how do you reset a maytag bravos washer

by Brenden Wyman Published 3 years ago Updated 2 years ago

Quick Method To Reset Maytag Washer

First things first, turn off your Maytag washer.
Disconnect the washer from the electric supply.
Wait for some time before turning on the machine again. ...
Now, plug in the socket and press the start button.
To reset the motor settings, lift the top lid up and down six times to reset the motor settings to default.

Full Answer

See more

How do I reset my Maytag Bravo top load washer?

The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.

How do I hard reset my Maytag washer?

Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.

Does a Maytag Bravos washer have a reset button?

How to reset Maytag Bravos washer- step by step. Turn the Cycle Selector knob counterclockwise or left (all the way around) once. Next, turn the knob clockwise (right) – Go three clicks clockwise (count one…

Does Maytag Bravos XL have a reset button?

Maytag Bravos XL washer calibration/ “Reset” (step by step) Turn the washer's Cycle Selector knob counter-clockwise or left once (all-the-way around). Now rotate the knob clockwise(right) – you should go 3 clicks clockwise(count 1… 2… 3 as you rotate the dial clockwise).

How do you run diagnostics on a Maytag Bravos washer?

0:060:55Whirlpool and Maytag washer diagnostic mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight right right left right this will bring this washer a diagnostic mode say you have a whirlpoolMoreRight right right left right this will bring this washer a diagnostic mode say you have a whirlpool Bravos. Machine it's the same basic procedure. But we're gonna start by hitting the power. Button.

How do I reset my washing machine?

1:173:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.

Why is my Maytag Bravos washer not spinning?

One of the most common reasons a washing machine won't spin is an unbalanced wash load. During a wash cycle, larger, heavier items can clump on one side of the machine, causing an imbalance that affects the spin cycle. Overloading the washtub with too many items can also cause an imbalance that prohibits spinning.

What do you do when your Maytag washer won't start?

This is how to properly reset a Maytag washer:Step 1: Unplug the machine.Step 2: Press and hold the POWER/START button for 5 seconds.Step 3: Hold down the PLAY/PAUSE button for 5 seconds.Step 4: Plug the machine back in and press POWER to restart.

How do you calibrate a Maytag top load washer?

0:050:58How to Calibrate a Top-Load Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the control dial one complete rotation 360 degrees counterclockwise. Quickly within about 6MoreTurn the control dial one complete rotation 360 degrees counterclockwise. Quickly within about 6 seconds turn the control dial 3 clicks clockwise.

How do you fix the LF code on a Maytag Bravos XL washer?

LF in the display Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve. This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.

How do you manually drain a Maytag Bravos washer?

Turn off the Bravos' water supply at the wall. Use pliers to turn the water supply hose connections at the back of washer counterclockwise to remove them from the appliance. Use a bucket to catch any water left in the hoses. Pull the drain hose from the appliance drain hose or utility sink.

Where is the reminder reset button on Maytag washer?

1-2 of 2 Answers Press and hold the "Spin" and "Soil" button simultaneously for 10 seconds. A countdown will be displayed on the console. Once the countdown has completed the unit will have successfully reset.

How do you fix a Maytag washer that won't start?

Why is my Maytag washer stuck on sensing?

These washers sometimes develop programming problems – an algorithm could have failed- so try to reset the washer and see what happens. The easiest way to reset it is by unplugging it for about 5 minutes then plugging it back in (you can also reset it via the breaker).

How do I reset the control panel on my Maytag dishwasher?

How to reset a dishwasher control panelFirst press the “Cancel/Resume” button, which won't be illuminated, then unplug the appliance from the outlet. ... Wait approximately 1 minute, plug the cord back into the AC outlet or flip the breaker back on.Start a new cycle and check if the dishwasher is working properly.

How do I put my Maytag front load washer in diagnostic mode?

0:000:36Maytag washer self-test mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd one of these buttons here and press them this way. One two three one two three one two threeMoreAnd one of these buttons here and press them this way. One two three one two three one two three then press the center button. And it's flashing now it's ready to go press Start.

How to reset Maytag washer?

Another simple way you can reset a top load Maytag washer is by first unplugging the washer for about a minute. Then after plugging it back you have a 30-second time frame to lift up the top lid of the washer and then bring it back to close. You have to do this six times within a twelve second period.

How to reset a washing machine code?

First, you need to unlock the lockbox, this will get your machine into program mode. After this, you have to move to the washing options and press the button that is for Delicates and Knits making sure that you hold it for a few seconds. If you have done this correctly then the LED display on the screen will flash and start to blink this means that all the codes of the machine have been completely reset. And so you can close the lockbox and bring the screen back to its standard display by pressing any button.

Why does my Maytag washer keep saying "Error code"?

The reason these error codes occur is because of various problems that the machine is facing like, a power spike or an unbalanced load, etc. And so there are multiple ways for you to reset a Maytag washer to remove these error codes.

Why does my washing machine give me an error?

And although this advancement is greatly beneficial, it has also opened a lot more opportunities for the machine to malfunction. This is because of a much complex operating system and intricate programming. And so once in a while, your washing machines will give you an error due to a small problem triggering the entire system. Which then requires a reset of the machine and all the commands that have been input into it.

How to make a dial clockwise?

To do that you have to first make sure that the main dial is at its standard ‘normal’ position. Then turn the dial counterclockwise making one full rotation and coming back to the ‘normal’ position. After that, turn the dial clockwise for only three settings so that the dial is now at the 3 o’clock position.

Does Maytag come with a warranty?

Although Maytag does come with a 10-year warranty, it is just limited to parts and does not include maintenance or replacement of the appliances themselves. Therefore it is a good idea to learn the basics about fixing these appliances yourself so that for minor inconveniences you are equipped to handle the situation.

Is Maytag a good company?

Maytag is one of the best companies in the USA when it comes to durable and reliable yet affordable appliances. But sometimes one of its machines might run into a small hitch that can leave you extremely frustrated even though it is not serious enough for a professional to examine it.

1. Quick Method to reset the waster

Mostly, a simple on/off can fix the machine. Follow the step guide below to reset your device using the on/off method.

2. Dial Rotating Method

Washers usually have a control panel that may include a dial. The washer can be reset or placed into different modes by turning the dial in a particular set of sequences.

3. The lid lift method

If you own a top-loading Maytag washer, the following method will help you reset your washer.

Knowledge Builders