While turning on your gas fireplace manually, just follow the following steps:
- To turn on your modern gas fireplace without remote control, first, rotate the gas control knob to the pilot position from the Off position.
- Then press the pilot knob of your gas fireplace. It will circulate and send gas to the ignition system.
- Now, press the igniter switch. Now, keep pushing on the ignitor button until your burner will light. ...
How do I turn my fireplace on and off?
Solution:
- Make sure that the power supply through the main service panel is on.
- You’ll need to access the manual controls. For some models, you’ll have to pull down the grill or remove the glass doors. ...
- Find the manual controls.
- Turn on the main power switch.
- You’ll find a switch marked as ‘ON’. ...
- Press the ON button on the remote control. ...
How do you light a gas fireplace?
To light a gas fireplace that requires the use of a key:
- Thoroughly read the owner’s manual for that particular gas fireplace to understand the correct lighting procedure.
- Locate the gas fireplace key.
- Remove the access cover to the controls.
- Insert the key into the gas fireplace (but don’t turn yet)
- Wear a heat-resistant glove and use a long lighter or match and place the lit end at the burner.
How do I light the pilot on my gas fireplace?
- Turn the knob from the “Off” to the “Pilot” position.
- Push in the pilot knob, which manually sends gas into the system.
- Push the igniter button once every second until it lights. ...
- After the pilot lights, keep the pilot button held down about 15 to 30 seconds to warm up the thermocouple and ensure that the flame stays lit. ...
- Release the pilot knob. ...
Why would a gas fireplace stop working?
Why Would a Gas Fireplace Stop Working?
- Old Batteries. Some gas fireplaces use battery power to start the pilot light. ...
- Closed Gas Valves. Look in your firebox to see if the gas valve is open and set in the “on” position. ...
- Blown Out Pilot Light. ...
- Propane Tank & Natural Gas Line Problems. ...
- Thermocouple and Thermopile Issues. ...
- Thermostat Problems. ...
How do you turn a gas fireplace on without a remote?
Today's modern gas fireplaces are typically controlled with a remote control meaning starting your gas fireplace is as easy as pressing the 'on' button on your remote. Without a remote there will typically be an ignition button on the control panel of the fireplace.
How do you manually turn on a fireplace?
0:333:14How to LIGHT a Gas FIREPLACE - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn. Second thing we want to do is turn our valve to pilot you can see that there's an arrow pointingMoreOn. Second thing we want to do is turn our valve to pilot you can see that there's an arrow pointing to that that says pilot and what you want to do is push down on the knob.
How do you light a pilot light on a gas fireplace without ignitor?
4:167:30How to light a Gas Fireplace pilot light with no ignitor - YouTubeYouTubeStart of suggested clipEnd of suggested clipHold down the knob for one minute I did probably less than ten seconds.MoreHold down the knob for one minute I did probably less than ten seconds.
How do I start my electronic ignition gas fireplace?
0:141:25How to Light the Pilot with a Direct Spark Ignition System - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo refer to your owners manual for detailed instructions. Slide open the bottom faceplate panelMoreSo refer to your owners manual for detailed instructions. Slide open the bottom faceplate panel depressed a gas control knob halfway and turn the knob counterclockwise to the pilot setting depress the
What happens if the pilot light goes out on a gas fireplace?
Can a Pilot Light Outage Be Dangerous? The worry here is that when a pilot goes out, the gas valve that supplies the fuel for the pilot flame could still be pumping gas. This can mean a buildup of gas, and when the pilot is relit or relights itself it could result in a very serious explosion.
Where is the gas shut off valve for gas fireplace?
Gas fireplace: The shut-off for a gas fireplace is typically on the control panel. This control panel can be found behind the front screen, where a knob that controls the flow of gas can be turned to 'off'.
Can I manually light my gas fireplace?
Turn the knob from the “Off” to the “Pilot” position. Push in the pilot knob, which manually sends gas into the system. Push the igniter button once every second until it lights. Depending on how long it's been since the gas fireplace was last used, ignition may take multiple attempts.
Why won't my gas fireplace turn on when I flip the switch?
