones, measure the length and width of the box and use the desired stepping stone thickness, usually about 2 inches, for the height measurement rather than measuring the entire box height.
How many cubic feet of concrete is in a bag?
Divide the total cubic feet needed by the total cubic feet that can be made from one bag of Quikrete Concrete Mix. Quikrete's Concrete Mix yield's about .15 cubic feet for every 20 pounds of mix, so a 40-pound bag yields .30 cubic feet, 60 pounds of concrete mix yields .45 cubic feet and an 80-pound bag yields .60 cubic feet. One 50-pound bag of Quikrete Fast Setting Concrete Mix yields about .375 cubic feet. For example, if you need to cover 33.333 cubic feet, using 60-pound bags of concrete, divide 33.333 cubic feet by .45 cubic feet to get 74.07 total bags of concrete.
Can you refund Quikrete?
Home improvement retailers who sell Quikrete brand concrete mix gladly refund your money if you purchase more Quikrete than required for a project, but you can save yourself the time, gas money and effort if you calculate the amount of Quikrete needed before you begin the project .
How to mix Quikrete concrete?
Mix one bag of Quikrete concrete in a bucket or wheel barrel according to directions on the bag. Use a shovel to scoop concrete into the Walk Maker mold. Be sure to press Quikrete deep into the corners to fill the mold completely.
What is a Quikrete walk maker?
The Quikrete Walk Maker is a concrete mold that makes it very simple to create your own DIY concrete pavers for a patio or path. We used the country stone pattern to create a patio in our backyard. Here are the basic instructions on how to use the Quikrete Walk Maker concrete molds.
How to make a walk maker out of concrete?
Always wear eye protection + a mask when dealing with concrete. Level the surface where the walk maker will go. Remove grass and clear the area. Place the walk maker mold on the ground and make level. Starting in a corner is easiest. Mix one bag of Quikrete concrete in a bucket or wheel barrel according to directions on the bag. ...
