Quick Navigation: How To Make A DIY Floating Mantel
- Plan Your Dimensions
- Cut & Assemble 2x4s
- Mount 2×4 Support To The Wall
- Cut & Assemble DIY Floating Mantel
- Fill MINIMALLY With Wood Filler & Sand Mantel
- Stain Floating Mantel
- Attach DIY Floating Mantel To 2×4 Support On The Wall
- Final Thoughts
How to build a floating mantel?
Steps:
- Cut the top, bottom, middle and side pieces to length. ...
- Brush some glue on the side pieces and secure them to the middle board with a nail gun (or hammer and nails) to form a three-sided frame.
- Place the bottom board on top of the frame and secure it with glue and nails. ...
How to install a heavy slab floating mantel?
- Remove the old mantel
- Add support by drilling holes for lag shields, then install lag bolts into the brick
- Measure carefully and drill corresponding holes for the wood mantel
- Push the wooden mantel carefully into place using wood glue for extra support
- Caulk the seam and allow time to dry before using
How to hang a floating wall mantle?
A floating wall mantle can be an excellent addition to your room or fireplace. Follow the simple steps below to effectively hang a floating mantle on your own. Step 1: Mark Line . Place the mantle against the wall where you want to fix it, and then draw a line on the wall to mark the location.
How to build a fireplace mantel from scratch?
Steps To Building The Fireplace Mantel
- The Planning Phase. With all the required materials in place, you’ll need to begin putting down a sketch of how you want your fireplace mantel to look like.
- The Base or Legs. Fireplace mantel construction begins with the legs. ...
- Putting the Breast Plate in Place. ...
- Installing Molding. ...
- Setting the Mantel Shelf in Place. ...
- Installing Decorative Accents. ...
- The Looks. ...
How thick should a floating mantel be?
A depth of 7 inches is ideal for most mantels, as it allows plenty of room to accommodate decorative objects. Keep in mind that the top and the sides of the mantel should be the same depth.
What type of wood is used for mantels?
Walnut is a popular choice for fireplace mantels. It is a harder and heavier type of wood than most and is extremely durable. The rich dark brown wood is an excellent for an impressive fireplace mantel. Hickory is also a great choice for a fireplace mantel if you are going for a unique look.
How do you make a faux beam mantel?
0:4414:53How To Make A Faux Wood Beam Mantel - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will measure and cut everything to size I have the top and bottom pieces of the faux wood beamsMoreYou will measure and cut everything to size I have the top and bottom pieces of the faux wood beams stacked on top of each other toward. The left we have what will be the front of the beam.
How do you hang a free floating mantel?
2:553:53How to Install a Fireplace Mantel - YouTubeYouTubeStart of suggested clipEnd of suggested clipInto. It's completely Center so let me hold this in place. And you can get the drill. And put theMoreInto. It's completely Center so let me hold this in place. And you can get the drill. And put the four screws in. Finally.
Whats the best wood for a mantle?
Maple. If you want a fireplace mantel shelf that has a light brown color, maple is the right choice for you. It is well known for having tightly packed and very strong grains that can take a lot of pressure and handle sanding and finishing well.
What is the best material for a fireplace mantel?
The best material to make a fireplace mantel out of is stone. Stone is a great material for fireplace mantels because it will never burn, dissipates heat well so it will not get too hot, and it is very easy to clean.
How do you make faux wood beams?
How to Build a Faux Wood Beam With Dimensional LumberAdd the Corner Braces to the Side Boards. ... Add Wood Glue to the Side Boards. ... Attach the Bottom Board. ... Cut the Cleat Board. ... Mount the Cleat Board. ... Sand the Faux Beam. ... Distress the Faux Beam. ... Create Beam Straps.More items...•
What is a GeoCast beam?
This realistic looking dark oak beam is a lightweight design moulded from two separate natural oak beams. GeoCast beams offer many advantages over purely wooden beams due to their newly developed material which is composed of natural inorganic minerals. The beam is non-toxic and unburnable, posing no fire risk.
How do I build a fireplace mantel?
17:4720:37EASY DIY WOODEN FIREPLACE MANTEL - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I screwed it into my fireplace. And I made it make sure it was level and then I took this mantleMoreAnd I screwed it into my fireplace. And I made it make sure it was level and then I took this mantle I lifted it up and I put it on the 2x4. And then screwed it in on the top just three screws.