If the pilot is lit, and you flip the wall switch and the fireplace does not come on, the most common problem is that the control valve is not turned all the way counter-clockwise to the “On” position. Trust me. Nine out of ten times, that's it.
Where is the gas fireplace switch?
First, locate the fireplace controls, they are located usually behind a louver or panel at the bottom of the fireplace. Next, locate the control knob on the gas valve, it usually has 3 labels Off, On, and Pilot. You will also want to locate the ignitor button; it looks very similar to a starter on a barbecue grill.
Do electronic ignition fireplaces have a pilot light?
Flip of a Switch The IPI system does not use a pilot light and instead relies on an electronic ignition switch to light the pilot after flipping on the wall switch or using the remote.
Why does my gas fire not ignite?
If your gas fire doesn't turn on, it may be because the thermocouple isn't quite in the right place and therefore, can't interact with the other components as it should. If the pilot flame sparks but doesn't stay lit, the thermocouple has likely worn out.
Is the pilot light on the gas fireplace always on?
The little flame you see in your gas fireplace after you have turned it off is called a pilot light. A Standing Pilot Light runs constantly, whether your fireplace is on or off.
Can you turn on the electric fireplace without the remote?
As an electric fireplace runs on electricity, it must be plugged into a nearby wall socket, and the socket switched on before the controls on the fireplace can be used to turn on either the flames or the heater.
How do you start a gas fireplace with a key to the wall?
InstructionsLocate Gas Valve Knob. Find the gas valve knob on the wall or floor. ... Open Front of Fireplace. Open up the glass doors or screen to the fireplace.Locate Ignition Area. ... Prepare Ignition Source. ... Place Key in Gas Valve. ... Light Ignition Source. ... Slightly Turn on Gas Valve. ... Turn Gas Valve on Full.More items...•
How do I light the pilot on my old gas fireplace?
Move the pilot knob to the pilot position. This will allow you to push the knob in, which manually releases the flow of gas to the pilot. Now, while holding the pilot knob in, push the igniter button in once every second until the pilot is lit.
How do you use an old gas fireplace?
How to Operate a Gas FireplaceLook over the user manual included with your fireplace. ... Remove your fireplace's outer cover. ... Put a fireplace key into the device's gas valve knob. ... Hold a long lighter up to the burner and ignite it. ... Turn the gas key. ... Replace the fireplace's outer cover immediately.
Where to Find the Gas Valve Knob
The gas valve knob is the junction between the main gas pipe and the gas fireplace. When closed, the gas valve knob acts as a gate to prevent gas from flowing to the fireplace. When opened, gas will flow. The valve can be opened partially or in full.
Safety Considerations
Flammable and potentially dangerous, natural gas is colorless and odorless. To help with detection, gas companies treat natural gas with trace amounts of mercaptan, a pungent odor similar to rotten eggs or sulfur.
Troubleshooting Turning on a Gas Fireplace With a Wall Key
Wall key gas fireplaces do not have pilot lights. Manually lighting the fireplace substitutes for the pilot light. Gas fireplaces that operate with wall switches do have standing pilot lights, though.
Instructions
Find the gas valve knob on the wall or floor. Place the key nearby. Do not place the key in the valve yet.
When to Call a Professional
Call a licensed plumber for any issues relating to the gas line within the house. Not all plumbers are equipped to work with gas lines, so check with them in advance. If you smell a gas leak outside of the house, call the gas company immediately.
How does a gas fireplace work?
A gas fireplace feeds natural gas from a main line into the bottom line of a paneled and insulated fireplace unit. The fireplace is turned on by a pilot light that ignites the gas line under the tempered beads or ceramic logs.
What to do if your gas fireplace is not cooperating?
If your gas fireplace is not cooperating or if you have had it turned off all season, you may be faced with having to figure out how to ignite the appliance to get it to turn on. Once you understand gas fireplace operation, you can flick on the fireplace with confidence and fill your space with heat and light. Advertisement.
Why is my fireplace stalled?
There are a few reasons your fireplace may be stalled: It has been more than six months since it was last used. The lines may be clogged with dust and dirt build-up. The lines that run from the valve to the main line under the ceramic logs could be kinked and slowing down the delivery of gas to the ignitor.
