What does it mean when your washer says PF?
a power failureThe PF Error Code indicates a power failure. This might occurswhile machine is working due to external disturbance. Try starting the machine again by pushing start/pause button.
What causes a Kenmore dryer not to start?
If a Kenmore dryer's start switch button is constantly engaged but the machine won't turn on, it may be an indication of either a defective power cord or a defective control panel. The most common reason for such problems is an overloaded outlet or circuit.
How do you reset the codes on a Kenmore Elite dryer?
Unplug the dryer for 5 minutes and then plug it in. If the code returns, then replace the main electronic control board. A button is stuck on the keypad on one of the two user interface control assemblies in the console. If you can't free the button, replace the user interface control assembly with the stuck button.
How do you fix the PF code on a dryer?
A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure. Touch and hold START to restart the dryer cycle or press POWER to clear the display.
When I press the start button on my dryer nothing happens?
Check the exhaust vent because a clog in the vent likely caused the thermal fuse to blow. For dryers with a dial timer, a broken push-to-start switch can prevent the motor from running. Use a multimeter to check for continuity through the push-to-start switch.
Why does my dryer have power but wont start?
This could be a tripped breaker, a blown fuse, or something as simple as unplugging the dryer from the wall. What is this? Check if the dryer is plugged in or at least plugged in securely to the outlet. Next, check your breaker box.
How do you reset a Kenmore dryer control board?
Many dryers are equipped with a reset button on the control panel. If the motor won't run, let the dryer cool for about ten minutes. Then push the reset button. If there are no problems with the motor, switches, or electrical system, this should restart the dryer.
What does F1 mean on a Kenmore Elite dryer?
The “F1” error means that the dryer's thermistor failed. The dryer is reading the thermistor as “open” and the actual part has shorted out. The thermistor is used to read and control temperatures within the dryer.
Why does my Kenmore Elite Dryer keep shutting off?
The high-limit thermostat monitors the dryer temperature and shuts off the burner if the dryer overheats. If the high-limit thermostat is malfunctioning, it may shut off the burner even if the dryer is not overheating.
How do you fix the PF on a Kenmore dryer?
PF is power failure error meaning electricity has been interrupted to the machine. An electrical interruption of any type can cause a PF error code. Try this: Press the Pause/Cancel/Stop button twice to clear the PF in the display.
Why is my dryer stuck on sensing?
So, if it gets stuck in Sensing mode, that means that something has gone wrong with that process, and it can't start the drying cycle. At first glance, you may be dealing with a problem with the moisture sensor. Just like with previous problems, be sure to check and clean the moisture sensor and see if it works then.
What does PF mean on a heater?
PF means Probe Failure.The unit requires service. You need to contact our hotline for assistance.(For US 1-800-322-3848; For Canada 1-888-335-6644) or look for the closest service center.Please check the service locator found in this website.
Why won't my dryer start all of a sudden?
The first issue to check for when a dryer won't start is whether the power cord is properly plugged in, directly connected, or showing signs of serious damage. Also, a dryer requires a lot of electricity to operate, so it may have tripped the breaker when pulling the necessary power.
Where is reset button on Kenmore dryer?
There is no reset button on your dryer. I recommend locating the two (2) house circuit breakers dedicated for the dryer and reset both circuit breakers by flipping them both OFF and ON 2-3 times and then check to see if the dryer will start. and then removing the rear panel.
How dO I know if my thermal fuse is blown?
To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
How do you check the start switch on a Kenmore Dryer?
1:141:56Dryer Won't Start? Two Terminal Switch Testing, Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou begin make sure the switch you're testing has been removed or isolated from the appliance use aMoreYou begin make sure the switch you're testing has been removed or isolated from the appliance use a probe to touch one of the switches terminals and the second probe to touch the other terminal.