What does E2 and F5 mean on a whirlpool washer?
The error message E2 and F5 indicate that the door is not locking properly. The door must be completely closed for the washer to operate. The door may look as if it's closed, but it may not be latched. Open the door and firmly close it. Before you close the washer door, check for laundry items sticking out beyond the door opening.
What does F05 mean on a washing machine?
F05 means there is a problem with the pump or there is a waste pipe issue. This problem will mean that your washing machine door may not release, leaving your washing trapped inside, or if it is opening, your washing will be sat in a pool of undrained water.
What does F13 mean on a Hotpoint washing machine?
F13 – A fault with the dryer temperature sensor (only on washer-dryers) For more information about each of these fault codes on Hotpoint washing machines, check out their service page with each error code (there are more than just the F-codes listed above) and a more in-depth description of the faults.
What does error code F05 mean on Kenmore dryer?
F05 – A problem with the pump or blockage in the waste pipe F07 – A fault with the electronic/heating circuit board F13 – A fault with the dryer temperature sensor (only on washer-dryers)
How do I get rid of E2 error on my washing machine?
An E2 Error code indicates that the washer is still draining after 8 minutes. Check the following: Check that the drain hose is not more than 391 ⁄3" (100 cm) from the floor. Remove any clogs from the drain hose.
What does F5 mean on a washer?
What could that mean? The Maytag washer code F5 is an alert that tells you the lid can't lock. There could be some clothing or other obstruction in the lid preventing it from locking. This is one of the simplest problems to fix.
Why is my Whirlpool washer saying E2 F5?
This error code indicates that the door is not locking properly.
What does f3 E2 mean washing machine?
Temperature Control issue The F3E2 Error Code indicates that there may be an issue with the Temperature Control sensor. Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
How do I fix error F5 E2?
Possible Solutions The F5 E2 alert indicates the washer can't engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.
What does the F5 error code?
An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions.
How do I fix E2 error on my Whirlpool washer?
Whirlpool error F05 or E2 This means there's something wrong with the water temperature sensor. Time to reset the Whirlpool. Switch off the washing machine and remove the connector for 30 minutes. Afterwards, plug the washing machine back in and start it up again.
How do I clear the error code on my Whirlpool front load washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do you reset a Whirlpool washing machine?
Follow these steps to reset your Whirlpool washer:Turn the washing machine off using the control panel.Unplug the washing machine.Wait three minutes.Plug the washer back in, and wait thirty seconds before turning the washer on.
What is F3 E2?
The F3E2 error code occurs when five consecutive loads are dried without registering moisture sensor data. Pressing the 'Power' button will clear the error code and allow you to restart the machine. If the problem persists, call for service.
What does F3 E2 mean on a Whirlpool Duet washer?
0:535:52DUET WASHER F3 - E2 ERROR - QUICK FIX - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the reason we're getting this error is a little wire has broken that sends a signal on theMoreAnd the reason we're getting this error is a little wire has broken that sends a signal on the temperature sensor the temperature sensor connects into the plastic tub through the back.
How do I fix the F3 error on my washing machine?
Step 1 – Reset Your Washer. The best place to start is to do a simple reset of your washer. ... Step 2 – Check the Switch Hose. ... Step 3 – Check the Water Level Sensor. ... Step 4 – Check the Air Trap Pipe. ... Step 5 – Check the Wiring. ... Step 6 – Replace the Control Board. ... 5 Reasons Why Your Refrigerator Is Making Noise.
How do I reset the F5 code on my Maytag washer?
F5 E4 or dr Error CodePower unit down by turning off the circuit breaker or unplugging for one (1) minute.Power unit up by reconnecting power.Open and close the door.Restart a new cycle.Monitor the washer for one (1) minute to ensure the error code does not display again.
How do I fix error F5 E3 Cabrio washer?
The F5 E3 alert indicates there is issue with the lid lock. Do not force the lid open, as permanent damage could occur. Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid.
What does F5 mean on Whirlpool?
A two-digit Whirlpool F5 code is a control board failure, according to Appliance Parts Pros, and the control board will need to be replaced. A four-digit F5 code will be of the format F5 EX, where X is a number between 0 and 7.
How do I fix e5 error on my Whirlpool washer?
This alert indicates the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.
What does F05 mean in washing machine?
F05 means there is a problem with the pump or there is a waste pipe issue. This problem will mean that your washing machine door may not release, leaving your washing trapped inside, or if it is opening, your washing will be sat in a pool of undrained water. Read our post here about what to do if your washing machine isn’t draining ...
What is F01 in electrical?
F01 – A fault with the electronic circuit board
What is the error code for Hotpoint washing machine?
Error codes on Hotpoint washing machines run from F01 to F18 and each code means something different – allowing you to know exactly what the problem is with your machine. Here’s a brief rundown of what each code means:
What is fault F13?
F13 – A fault with the dryer temperature sensor (only on washer-dryers)
When will washing machines be available in 2021?
January 9, 2021. January 9, 2021. / Washing Machines. Washing machines these days are all singing and all dancing, which can be extremely helpful, especially when you want to troubleshoot your machine to find out what’s causing any problems.
