How to Apply Sikkens Cetol
- Smooth the surface to be treated with sandpaper. Use it to remove any splinters, raised grain or dirt.
- Use your natural bristle brush to work on a warm day with humidity less than 80 percent. Apply a primary coat of Cetol 1.
- Clean your brush in mineral spirits. ...
Can I apply Sikkens cetol in the Sun?
Avoid applying in direct sunlight, if possible. Do not thin Sikkens Cetol, even on the first coat. Using a long-haired natural bristle-type brush, apply a liberal coat. Allow 24 hours to cure before applying the next coat. Do not sand between coats, as this product needs the full application thickness from each coat for its UV effectiveness.
What is the difference between Sikkens cetol and maintenance coats?
With maintenance coats, pigmented products will further darken the wood. With a one coat application of Sikkens Cetol Maintenance, the wood will retain the same look and color.
How do you use cetol 23 plus?
Apply a primary coat of Cetol 1. Saturate all exposed grain ends and knot holes. Clean your brush in mineral spirits. Allow the product to dry for a minimum of 24 hours. Spend another warm day with less than 80 percent humidity, to apply an initial coat of Cetol 23 Plus.
Why choose Sikkens cetol filter 7 Plus?
Its highly translucent, semi-gloss finish will help to highlight the grain and colour of the timber, while working hard to give outstanding protection against the damaging effects of the UV radiation sunlight. But perhaps even more importantly in our climate, Sikkens Cetol Filter 7 plus is also microporous and water repellent!
How do you apply Sikkens?
0:472:53Sikkens - How to Prepare and coat time windows and doors - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe product is brushed evenly onto the timber surface. Take care to attend to any runs. Allow 24MoreThe product is brushed evenly onto the timber surface. Take care to attend to any runs. Allow 24 hours to properly dry.
Do I need to sand between coats of Sikkens?
Sikkens Cetol Deck Slip Resistant Do not sand between coats. Always apply coatings along the grain and never across.
Which Sikkens product to use first?
On new work and when any bare timber is exposed, a base stain of Cetol HLS plus should always be applied first. It is important to satisfy the absorption of the timber; the best way to do this is to apply the HLS plus quite liberally and then redistribute any excess after about 5 minutes with a virtually dry brush. 3.
How long does Sikkens cetol take to dry?
Sikkens Proluxe Cetol SRD Dry Time Drying Time – 24 hours minimum at 68°F and 65% relative humidity. At temperatures below 50º F (10º C) or conditions of high humidity the drying time will be extended. Proluxe Cetol SRD dries to touch in approximately 6 hours. Wait 24 - 48 hours for light foot traffic.
How long does sikkens cetol last?
Sikkens states in their literature that you should expect to get 2-4 years life out of their system on a sunny side of a house, and 3-5 years on a shady side.
How many coats of cetol are there?
three coatsCetol 1 is always used as the first coat in any bare wood application. All systems consist of three coats. All three coats must be applied within 30 days after preparation.
Is Sikkens a paint or a stain?
A high quality, solvent-based wood stain for interior and exterior joinery.
Can you apply Sikkens over stain?
Not all stains are compatible with marine wood finish systems such as Sikkens Cetol Marine. It is recommended that Cetol Marine be applied directly to bare wood, or to a previously applied Cetol Marine finish that's in good condition, and not to stain or wood finishes other than Cetol Marine.
What is the difference between cetol 1 and cetol 23?
Cetol 1 is a premium, translucent exterior wood basecoat to be used with Cetol 23 Plus. Its superior oil alkyd formulation offers excellent penetration and adhesion to vertical wood surfaces. Cetol 23 Plus is a premium, translucent topcoat for Cetol 1.
Is sikkens oil or water based?
water basedSikkens Cetol BLX-Pro is a quick drying water based exterior timber finish that is ideal for decks and outdoor furniture providing good durability and flexibility.
Can sikkens be applied with a roller?
not recommend the use of. applicator pads or paint rollers as. they tend to spread the product too.
How do you prepare for cetol?
preparation by applying a solution of four ounces of oxalic acid crystals in a gallon of warm water. This solution should be allowed to sit on the affected areas for 15-20 minutes before the final rinse with clean water. Let dry 48 hours before coating.
Can you recoat cetol?
Note: Once you apply Sikkens ProLuxe Cetol Maintenance RE removal of all product is necessary to recoat with Cetol Log and Siding or Cetol 1, 23 Plus. Sikkens Cetol Maintenance RE wood finish should be applied within four weeks of surface cleaning, provided that the surface remains free of dirt, grease, grime, mildew.
Can you apply Sikkens over stain?
Not all stains are compatible with marine wood finish systems such as Sikkens Cetol Marine. It is recommended that Cetol Marine be applied directly to bare wood, or to a previously applied Cetol Marine finish that's in good condition, and not to stain or wood finishes other than Cetol Marine.
Can Sikkens be painted over?
To paint over the Sikkens HLS oil stain on your handrail is a fairly simple process... lightly sand timber with 80-120 paper to remove any obvious loose material,apply a coat of turps based primer/undercoat,allow to dry for 24 hours or so then apply your exterior acrylic coating...
How do you use Sikkens ProLuxe?
Apply liberally to entire area, working the solution into and around the fastener inset areas where iron stains exist. Work into the wood-grain with a stiff bristle brush in a scrubbing motion to accelerate the brightening and cleaning process. Allow the oxalic acid solution to sit on the surface 15-20 minutes.