how do you prevent kickback when using a circular saw

Take these specific precautions to help prevent kickback when using any type of circular saw:

• Keep saw blades sharp. ...
• Make sure the blade has adequate set in the teeth. ...
• Keep saw blades clean. ...
• Be very cautious of stock which is pitchy, knotty or warped. ...
• Always hold the saw firmly with both hands.
• Release the switch immediately if the blade binds or the saw stalls.
• Support large panels so they will not pinch the blade. ...

Full Answer

Why does my circular saw kickback?

A circular saw kickbacks when you start cutting your wood piece lying on support irregularly. The ends of wood increase force on the blades. Due to which the blades pinch, while moving forward. Meanwhile, a lot of force is stored with the blades.

How do you prevent saw blade kickback?

This minimizes the amount of saw blade surface exposed and reduces the probability and severity if any kickback does occur. Minimize blade pinching by placing the saw shoe on the clamped, supported portion of the work piece and allowing the cut off piece to fall away freely.

What is an ant-kickback saw blade?

An ant-kickback blade is made much tougher than ordinary circular saw blades and can absorb the impact of the nail. This does not prevent binding or pinching so you should always stay ready.

What causes kickbacks when cutting wood?

Using a saw with unsharpened or pointless blades might be the cause of kickbacks. Using unsharpened blades require more pressure to cut the wood which greatly increase the chances of pinching. The blade might pinch into the wooden boards, causing it to stuck in it.

How can Kickback be prevented?

Follow these tips to reduce the risk of hurting yourself from kickback on a table saw.Have basic safety features in place. ... Never make free-hand cuts. ... Do not crosscut with the rip fence. ... Use a push stick. ... Do not cut crooked stock. ... Check your blade. ... Be attentive.

What causes saw kickback?

Kickback occurs when the teeth of the saw blade, moving at tip speeds of 120 miles-per-hour impart sufficient force to cause the workpiece to move in a violent and unexpected manner. Skil saw kickback tends to throw the saw back at the operator, its blade often running over fingers as it moves backwards.

What device is used behind the blade to prevent kickback?

A splitter is a stationary blade of similar thickness to the rotating saw blade mounted behind it to prevent a board from pinching inward into the saw kerf and binding on the saw blade, potentially causing a dangerous kickback.

When using a circular saw you should never?

Do not use a saw that vibrates or appears unsafe in any way. Do not force the saw during cutting. Do not cut materials without first checking for obstructions or other objects such as nails and screws. Do not carry the saw with a finger on the trigger switch.

Does blade guard prevent kickback?

All SawStop blade guards come with anti-kickback pawls to help prevent kickback of your workpiece. Working with a delicate piece of wood? You can flip them up and out of the way on all blade guards, and also remove them entirely on the Micro Blade Guard. Ketan Khandekar and 13 others like this.

How does anti kickback chain work?

0:027:22Stihl Yellow VS. Green chain for plunge cuts, and me felling a stump ...YouTubeStart of suggested clipEnd of suggested clipIt's going to prevent the cutter from grabbing any embedded object like a nail or a piece of barbedMoreIt's going to prevent the cutter from grabbing any embedded object like a nail or a piece of barbed wire or anything like that.

Why is my circular saw pushing back?

What is kickback? Kickback happens when the saw blade binds or stalls suddenly in the wood and the saw gets driven back toward you. So the key to preventing this is to make sure your blade doesn't bind in the wood.

How do you handle a circular saw?

1:1010:11How to Use a Circular Saw. Everything you need to know.YouTubeStart of suggested clipEnd of suggested clipThe saw with both hands the rear handle has the trigger that you'll hold throughout the cut someMoreThe saw with both hands the rear handle has the trigger that you'll hold throughout the cut some songs have a safety button that you need to press first to prevent accidental.

Should a circular saw have a riving knife?

Riving knife and saw guard Suitable top guards and riving knives should be fitted to all circular saw benches. It is vital that these are properly adjusted for each job being carried out. Machines should be fully enclosed beneath the table.

What are 5 safety rules for operating a circular saw?

What are the circular saw safety tips?Put on safety equipment before handling the saw. ... Do a saw check. ... Learn to hold it properly. ... Use a safe depth of cut settings. ... Only use sharp blades. ... Unplug the saw when not in use. ... Never use a defective saw. ... Do not overreach.More items...•

Should you wear gloves with a circular saw?

Hearing protection may be required due to the extreme noise levels generated, especially during extended use. A respirator or dust mask may be required, depending on the material being cut. Do not wear loose clothing, long-sleeves, or gloves while operating a circular saw.

What precautions should be taken while working on circular saw machine?

keep upper and retracting lower blade guard clean and free of sawdust • do not hold or force the retracting lower guard in the open position. ensure the blade guard is in place and functioning as required by the manufacturer. dust: wear an approved respirator or dust mask • noise: wear appropriate hearing protection.

