How to Use the Fuel Line Disconnect Tool
- Step 1 Empty the Fuel Lines. With the car parked safely, start the engine and leave it to idle. This will help use up...
- Step 2 Wait for the Engine to Stall. After removing the fuse, the engine will take no time to stall. Wait for it to stop...
- Step 3 Wear your Protective Gear. Meanwhile, put on your safety gear. Doing that will...
How do you disconnect quick connect fuel lines?
Quick Disconnect fitting 14213Q fits 40 hp and larger Force outboards (1993 and newer), 9.9 through 25 hp Force outboards (1998 models) and all Mercury and Mariner outboards using the clip on type quick disconnect fitting at the engine end. The fuel line barb fitting is for 1/4" ID fuel line hose.
What tool is needed to remove fuel line?
lisle is the fuel line disconnect tool you need. Spray it with wd 40 or pb blaster I figured it out. I got the tool from Merchant Automotive since it had both sizes I needed. I really didn't understand the idea of what needed to be done until I was able to get the first one out.
How do you remove a fuel line?
To install:
- Insert a new retainer into the connector.
- Apply a light coating of fresh engine oil to the fuel pipe.
- Carefully press the fuel pipe into the connector making sure the retainer snaps in place completely.
- Inspect for leakage and repair as necessary.
How do you disconnect a quick connect gas line?
Situation 2: Connections to Soft Copper
- Match flare fittings to the outside diameter of the soft copper you're connecting to. ...
- Cut a new length of coiled soft copper, flare the ends and connect it with flare fitting.
- Or replace the damaged tubing with a flexible stainless connector as shown here.
How do you use a fuel and transmission line disconnect tool?
1:426:35Harbor Freight Laguna Fuel/Oil/Air Line Disconnect Tools ReviewYouTubeStart of suggested clipEnd of suggested clipHard line so you'll work this tool in until you can feel it. Get the little times released. And thenMoreHard line so you'll work this tool in until you can feel it. Get the little times released. And then you'll pull off the line simultaneously pushing on the tool to get it to release.
How do you use the AC fuel line disconnect tool set?
0:070:53OEMTOOLS 27318 Master Disconnect Set - YouTubeYouTubeStart of suggested clipEnd of suggested clipSelect the disconnect tool that fits the fuel line diameter. Attach it to the line and snap it intoMoreSelect the disconnect tool that fits the fuel line diameter. Attach it to the line and snap it into place.
How do you use a hose disconnect tool?
0:441:53FUEL LINE DISCONNECT TOOL. A/C DISCONNECT TOOL - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext pull the pipe in push. The tool all the way in you can see just like that all the way in after.MoreNext pull the pipe in push. The tool all the way in you can see just like that all the way in after. That you just grab the tool. And slowly pull it out.
How do you use a fuel line connector?
0:513:37Install Fuel Line Connectors with the EZ-ON Hose Press - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor straight fittings all you need to do is clamp the appropriate size pin into the tools vise andMoreFor straight fittings all you need to do is clamp the appropriate size pin into the tools vise and place the fitting over the pin.
How do I disconnect quick connect fuel lines without tool?
4:368:00How To Remove Ford Fuel Line Fittings Without Fancy Tools! Quick ...YouTubeStart of suggested clipEnd of suggested clipSo I'll push the fuel line this way push the clip that way. And it should come off. Make sure youMoreSo I'll push the fuel line this way push the clip that way. And it should come off. Make sure you release the fuel. Pressure before attempting. This.
How do you remove an air conditioner without a tool?
0:503:50How To Disconnect AC Lines With Or Without The Spring Lock ToolsYouTubeStart of suggested clipEnd of suggested clipI think it was to a teflon tape roll. And I just cut it with a razor blade. And I'll show you how itMoreI think it was to a teflon tape roll. And I just cut it with a razor blade. And I'll show you how it works just take it you stick it in there.