Position the box around the post in order to make sure that the pieces of scrap wood are underneath the joist. Secure or attach the box to the ceiling with the help of nails through those pieces from below into the joist. Fasten the 4th piece of oak plywood with the help of glue & nails to finish the box column.
Full Answer
How do you make a box out of a column?
Build a U-shaped box with 3 sides and secure it well with screws. Hold the box around the column, then screw the fourth side to create a 4-sided box. The shims need to be installed on the bottom or at the top of the box tightly with a hammer to prevent it from moving. Drill a hole on each side of the box 2 feet from the bottom.
How do you cover basement columns with wood?
To prepare your basement columns to be covered with the wood of your choice, follow these steps. Measure the height of the columns. Make sure your 4 pieces of 1x6x12-inch lumber match those measurements. Build a U-shaped box with 3 sides and secure it well with screws.
How do you add siding to a porch post?
Repeat column wrap steps on the top portion of the porch posts. After the bottom portion is done, you can move up to the top. Repeat the same steps of adding the siding to all sides of the porch posts & trimming it out on the corners and top/bottom.
How do you make a column out of nails?
Nail all four sides on the bottom of the column attaching the blocking pieces underneath. Nail up the sides along the edges. At the bottom and top of the column shaft, add trim pieces. Cut eight pieces of a 1x8 to 8” length. Nail each piece around the base and top of the column.
How to make a 4 sided box?
How to make a wooden box look like a table?
How many holes do you need to drill in a box?
Can you use spray foam on a box?
See 1 more
About this website
How do I cover posts with columns?
0:145:42EASY, DIY FRONT PORCH COLUMN/POST WRAPS TUTORIAL!YouTubeStart of suggested clipEnd of suggested clipSo for starters I'm making my carcass or my enclosing for the wrap. And I'm making them two and aMoreSo for starters I'm making my carcass or my enclosing for the wrap. And I'm making them two and a half feet long from the bottom to this for four by one and for six. Bones.
How do you make a post cover?
1:016:12How to Wrap Posts in Cedar Wood | Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight here. And subtract the width of this board from that and then we'll cut a four by four basedMoreRight here. And subtract the width of this board from that and then we'll cut a four by four based off of those dimensions. So we have an inch and 3/4. Then we're going to subtract.
How do you wrap a support post?
1:202:59Restoration Millwork - Column Wraps - YouTubeYouTubeStart of suggested clipEnd of suggested clipOpen the wrap by peeling back the four pieces of tape halfway. Do not fully remove the tape. As itMoreOpen the wrap by peeling back the four pieces of tape halfway. Do not fully remove the tape. As it is used to hold the corner together for gluing wrap the column around the post.
How do I make my own column wraps?
2:575:05How To Build A Porch Column Wrap | This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you've already cut those away just cut these out. And we created a shiplap spline yeah so it'sMoreSo you've already cut those away just cut these out. And we created a shiplap spline yeah so it's going to go back in again. However after we slide the cap over the top all right coming up to you.
How do you cover a column with wood?
Step 1: Cut Boards to Length.Step 2: Cut and Install Bottom Blocking.Step 3: Cut and Install Top Blocking.Step 4: Nail On the 1x6s.Step 5: Add Decorative Trim.Step 6: Seal Gaps.Step 7: Prep and Paint.
How do you wrap a 4x4?
0:314:26How to wrap porch columns - YouTubeYouTubeStart of suggested clipEnd of suggested clipI again clamp the cord to the post. And make sure everything is level and then I finished markingMoreI again clamp the cord to the post. And make sure everything is level and then I finished marking out where I need to put my spacer. Next I nailed the door into place through the spacers.
What kind of wood do you use to wrap porch columns?
Almost any type of wood works fine for square or rectangular columns. For economy or paint-grade, use fir or yellow pine. For high-end columns, use hardwoods such as birch, mahogany or white or red oak. As with any type of exterior wood, proper sealing and maintenance is required.
How do you cover a support beam?
A drywall cover makes the beam virtually disappear into the ceiling, making it look more like a soffit than a beam. Secure the drywall directly to the beam, tape and cover all the nails and corners. Add texture with drywall mud to match the ceilings and walls. When dry, paint the beam to match the ceilings and walls.
How do you cover a 4x4 porch post?
0:1423:59Fun and Easy DIY Front Porch Post/Column Wrap - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight the two pieces of wood on every edge. Right here rip these down corner of them miter themMoreRight the two pieces of wood on every edge. Right here rip these down corner of them miter them together.
How do you build a column molding?
4:025:44How to Build a Columned Room Divider | This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipMeasure from the top of the cabinet to the ceiling. And cut four column panels to fit slip one panelMoreMeasure from the top of the cabinet to the ceiling. And cut four column panels to fit slip one panel into position between the ceiling. And the top of the cabinet. And clamp it to the blocking.
How can I cover my existing porch columns?
1:067:22Budget Friendly Porch Column Wraps - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we decided to do a veneer over the existing columns. And headed to the hardware. Store we foundMoreSo we decided to do a veneer over the existing columns. And headed to the hardware. Store we found these pvc boards. And they are waterproof. So they're really great for exterior.
How do you wrap columns with PVC boards?