How far should a mantle stick out?
The building codes will typically determine the height to place the mantel from the hearth, and the distance from the firebox. As a general rule, the mantel is placed about 12 inches above the fireplace opening. Then adding an inch to the distance for every inch that the mantel protrudes.
How much weight can a mantle hold?
Combustible objects placed on or around the mantel must meet your fireplace manufacturer's requirements for clearances to combustibles. DO NOT OVERLOAD MANTEL: THE MAXIMUM LOAD FOR ALL 60 INCH MANTELS is 150lbs. MAXIMUM LOAD FOR ALL 72 INCH MANTELs is 180lbs.
How do you anchor a mantle to drywall?
Holding your drill at a 45 degree angle downward, drill a pilot hole through the shelf and drywall and into the stud. Install a finishing nail into each of the pilot holes with a nail gun or hammer; the nails must be long enough to penetrate at least 1 inch into the drywall. These nails will secure the mantle in place.
What are most mantels made of?
Standalone floating mantels are commonly made from wood, while mantels found as part of a complete fireplace surround can commonly be found made from wood, stone, concrete and marble.
Can you use pressure treated wood for a mantel?
We get this question a lot. The simple answer is yes, pressure-treated lumber can be used in any interior application except cutting boards and countertops.
Is Poplar a good wood for a mantel?
Poplar Wood Fireplace Mantels While poplar in its natural state is light in color and often contains brown or green streaks, it can be easily painted to achieve the desired finish. Our selection of poplar fireplace mantel styles offers an unbeatable combination of stability, aesthetic appeal and affordability.
Is Cedar good for fireplace mantels?
Cedar is a knotty softwood so it's soft enough to work with easily but durable enough for a mantel shelf. Northern white cedar and aromatic red cedar is indigenous to North America and not endangered, so the wood is widely available in several forms suitable for mantel shelves.
Step 1: Measure Fireplace Width
Use measuring tape to determine the exact width of the fireplace. Once measurements are taken, consider adding an overhang by adding an additional 8x12 inches along each end.
Steps 2: Measure, Mark and Miter Fascia
Use a measuring tape and pencil to measure and mark 1x12-foot wood planks to the desired width of fireplace and any additional overhang. Next, cut the fascia to size, mitering each end with a compound miter saw. Finally, place the fascia board on a table saw and miter the entire front edge at a 45-degree angle.
Step 3: Measure, Mark and Miter Top
A depth of 7 inches is ideal for most mantels, as it allows plenty of room to accommodate decorative objects. Keep in mind that the top and the sides of the mantel should be the same depth. First, use a measuring tape and pencil to measure and mark the mantel top to size.
Step 4: Measure, Mark and Miter Sides
The fascia and top will connect to two side pieces, which you'll construct from scrap fascia lumber. The side pieces should be the same depth as the top. Using a measuring tape and pencil, measure and mark the scrap wood to size.
Step 5: Attach Fascia, Sides and Top
Once the fascia, top and side pieces have been cut to size and mitered, they'll need to be assembled to create the boxy form of a modern mantel. Attach these components by adding wood glue along the surface of each mitered edge, then fit the fascia, sides and top together. Next, use a nail gun to secure all pieces to one another.
Step 6: Cut and Attach Reinforcement Blocks
Create mitered reinforcement blocks from scrap wood by running them through the table saw, cutting each at a 45-degree angle. Next, add wood glue along each mitered edge and add one reinforcement block to each 12-inch span of mantel.
Step 7: Spackle and Sand
To achieve a polished, smooth finish, all nail holes and raw edges on the mantel should be filled and sanded before a stain is added. First, fill all holes and imperfections with spackle using a spackle knife. Once the spackle is dry, use a fine-grit sanding block or orbital sander to smooth down the spackle, as well as the wood surface.
Steps
1. Cut the top, bottom, middle and side pieces to length. Pass each board through the table saw with the blade set at a 45-degree angle so the mantel looks like one solid block of wood once they're all attached. 2.
How to Build a New Fireplace Surround and Mantel
A dated fireplace is given a British Colonial look with the addition of staircase posts, molding and a coat of fresh paint.
