Build a Fence Using Post Spikes
- Get Ready. Determine where your property line is (you may want to get your lot surveyed) and check with your local municipality to see if you need ...
- Install the Posts. Start at a corner and drive the first spike into the ground at the marked location. ...
- Install the Fence Rails. ...
- Attach Fence Boards. ...
How do you install a metal spike on a fence?
Once the spike is in the ground and the metal box is the only thing visible, install the wooden post. Then, move to the next corner post and install the spike and wooden post there, again ensuring it's straight.
Are spikes on a fence stable?
A fence that uses fence post anchor spikes is just as stable as a fence with posts set in concrete, with the added benefit of minimizing the rotting of the fence posts.
How to set a fence post anchor spikes?
Use a sledge hammer and a block of wood to drive the post anchor into the ground. Don’t hit the metal directly with the hammer because you could damage it. Once the anchor is driven all the way into the ground, slide the 4×4 post into the sleeve. Then tighten the sleeve bolts. Fence post anchor spikes are a great way to quickly set a fence post.
How do you keep a fence post from falling down?
There is a bolt on the side of the holder that can be done up easily with a spanner to keep the post firm in the spike. As you tighten the bolt check with a spirt level that the post is upright – not leaning backwards or forwards, or to the right or left. Using Metal Spike Post Holders – tightening the bolts to the fence post
Do fence post spikes work?
Fence post anchor spikes work well by allowing one to place and remove fence posts without having to dig large holes. A fence that uses fence post anchor spikes is just as stable as a fence with posts set in concrete, with the added benefit of minimizing the rotting of the fence posts.
How do you install ground spikes?
0:001:18How to install a Ground Spike - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first thing to do is to dig a hole. The same depth as your ground spike and about a spades widthMoreThe first thing to do is to dig a hole. The same depth as your ground spike and about a spades width wide. Put the ground spike in the hole. And then add the post mix concrete.
Are fence post spikes better than concrete?
The main advantage of metal fence spikes for post support is their ease of installation, using only simple tools with no need for digging or concrete. Even high-quality treated timber posts will decay to some degree over time when sitting in concrete.
How do you secure a fence post without digging?
Instead of digging a hole for the post, use a metal spike anchor( this is Amazon Link) to mark the location of the hole for your fence post. Then, using a sledgehammer, pound the metal spike into the earth until a suitable hole for your fence post is formed.
How do you install fence repair spikes?
0:111:23How to replace a damaged or rotten fence post - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake a fence fast repair spur. And position it over the corner of the old post. Using a dolly andMoreTake a fence fast repair spur. And position it over the corner of the old post. Using a dolly and sledgehammer carefully drive the repair spur. Between the old wood of the post. And the concrete.
How do you secure a fence post in the ground?
0:511:59How to install a fence post into soil - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can cover the top of the cement with soil pour water over the cement screw a couple of battensMoreYou can cover the top of the cement with soil pour water over the cement screw a couple of battens to the posts. To make sure that they remain securely upright all the time checking the levels.
How do you put 4x4 in ground without concrete?
How To Set Posts Without Concrete: Step By StepDetermine where you want your post to go. ... Once the hole is dug, dump four inches of gravel into the hole. ... Once you have placed the post, add another two inches on top of the four inches of gravel that you have already placed. ... Next add a few inches of topsoil.
How do you secure a 4x4 post in the ground?
5:2710:573 Tricks To Installing Stronger 4X4 Wood Fence Posts That Last LongerYouTubeStart of suggested clipEnd of suggested clipSo one way you can prevent that is by putting a three to six inch layer of gravel. Down underneathMoreSo one way you can prevent that is by putting a three to six inch layer of gravel. Down underneath each post. So in my case my holes have to be dug 36 inches deep at a minimum to set my post.
How do you install wall spikes?
We install wall spikes by drilling a 5mm or 6mm hole and hammering a 5mm or 6mm nail-in anchor through the base of the spike and into the wall. This ensures a steady, reliable fixture. We provide a range of around 10 different styles of spikes to suit your preference and specific needs.
How do you install EZ Spike?
0:286:30How to install a METPOST/Fence Spike like a pro! - YouTubeYouTubeStart of suggested clipEnd of suggested clipMeans that as I'm hitting it twists slightly towards me so what I do is do a 8 4 turn anti-clockwiseMoreMeans that as I'm hitting it twists slightly towards me so what I do is do a 8 4 turn anti-clockwise. And if you're right-handed to 1/8 of turn clockwise.
How do you set a fence post by yourself?
1:494:44How to Set a Fence Post. FAST! - YouTubeYouTubeStart of suggested clipEnd of suggested clipUntil you get nice and plump. And you get it plumb by maneuvering those braces backwards. AndMoreUntil you get nice and plump. And you get it plumb by maneuvering those braces backwards. And forwards once you get this post nice and straight this type of concrete.
How do you stabilize a freestanding fence?
1:128:21How to Fix a Leaning Fence - YouTubeYouTubeStart of suggested clipEnd of suggested clipBecause we had limited room we had to use a rope also make sure you have a shovel a month pickMoreBecause we had limited room we had to use a rope also make sure you have a shovel a month pick hammer and drill. So these tools to dig out to attach to hammer in the product.
Is 2 feet deep enough for fence posts?
The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).
How do you remove a ground spike?
2:022:59How To Remove A Steel Fence Post Or Ground Spike Out Of The GroundYouTubeStart of suggested clipEnd of suggested clipJust take a little bit into the ground first and get it underneath this collar right here. Because.MoreJust take a little bit into the ground first and get it underneath this collar right here. Because. If you try and pull it right straight up it won't come you have to actually bend.
