How To Test Ice Maker Control Module
- Preparation. Check if there are any warnings of abnormal noises or smoke coming from your freezer. ...
- Turn off electricity. Before doing anything else, make sure that you are turning off the electricity to your ice maker. ...
- Remove Lock Nut and Connector. ...
- Unplug the connector. ...
- Remove screws holding the panel. ...
- Remove old ice maker control module. ...
Full Answer
How do I test my Whirlpool icemaker?
Ice maker module test for Whirlpool icemaker: Ice maker must be plugged in to the refrigerator. Shut-off arm down and the freezer is cold ( below 15 F ). Test points L & N will verify 120 volts to Ice Maker module. (Make sure your test probes go into the test points 1/2".) Test points T & H will verify if the bimetal thermostat is open or closed.
How do I change the thermostat on the module style icemaker?
Changing a thermostat on the module style icemaker.... Unplug the the fridge. Remove ice maker, remove 3 screws and unplug the power cord. Remove cover and shut off arm. Loosen the 2 screws holding housing support and module to mold and pull apart.
What are the holes in a modular ice maker for?
A modular unit will have several holes in the module, each marked with a letter (similar to the one pictured below). These holes are for test probes. If there are no holes then the ice maker is a component model and the components can be tested individually.
How do I test the control module of my therefrigerator?
Before testing the control module, unplug therefrigerator to avoid an electrical shock hazard. A modular unit will have several holes in the module, each marked with a letter (similar to the one pictured below). These holes are for test probes.
How to test ice maker control module?
Why unplug therefrigerator before testing?
How do you test an icemaker module?
1:252:33Troubleshooting a No-Ice Complaint and Testing-Replacing a Whirlpool ...YouTubeStart of suggested clipEnd of suggested clipBasically leave it until you hear a click and then go ahead and pull it out and you let it run tillMoreBasically leave it until you hear a click and then go ahead and pull it out and you let it run till right at the end of the cycle.
How do I test my ice maker solenoid?
1:142:46Refrigerator Not Making Ice? Inlet Valve Test, TroubleshootingYouTubeStart of suggested clipEnd of suggested clipUse a probe to touch one terminal of the coil you're testing and the second probe to touch the otherMoreUse a probe to touch one terminal of the coil you're testing and the second probe to touch the other terminal if the meter reading shows a result between 500. And 1500 ohms of resistance.
What does ice maker module do?
Ice Maker Components The control module, which contains a small motor, that drives a gear with a conductive pattern on the back, energizing various components at the proper time as it rotates. The harvesting arm removes formed ice cubes.
What tells the ice maker to fill with water?
Once the ice maker has been connected to a power and water source (aka the plumbing line connected to the back of your refrigerator), the ice maker cycle should begin automatically. At the beginning of the cycle, an electrical signal is sent to a water valve to fill the ice mold with water.
How do you test an ice maker with a multimeter?
0:092:49Testing ice maker voltage - How to measure voltage - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe black line always goes in calm it says column right down there I don't know if you can read thatMoreThe black line always goes in calm it says column right down there I don't know if you can read that and then your red line goes all the way over here. I'm setting mine on voltage.
How do you test the water inlet valve on an ice maker?
1:522:53Refrigerator Not Making Ice? Inlet Valve Testing - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow turn the water supply back on and observe whether or not there is a strong flow of water jettingMoreNow turn the water supply back on and observe whether or not there is a strong flow of water jetting out of the line a weak flow indicates a problem with the water line or the water supply valve.
How do you replace an ice maker module?
0:142:15Whirlpool Barracuda Refrigerator Ice Maker Module Replacement 8201515YouTubeStart of suggested clipEnd of suggested clipUsing a Phillips head screwdriver unthread the three mounting screws securing the module. You canMoreUsing a Phillips head screwdriver unthread the three mounting screws securing the module. You can now pull the old module. Out install the new icemaker module by positioning it in the housing.
Why does my water dispenser work but not my ice maker?
The water inlet valve is an electrically-controlled valve that opens to supply water to the dispenser and ice maker. If the water inlet valve is defective, or if it has insufficient pressure, it won't allow water to flow through. As a result, the ice maker won't make ice.
How do you jumpstart an ice maker?