1:413:28How to Install a PVC Column Wrap - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor best results start at the bottom of the three panel column wrap and work upward after assemblingMoreFor best results start at the bottom of the three panel column wrap and work upward after assembling column wrap wipe excess adhesive off with a clean rag. Then.
How do you wrap a basement post?
0:002:35COVER BASEMENT SUPPORT POLES OR LALLY COLUMNS ...YouTubeStart of suggested clipEnd of suggested clipNow cut the wrap to length using a fine-tooth handsaw or miter. Saw for the width take the cut offMoreNow cut the wrap to length using a fine-tooth handsaw or miter. Saw for the width take the cut off and wrap it around the column and Mark the v-groove seam just pass where it overlaps.
How do you wrap aluminum post?
4:0519:31Fantastic PORCH UPGRADE! Installing AFCO Aluminum Column ...YouTubeStart of suggested clipEnd of suggested clipSo you put these four sides together called staves you put the first three together and then kind ofMoreSo you put these four sides together called staves you put the first three together and then kind of fit it around the post.
How do you wrap a flashing post?
2:324:09Aluminum Column Post Wrap Installation - Part 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere we can show you how to staves snap together on the round fluted. System you can see you have aMoreHere we can show you how to staves snap together on the round fluted. System you can see you have a male and a female side.
How do you wrap a stone post?
1:583:37Ply Gem Stone Durata EZ Column Wrap - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace one of the four pieces square with the post. And screw the met anger attached to the stone.MorePlace one of the four pieces square with the post. And screw the met anger attached to the stone. Into the post. Once. The first piece is installed. Run adhesive along the stone offset.
Square Boxouts for Columns| Concrete Construction Magazine
At a seminar on floor construction it was said that diamond shaped boxouts around columns are better than circular. Why should this be so? By diamond-shaped boxouts we presume you mean square boxouts rotated 45 degrees with respect to the column faces.
How to Box in a Pole in a Basement | eHow
If you'd like to transform your basement into a finished recreation area or you simply want to cover up some unsightly poles, box-framing your basement poles is the way to go. By building a wooden box, or frame, around each pole, you can then cover the poles with drywall material.
Mounting electrical box to lally column? - Google Groups
Hi Folks. I am in the process of wiring a basement workshop. I hope to have some 110 volt and 220 volt receptacles mounted on steel lally columns which hold up the first floor.
How to make a 4 sided box?
Build a U-shaped box with 3 sides and secure it well with screws. Hold the box around the column, then screw the fourth side to create a 4-sided box. The shims need to be installed on the bottom or at the top of the box tightly with a hammer to prevent it from moving.
How to make a wooden box look like a table?
Use wood paneling to cover the box and secure the panels with small finishing nails. Install a baseboard around the bottom and a crown on top to finish the look. Add a shelf to make it look like a table. Drywall can also be installed on the box and painted to look smooth and fresh.
How many holes do you need to drill in a box?
Next, drill another set of holes in the middle and yet another set 2 feet down from the ceiling. You will have drilled 12 holes upon completing this step.
Can you use spray foam on a box?
The foam will harden and keep the box wrapped around the column. Wait a day to remove the shims. Use hard-dry foam, not non-expanding foam. Use screws to put the box together, not nails. Nails come loose easily under the pressure of the foam.
Step 1: Cut Boards to Length
Cut four 1x6 boards to length based on the ceiling height. These will be the column shaft.
Step 2: Cut and Install Bottom Blocking
Cut four pieces of the 1x1 to 1-1/2”. Center each piece on the inside bottom of each 1x6. Nail the blocking to the 1x6. Test fit that the four pieces will connect and wrap snugly around the column. The blockers should butt against the existing column and also touch each other.
Step 3: Cut and Install Top Blocking
Cut two pieces of the 1x1 to 5-1/2”. Nail each piece to opposite sides of the soffit, butting them against the existing column. Make sure the blocking is attached to the exact spot you want the columns to be.
Step 4: Nail On the 1x6s
Mina Starsiak of Good Bones partners with Lowes. Not to be used for alternative clients/purposes.
Step 5: Add Decorative Trim
Mina Starsiak of Good Bones partners with Lowes. Not to be used for alternative clients/purposes.
Step 6: Seal Gaps
Mina Starsiak of Good Bones partners with Lowes. Not to be used for alternative clients/purposes.
Step 7: Prep and Paint
Sand rough edges until smooth. Prime and then paint with an exterior-grade paint.
How to make a 4 sided box?
Build a U-shaped box with 3 sides and secure it well with screws. Hold the box around the column, then screw the fourth side to create a 4-sided box. The shims need to be installed on the bottom or at the top of the box tightly with a hammer to prevent it from moving.
How to make a wooden box look like a table?
Use wood paneling to cover the box and secure the panels with small finishing nails. Install a baseboard around the bottom and a crown on top to finish the look. Add a shelf to make it look like a table. Drywall can also be installed on the box and painted to look smooth and fresh.
How many holes do you need to drill in a box?
Next, drill another set of holes in the middle and yet another set 2 feet down from the ceiling. You will have drilled 12 holes upon completing this step.
Can you use spray foam on a box?
The foam will harden and keep the box wrapped around the column. Wait a day to remove the shims. Use hard-dry foam, not non-expanding foam. Use screws to put the box together, not nails. Nails come loose easily under the pressure of the foam.