How long is a standard spike?
We offer a standard 75mm x 75mm square which will fit most fence spikes, and our fence post spikes are 750mm in length which is essential for fence post above 4ft. Each spike is fully galvanised and has drainage holes to ensure the quality of your fence post stays for as long as possible.
Do fence post spikes last?
Well, here is a guide to help show how fence post spikes are a crucial addition to the process. Fence post spikes ensure the fence last for as long as possible and will withstands the elements.
How long is a post spike?
A post spike is a heavy metal spike about 24 or 30 inches long with a metal box (usually 4x4) attached to the top, designed to hold the base of a wooden fence post. You simply drive the post spike into the ground where you want to put your fence post and then insert the wooden post into the box. The idea is to provide a convenient and economical way to build a fence—no need to dig holes and pour concrete, and the post spikes only cost a few dollars each.
Why do fence posts get twisted?
Second, over time fence posts set in the ground can get twisted out of plumb, usually as a result of frost or moisture causing the ground to shift. Post spikes are available with the 4x4 box actually attached to the base on an adjustable swivel. This allows you to install the post perfectly plumb (even if the spike itself isn't driven straight into the ground), and if the post moves over time, you can adjust the swivel and plumb it back up.
How far down should a 24" spike go?
In general, the 24" spikes should only be used for fences up to 48", while the 30" spikes can only support fences up to 60". Finally, remember the post only goes down as far and the base of the box, so you could be left with a gap on the bottom of the fence.
What is the purpose of a fence?
Fences serve all kinds of purposes. Some are practical—barbed wire or a corral fence, for example—while some are decorative—like that white picket fence around the cottage. Some are designed for a particular purpose, such as the five foot wooden fence around a yard designed to provide privacy. No matter what the purpose of a fence is, they all have fence posts.
What is the hardest thing to do when building a fence?
In many instances, the hardest thing about building a fence is digging the holes and setting the posts. However, there is another option. Post spikes can provide a base for fence posts and eliminate all that digging and concrete pouring prior to building your fence.
Can you build a fence with post spikes?
Building a fence using post spikes does eliminate a couple of the things that can make fences go bad.
Can you use fence spikes on chain link fences?
Fence spikes aren't applicable for all types of fences. They're designed to work with 4x4 wooden posts, so obviously they aren't any good for chain link or other industrial type fences. Also, because they really aren't as structurally sound as a wooden post set directly into concrete, the height of the fence you can build using these spikes is limited.
How do fence post anchor spikes work?
Fence post anchor spikes work well by allowing one to place and remove fence posts without having to dig large holes. A fence that uses fence post anchor spikes is just as stable as a fence with posts set in concrete, with the added benefit of minimizing the rotting of the fence posts.
How long do fence post spikes last?
Due to their steel construction, the fence post anchor spikes will last for years and years (some even lasting for up to 50 years!).
What is a Fence Post Anchor?
A fence post anchor is a spike normally made of galvanized (and sometimes powder-coated) steel. This spike has a box at the top of it to fit your fence post into. The box enables you to easily place the fence post into the anchor, once the anchor has been properly set and leveled in the ground.
What is the hardest part of setting fence posts?
Fortunately, the hardest part of setting fence posts when you use fence post anchor spikes is the setting of the anchor spikes themselves. Even still, it’s a fairly simple task.
What is the benefit of using a fence post anchor spike?
One of the biggest benefits of using a fence post anchor spike is ease and simplicity of setting and removing fence posts.
Is a fence post stable?
Additionally, fence post anchor spikes are very stable. Fences with posts set in anchor spikes are just as stable as fences with posts set in concrete.
Where do you put anchors when replacing a fence?
If you are replacing a pre-existing fence, put the anchors right where they were. If you are putting in a fence that wasn’t there before, be explicitly sure that you are on your own property.
What Size Fence Spike do I Need?
This obviously depends on the size of your post and the height of your fence, or other structure.
How to hit a fence spike with a mallet?
You push the fence spike into the ground as far as you can by hand, then slot the driving block into the top of the fence spike and hit the top of the block with the hammer or mallet.
Why do fence posts fail?
Most fences fail when the fence posts break due to rot or insect damage. If you have a broken fence post due to storm damage or rot, but most of the fencing is still intact you might want to just repair the post using a repair spike like the ones below. Fence post repair spike.
What happens when you tighten a rawl bolt?
With the rawl bolt, as the head of the bolt is tightened the bottom sheath expands, gripping the concrete.
How to make a driving block?
You could make your own driving block by cutting a short length of fence post and using that as a block.
What is a concrete fence post holder?
Concrete-in fence post holders are designed for use where soil conditions are unsuitable for drive-in spikes.
How to mark holes in post holder?
Place your post holder in position and mark through the holes onto the surface below using a permanent marker or similar .
What is a fence post mix?
A fence post-mix is a serious fixing and will generally outlast the fence post. You dig a deep hole about 2 feet, making sure the lower half is rounded (football size) for a sturdier fixing. A Post mix is made of shingles, cement and sand. You can purchase a single bag of post-mix that will be enough for ONE fence post.
Which is better: post mix or spike?
A post-mix is stronger and lasts many more years when compared to a spike. If you are erecting a fence for a short period then the fence spike will be the better option because it’s easy to remove.
What happens when you add wind and rain to a fence?
Once you add wind and rain the spike will become loose and your fence panel will start to move.
Can you use spikes for a fence?
Fence spikes really are a very temporary solution and should never be used for a long-standing fence. Easily hammered into clay or soil. Will only last a year before they move. Good for temporary fencing. More expensive than using a post-mix.
