How do you rebuild a Craftsman chainsaw carburetor?
- Drain the fuel tank.
- Remove the cylinder shield.
- Disconnect the spark plug wire and remove the air filter.
- Remove the carburetor.
- Rebuild the carburetor.
How do you replace fuel lines on a craftsman chainsaw?
Tips on Inserting Fuel Lines in Chainsaw Gas Tanks
- Fuel Line Basics. Chainsaw fuel lines are typically clear plastic tubing. ...
- Proper Tube Length. When it's time to replace the chainsaw fuel lines, it's important that you cut the new tubes to the proper length.
- Tools of the Trade. Using the proper tools for the job makes fuel line replacement easier. ...
- Additional Tips. ...
How to adjust a carburetor in a craftsman?
- Verify carburetor is set to stock settings:
- Start bike, bring to operating temperature.
- Set idle speed adjusting screw, clockwise to increase rpm, counter-clockwise to decrease rpm.
- Adjust idle mixture by turning idle mixture screw slowly clockwise until the engine runs poorly.
How do you adjust the carburetor on a chainsaw?
How do you adjust the carburetor on a Husqvarna 350 chainsaw?
- Locate the idle-speed screw and the idle-mixture screws on the side of the chainsaw.
- Turn both the low- and high-speed screws clockwise to the midpoint.
- Adjust the low-idle screw clockwise and counterclockwise respectively, until you find the highest idling speed.
How to clean and adjust a chainsaw carburetor?
Tools You’ll Need to Buy
- Flathead screwdriver
- Toothbrush
- Compressed air
- Tachometer
How do you rebuild a carburetor on a chainsaw?
6:3611:57How to Fix a Chainsaw Carburetor - YouTubeYouTubeStart of suggested clipEnd of suggested clipI like to do to stay organized is first go through the kit and match up each of the parts that I'llMoreI like to do to stay organized is first go through the kit and match up each of the parts that I'll be replacing. Then I'll just set the old part.
How do you fix a 2 cycle carburetor?
0:1110:30How to Fix a 2-Cycle Engine Carburetor - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey're often two types of kits available a complete rebuild kit or a gasket and diaphragm kit theMoreThey're often two types of kits available a complete rebuild kit or a gasket and diaphragm kit the gasket and diaphragm kit simply includes the two diaphragms.
How do I adjust the carburetor on Craftsman chainsaw?
0:244:13Craftsman 16" chainsaw carburetor adjustment, sim-pul, 1636 poulan.YouTubeStart of suggested clipEnd of suggested clipSo this one fires up you squeeze the trigger bogs out shuts off when it does that it's this oneMoreSo this one fires up you squeeze the trigger bogs out shuts off when it does that it's this one right here you're gonna go in and you're gonna turn it you'll fit you'll feel it go into the cart.
Why does my Craftsman chainsaw keep stalling?
0:052:01Top Reasons Chainsaw Starts, Then Stalls — Chainsaw TroubleshootingYouTubeStart of suggested clipEnd of suggested clipOver time the arrestor can become clogged with soot which may cause the chainsaw engine to stall.MoreOver time the arrestor can become clogged with soot which may cause the chainsaw engine to stall. You can try cleaning the arrestor with a wire brush. But you may need to replace it with a new one.
What is the most common problem with 2 stroke carburetors?
Typical problems include hard starting, rough running, a need to adjust the carburetor during use to keep the engine from stalling, a need to rev the engine to keep it from dying, and not starting at all.
How do you clean a 2 stroke carburetor without removing it?
Vacuum away any loose dirt, dust, debris, grime, and great on the surface with a handheld and cordless vacuum. Lay out rags or cloths at the base of the carburetor to catch runoffs and protect the surfaces. Apply the carburetor and choke cleaner in thin, even coats. Then, wait for it to settle and work its magic.
Why does my chainsaw dies when I give it gas?
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
Why does my chainsaw bog down when I give it gas?
There are several factors may make your saw not work properly. First, it could be that the carburetor, spark arrestor or the air filter are dirty. Or, the carburetor adjustment might have simply slipped. This guide will explore some of the reasons why you chainsaw bogs down as well as the different ways to fix it.
How do you adjust H and L screws on a carburetor?
0:254:29Chainsaw Carburetor Adjustment | How to Tune 'Correctly' - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what we're looking for at this stage then is for both screws to be screwed fully in both the LMoreSo what we're looking for at this stage then is for both screws to be screwed fully in both the L and the H we'll adjust this in a moment this is the idling.
Why does my Craftsman chainsaw dies when I give it gas?
A clogged fuel filter is often caused by leaving old fuel in the chainsaw. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the fuel filter and cause the engine to stall.
Why does my chainsaw start but wont stay running?