What causes kickback on a table saw How can this be avoided?

Essentially when a piece of wood touches the blade on an angle or gets bumped out of alignment it catches the blade in the teeth and gets thrown back. The most effective way to avoid kickback on a table saw is by using a riving knife. Most table saws have these installed right behind the blade.

What is kickback when cutting wood?

Woodworking » Kickbacks Kickbacks occur when a saw seizes the stock and hurls it back at the operator. This can happen when the stock twists and binds against the side of the blades or is caught in the teeth.

Why is my circular saw blade stopping?

A Damaged or Warped Blade One of the most common issues that can cause your circular saw to keep stopping is if the blade is damaged, cracked, or warped. If the blade is damaged in any way, no matter if it works or not, you need to get rid of it and get a new blade.

How to control saw?

For maximum control, hold the saw firmly with both hands after securing the work piece. Clamp work pieces. Check frequently to be sure clamps remain secure.

What is a kickback in a tool?

Unplug, clean and store the tool in a safe, dry place after use. Kickback is a sudden reaction to a pinched blade, causing an uncontrolled portable tool to lift up and out of the work piece toward the operator . Kickback is the result of tool misuse and/or incorrect operating procedures or conditions.

Why do saw blades have hollow ground sides?

Some saw blades have hollow ground sides instead of tooth set to provide clearance. Keep saw blades clean. A buildup of pitch or sap on the surface of the saw blade increases the thickness of the blade and also increases the friction on the blade surface.

How to minimize blade pinching?

Minimize blade pinching by placing the saw shoe on the clamped, supported portion of the work piece and allowing the cut off piece to fall away freely .

Why does my blade kick back?

Buildup of sap on the blades, insufficient set, dullness and unguided cuts, can all cause an overheated blade and kickback.

How to tie back long hair?

Tie back long hair. Do not use a circular saw that is too heavy for you to easily control. Be sure the switch turns on properly. Do not use a tool if the switch does not turn it off when returned to the "off" position after release. Use sharp blades. Dull blades cause binding, stalling and possible kickback.

When you start a circular saw, what should you do?

When you start your saw allow the blade to reach full speed before the work piece is contacted. Be alert to the possibility of the blade binding and kickback occurring, (see "preventing Portable Circular Saw Kickback"). If a fence or guard board is used, be certain the blade is kept parallel with it. NEVER overreach!

What is a Circular Saw Kickback?

A kickback refers to the point during the sawing process when the blade of the circular saw gets stuck or the wooden board you’re cutting bows downward. As a result, the blade comes to a halt all of a sudden, and the circular saw is driven back in your direction.

Preventing Circular Saw Kickback – Step-by-Step Procedure

Preventing circular saw kickback involves several safety precautions and technical adjustments of the circular saw itself. Below, we’ll walk you through all the necessary steps.

Final Verdict

Simply put, regardless of whether you’re a beginner or a professional craftsman, the tips provided in this article to prevent a circular saw kickback will help you big time in feeling more secure while carrying out jobs that require the use of circular saws.

How to reduce kickbacks on circular saw?

1. Operating The Saw. The circular saw consists of two handles i.e., front and back. Operating the saw is so simple and probably the most simple and convenient way to reduce kickbacks. While working with the saw make sure that you have a strong grip on both the handles of the saw.

Why does a circular saw kick back?

A circular saw kickbacks when you start cutting your wood piece lying on support irregularly. The ends of wood increase force on the blades. Due to which the blades pinch, while moving forward. Meanwhile, a lot of force is stored with the blades. When the saw cannot bear this force then it comes out in opposite direction of cutting.

What to do if you hear a noise coming from your saw blades?

If you hear any annoying or screechy sound coming from your saw blades, stop doing your work immediately. If you see any wandering from the path that you have drawn, before working, just keep the blades off and start again from the starting points but must check that you are not cutting across one path over and over again.

Why does my saw kick back?

Using a saw with unsharpened or pointless blades might be the cause of kickbacks. Using unsharpened blades require more pressure to cut the wood which greatly increase the chances of pinching. The blade might pinch into the wooden boards, causing it to stuck in it. As a result the higher pressure on the saw may cause it to move backward.

Why does my saw burn on the board?

Overusing a saw results in the overheating of saw blades. Overheating might be the result of using a dull or edgeless blade, extensive rubbing of the saw on the board, using the saw so abruptly or so slowly and improperly adjusted saw. All these things cause greater friction and leave scorch marks on the wooden board.

What happens when a saw cuts in the opposite direction?

Kickback can also occur when the wooden board that you are cutting loops in the downward direction. This squeezes the blades of the saw and it stalls. Suddenly it left off and move towards you which could be dangerous.

What are the causes of kickbacks?

Among all the causes of Kickbacks, following are the common ones: 1. Usage Of Unsharpened Blades.