3:484:44IceMaker Not Working - YouTubeYouTubeStart of suggested clipEnd of suggested clipAfter you jumpstart the water you want to make sure that this cycles through so you'll just startMoreAfter you jumpstart the water you want to make sure that this cycles through so you'll just start the icemaker. Itself. This is start to turn once you see attorney.
Why isn't my ice maker filling up with water?
Water may not be reaching the ice maker due to a frozen line, missing filter, or a closed supply valve. Repairing an ice maker that isn't receiving water is a process of elimination.
How do you troubleshoot an ice maker?
4:195:02Ice Maker Not Working? - Check these 6 Things first! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the water line you want to make sure it's not kinked it's not clogged. So how to do that is youMoreAnd the water line you want to make sure it's not kinked it's not clogged. So how to do that is you pull the fridge out make sure it's unplugged. Turn the water.
Where is the water sensor in ice maker?
The ice level sensor is located on the right side wall of the ice storage bin and monitors the ice levels. If the sensor is blocked or dirty it could cause the ice maker to stop ice production. Check the following: Make sure that the bin sensor is not blocked by the ice scoop or any other items that may be in the bin.
What does a solenoid do in an ice maker?
The electrical component that activates a valve to allow water to flow into the ice making area is called the solenoid. Coils that form the solenoid can become damaged over time, causing the icemaker to act erratically or produce no ice at all.
What does a solenoid do in ice dispenser?
The water flowing to the dispensers is controlled by a solenoid, meaning the solenoid transmits a message to the refrigerator's water inlet valve, telling the part when it's time to open. Over time, the coils in a solenoid can become worn or damaged, which can cause the part to malfunction.
How do you replace a ice maker solenoid?
1:113:46Whirlpool Refrigerator Ice Dispenser Solenoid #W10309866 - YouTubeYouTubeStart of suggested clipEnd of suggested clipDisconnect the wire connector. And use a quarter inch socket or nut driver to remove the screwsMoreDisconnect the wire connector. And use a quarter inch socket or nut driver to remove the screws securing the grounding wire. Pull the retaining tab back and remove the old solenoid from the housing.
Why is my ice maker not getting power?
A clog, leak, or damage in the water line may cause the ice maker to shut off automatically or otherwise stop working. Check the ice maker inlet valve and water supply tubing for any leaks, damage, or blockages.
How to align ejector with gear on module?
Align ejector with gear on module, at about the 1:30 position. Push the mold and housing support together. Tighten the screws to make good contact with mold.
Why are my ice cubes black?
If you see black bits in your ice cubes, the finish probably is coming off the body of the ice maker. You can replace the body as a separate part but often a new ice maker can be close enough in cost. So a whole new ice maker kit should be considered.
What to do if your motor doesn't run?
If the motor doesn't run, replace the module assembly. If you leave the jumper in for a half of a revolution, you can feel the heater in the mold heat up, if it is good. Remove the jumper and the water valve will be energized in the last half of the revolution.
Check the warranty
Checking the warranty of the refrigerator is very important as it will help you to know about its durability. The refrigerator’s warranty will give you complete peace of mind as it is one of the most important factors that are considered while buying a refrigerator.
Check the power consumption
If you are planning to buy a small refrigerator then don’t forget to check the power consumption. You don’t need to worry about the power consumption of a big fridge, but for a small one, make sure that you don’t consume more than 4 kWh per day.
Make sure that there is enough space inside the refrigerator
After checking all the above-mentioned points, now you should go through the inside of the refrigerator. You need to make sure that the space inside is not too less or too much.
Check the noise
The last thing that you should consider while buying a refrigerator is its noise. A small refrigerator shouldn’t make any noise and you shouldn’t get any disturbance while using it. But if the noise level is too high then it is better to avoid it as it will affect your work and sleep.
Conclusion
In conclusion, these are some basic tips which will help you to find the best model of refrigerator for you. I have also shared with you some points regarding the power consumption and noise level. So, before purchasing a refrigerator always remember to check them properly.
How to test ice maker control module?
Testing should be done with the power off, the shutoff arm in the down, "on" position and the ejector blades in the "start" position. The position of the blades will vary among ice makers, but the start position is always with the blades over (not in) the ice mold tray. If the ejector blades are in the mold, it will not be possible to properly test the control module. Furthermore, if the blades are in the mold area, then they did not complete their cycle, and may suggest a failure of the modular unit.
Why unplug therefrigerator before testing?
Before testing the control module, unplug therefrigerator to avoid an electrical shock hazard.