Clogged carburettors are one of the most common reasons why a chainsaw won't stay running or start at all. If you haven't used the chainsaw for a long time, it's best to replace the fuel and fuel filter before using it again. Once you have drained the fuel tank, check the fuel lines.
Why does my chainsaw only runs on choke?
When your chainsaw only runs if the choke is on the problem, in most cases, is a result of fuel supply problems or a faulty carburetor. To fix the problem you should check and clean the fuel system and carburator.
How to do a chainsaw overhaul
The most effective inspection and maintenance routine need an overhaul.
How to service a chainsaw carburetor
Most problems in a chainsaw that involves hard starting and low running are caused by the carburetor.
How to remove the carburetor
Servicing a carburetor is quite an easy task: however, it requires some little skillset to pull it off.
How to disassemble a carburetor
You can start disassembling from the diaphragm side so that it can be easy to remember when putting the parts together.
How to the clean the carburetor
There are two known methods for cleaning the carburetor that is the use of a carburetor cleaner and use of the ultrasonic cleaner.
How to rebuild the carburetor
To reassemble the carburetor first, you are required to take the kit and remove all the spare parts available.
How to re-install the carburetor to the chainsaw
With all these parts in place and secured, it’s time to place the carburetor back to the chainsaw.
How to remove air filter from carburetor?
Remove the air filter. Using a 7/16-inch socket driver, remove the 2 mounting nuts that secure the carburetor to the engine. Pull the air filter housing off the carburetor. Pull the carburetor away from the engine block. Be careful.
Why is my chainsaw not running?
If your chainsaw isn’t running well, a dirty carburetor could be the problem. You can take it apart, clean it and rebuild it, using a carburetor rebuild kit. If the engine won’t start even though there’s fuel in the chainsaw, the carburetor could be the problem. Sometimes, it’s easier to replace the carburetor than to clean it and rebuild it.
What to do if your chainsaw isn't running?
By Lyle Weischwill. If your chainsaw isn't running well, a dirty carburetor could be the problem. You can take it apart, clean it and rebuild it, using a carburetor rebuild kit. This repair guide takes you through the process. Repair difficulty.
How to test a carburetor?
If the engine won’t start when the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope.
How to adjust carburetor on chainsaw?
Step 1: First you need a flathead screwdriver that is small enough to fit through the adjustment holes. These are the holes on the carburetor in which you must insert the screwdriver to turn the adjustment screw. Clear the holes of any debris so that you can see the ends of the adjustment screws inside.
What is the adjustment on a chainsaw carburetor?
This is the adjustment on your carburetor that controls exactly how much the throttle valve will stay open when you release the trigger. Basically, it is all about how well your chainsaw idles once you have taken your finger off the trigger.
What are the settings on a chainsaw?
There is an adjustment for the idle speed and the throttle stop, the low-speed fuel adjustment, and the high-speed fuel adjustment. It is important that each one works properly for your chainsaw to run. These adjustments typically come in the form of a screw on your carburetor.
What happens if you don't adjust your carburetor?
If your carburetor is not adjusted properly, you may have too much smoke, not enough power, and this will ultimately cause damage to your engine. If you want your saw to do its job properly, simply follow the easy steps in this guide on how to adjust your chainsaw carburetor. There are three main adjustment settings.
How many RPM should a chainsaw run?
Once the chainsaw is warm, begin the procedure. Step 5: First is the idle speed. Your target should be about 2,700 RPM.
What happens if you adjust your saw too high?
If this adjustment is too high, your saw will not be able to reach the maximum RPM level that it needs to build power to cut. You will also have slow throttle response, the engine will smoke, and the entire piece of equipment will perform poorly. A mixture that is too low will have the opposite effect.
How to start a craftsman chainsaw – Step by Step Guide
Starting a chainsaw can be dangerous if done improperly. Make sure you are wearing protective clothing and eyewear before attempting to start your chainsaw.
How to start a craftsman electric chainsaw?
To start a craftsman electric chainsaw, you’ll need to locate the on/off switch. This is typically a red button located on the rear handle of the saw. After locating the switch, hold it down and pull the starter cord slowly until you feel resistance.
How to rebuild a craftsman chainsaw carburetor?
There are some very good tutorials online with step-by-step guides on how to rebuild the carburetor. There are also replacement carburetors that can be purchased for less than $20.00 and they will come pre-assembled with all of the parts needed so you won’t have to rebuild it yourself.
Our Verdict
A Craftsman chainsaw is a very versatile tool and can be used to cut down thick tree stumps or saplings as well as delicate fruit branches. Chainsaws are one of the most dangerous tools that you will find yourself using, so being able to start them up safely and efficiently is imperative.