How long does the pilot light stay on in a fireplace?
The pilot light stays on until needed to create the flames in the fireplace at the touch of a button.
How long does it take for a fireplace to click?
If you've heard the click for longer than 10 to 30 seconds, stop and let the lines clear out. Wait at least 10 seconds before trying again. You may have to do this a few times before the fireplace roars to life. Advertisement.
What to do if you have trouble with pilot light starter?
If you are having trouble, grab a flashlight. The pilot light starter tends to be small and unobtrusive.
Do gas fireplaces need electricity?
Advertisement. Modern gas fireplaces have an electronic ignition system that may need a spark of electricity to create a crackling fire. They may come with a backup ignitor that uses batteries rather than electricity.
Video Guide: Starting A Gas Fireplace
The pleasure of having a gas fireplace is unmeasurable ( read more about them here ). There is no need to look for dry wood, carry it home, and chop it up before placing it in the fireplace.
How to operate an electronic pilot in a gas fireplace
Turn on the gas fireplace’s supply line. Ensure the electric switch is on if you have an electronic setting that controls the unit’s temperature. Look for the control knob labeled “pilot ignite.” If you have a unit that enables you to regulate the temperature, it will have: on, off, and electronic settings. Turn it off for a few minutes.
What you should know
If the pilot tube has air in it, it’s difficult to light. However, after numerous tries, the fireplace should ignite. If you notice that the pilot light needs to be lit frequently, check the end of the tube for debris.
Conclusion
The technique for relighting the pilot on your gas-burning fireplace is determined by the type of pilot you have; electronic or flame-lit. It isn’t difficult, but it may be perplexing if you’ve never done it before. The above are steps on how to start a gas fireplace and relight the pilot.
What is a gas fireplace?
Traditionally, gas fireplaces have been manufactured with a standing pilot light that ignites the flames without the use of external electricity. Gas fireplaces that are more recent have an electronic ignition system that needs a spark of electricity to bring the appliance to life with a crackling fire. If you have a newer model, you can buy ...
How long does it take for a fireplace to light up?
If the fireplace hasn't lit up within 10 seconds, wait at least 10 seconds before trying again. It may take a few tries to get the fireplace to ignite. Once the pilot is lit, you can leave the fireplace pilot on and turn the fireplace on and off at the switch, remote or other application. The pilot light can stay lit without heating up ...
Can a gas fireplace catch fire?
When the power is out and heat is an issue, a gas fireplace is a lucky thing to have. The fire can still catch if there is no electricity coming in to your gas fireplace. Be prepared to light up your space and be on the receiving end of warmth if you know how the unit works and how to get the spark ignited.
Can you use batteries on a gas fireplace?
The IntelliFire and IntelliFire Plus use batteries to pilot your gas fireplace during a power outage. If you have a standing pilot, the gas fireplace will light itself without the need for electricity. But the pilot may need to be lit manually on occasion. The manual will have detailed instructions for the standing pilot ...
Do gas fireplaces have pilots?
Igniters and Pilots. Modern gas fireplaces more than likely have an intermittent pilot ignition system. This needs electricity to spark the pilot flame every time you go to use the fireplace. Many newer models, such as the Heatilator lines, have battery backup systems. The IntelliFire and IntelliFire Plus use batteries to pilot your gas fireplace ...
Where is the pilot light located on a fireplace?
Open your control panel to manage the pilot light. It is typically found behind the fireplace screen.
What to do if you smell gas in your house?
If you smell any gas, quickly open the window to air the room out, if there is a strong gas smell then exit the home and call the fire department.
How to ignite a pilot light?
Wear heat-resistant gloves while holding a long lighter or long match to the burner to ignite. Be prepared to quickly move your hand away if the pilot light ignites.
Can you turn off the flame on a gas fireplace?
Many gas fireplaces nowadays have a wall switch that can easily allow you to turn your gas fireplace on or off. It may also allow you to adjust the level of the flame. If it does not light, you may need to manually light the pilot by using the steps outlined below.
