Full Answer
What is the difference between a wall and a chase wall?
A properly installed chase wall is indistinguishable from an original wall. In contrast to a chase wall, a wall chase is a groove or larger indentation cut into a brick or concrete wall to hold pipes or wiring. Wall chases serve a similar purpose to chase walls and are often installed during remodeling projects.
What is a chase in construction?
A chase is drilled in a concrete floor construction or wall and helps accommodate features like cables and pipes. The width of chase often varies depending on the type or the number of services it will enclose.
How do you chase a cable up a wall?
Chasing cables and pipes into walls. When running cables or pipes up (or along) a masonry wall, the neatest method is to bury (or, in builders terms, chase) them in the wall surface. There are a few guidelines to be followed when chasing cables or pipes into walls:
Can you chase pipes or cables into walls?
You have to follow several guidelines when you are chasing pipes or cables into walls: You should avoid cutting a chase at an angle between the start and the finish of a wall. Instead, a chase cut-out should always be horizontal or vertical between the start and the wall’s finish.
What is a chase in a house?
What do professional builders use when cutting a chase in a wall?
How to hide cables?
Why do builders chase cables?
How to chase cables into walls?
Why should cables be chased vertically?
How deep should a horizontal chase be?
See more
What is Chase in brick wall?
When running cables or pipes up (or along) a masonry wall, the neatest method is to bury (or, in builders terms, chase) them in the wall surface.
What does chase the wall mean?
A chase is a groove or channel cut into an existing layer or substrate to accommodate services such as pipes or cables. Chasing is the act of cutting a chase and is usually undertaken in solid wall or solid floor construction.
What is chases in masonry?
Electrical chase is a technique used for cutting proper channels in masonry or concrete. Chasing is a continuous recess within the floor, ceiling and walls for the required pipe work and conduit.
What does Chase mean in construction terms?
A chase, as it pertains to new home construction, is a vertical space in a wall that provides an area for pipes or wires to run through. These chases are placed in a strategic way so that cables can be gathered and run together. A chase is simply installed from a single open space to another.
How do you chase a brick wall?
1:3518:05How to Chase a Wall and Fit a Flush Single or Twin Socket ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipPen. Both sides the reason i like the line to be thicker than rather than using a pencil using aMorePen. Both sides the reason i like the line to be thicker than rather than using a pencil using a thick pen in this case is that we tend to chamfer. In slightly when we chase.
How do you fix a chased wall?
2:4721:03How to Fill Wall Chases, Cracks & Holes - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you've got to think about the job you've got to do. And pick the right product for the job theMoreSo you've got to think about the job you've got to do. And pick the right product for the job the standard bonding code with its 45 to 90 minute working time and 120 minutes setting.
How deep should a chase wall be?
The document states that, vertical chases shouldn't be deeper than 1/3 leaf of the wall, and horizontal chases shouldn't be deeper than 1/6 of the leaf.
What is the difference between a chase wall and a shaft wall?
Registered User. Dictionary definition: (a continuous recess: Harris) a vertical or horizontal enclosure/recess (of rated or non-rated construction) with which to conceal/route, plumbing, electrical, etc.; shafts tend to be vertical while chases may be either.
Do electricians chase walls?
Electricians regularly chase walls but homeowners and other trades people can do the task for them. As the position of the wall chases are governed by wiring regulations, many electricians prefer to do the task themselves in order to ensure compliance.
What is an interior chase?
A chase in home construction is a vertical space in a wall, which provides an area for pipes or wires to run through. Builders strategically place chases to ensure that cables run together. A chase may run up the wall from the basement to the attic or the upper part of your home.
What is pipe chase?
A pipe chase is an enclosed, finished space used to house and conceal pipe runs.
How do you chase a pipe through a wall?
Always cut a chase vertical or horizontally, never diagonally. This reduces the chances of someone driving a nail into cables or pipes in the future. If making a vertical chase, the chase should not be deeper than a third of the wall's thickness.
What does Chase mean slang?
noun. a guy that will do anything to get any action from a girl but she won't give him the time of day. The chase went after the girl last night.
How do you chase a wall for TV cables?
0:0418:29How To Hide Cables/Wires In A Brick Wall - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet it back enough to him hide those cables in there and then what i'll do is re-plaster. And re-MoreGet it back enough to him hide those cables in there and then what i'll do is re-plaster. And re-sort of finish off the first surface of that with a fine fill.
How do you chase a pipe through a wall?
Always cut a chase vertical or horizontally, never diagonally. This reduces the chances of someone driving a nail into cables or pipes in the future. If making a vertical chase, the chase should not be deeper than a third of the wall's thickness.
How deep can you chase a wall?
The document states that, vertical chases shouldn't be deeper than 1/3 leaf of the wall, and horizontal chases shouldn't be deeper than 1/6 of the leaf.
How deep should wires be chased in to walls? - MyBuilder
All electrical cables should be set into the walls at a minimum depth of 50mm if they are not mechanically protected. If it isn't possible to chase the walls to that depth then the cables should be set deep enough so that metal capping can cover them and allow for plaster to cover that.
How To Chase Pipes Into A Wall | Hide Those Pipes | Checkatrade
How to hide exposed pipes. If you have exposed pipes that can’t be chased into a wall, take some tips from these alternative ways of disguising them:
Why should you put a chase on a wall?
Common sense really – If the chase is too deep it will impair the stability of the wall. If chases are back to back, there is no wall! It must always be remembered that the person doing the electrical work may not be the same person who wants to hang a picture on that wall or put a serving hatch or window in it. All chases therefore should be sensibly placed to give everyone a chance of working out where they are in relation to lights, switches, sockets and appliance points.
How long to leave chase on wall?
The chase is then left for 30 minutes or so, when we use a pointing trowel to cut the surface back about 3mm to allow it to be finished off with skim plaster ( information on plastering can be found in our skim plastering project ). Skim plastering is not necessary when filling chases on walls to be tiled after fitting pipes etc for concealed showers.
How to mix mortar and cement?
We mix the mortar at 3 soft sand to 1 sharp to 1 cement giving a strong mix which is still a little flexible. We then paint the chase with undiluted PVA adhesive to give the mortar the best chance of adhering to the conduit in the chase. The mortar is pushed well into the chase and the chase is filled. A trowel is then placed on both sides of the wall, straddling the chase and this is pulled upwards to cut off any surplus mortar.
What do you need to cut a chase line?
When the chase lines are cut you will need a hammer and bolster to chop out the middle but this is really easy as long as the chase blades are not set too far apart. You can also see a hammer and an assortment of chisels in the image. It is now possible to buy a chasing tool which fits onto your electric drill.
What is a chase tool?
The chasing tool seen in the image below is basically an angle grinder with two parallel blades. The depth of the blades can be set, a hoover hose plugged into the end and off you go.
How deep should vertical chases be?
The Simple Rules for Cutting Chases in Walls. Vertical chases should not be any deeper than one third of the total wall thickness. In a cavity wall, vertical chases should be no deeper than one third of the thickness of the skin they are being placed in. No chases, horizontal or vertical, should be made back to back.
How to keep chase lines straight?
You may also find it easier, in order to keep your chase line straight, to mark your lines on the wall with a pencil so that you can follow them.
How deep should horizontal chases be?
Horizontal chases indicated C on the above diagram should not be deeper than ⅙ of the wall thickness, or in a cavity wall ⅙ of the relevant leaf.
How thick is a hollow block?
For hollow or cellular blocks maintain a residual thickness of 15mm between the chase and the void unless otherwise recommended by the manufacturer.
What is a chase in a house?
A chase in home construction is a vertical space in a wall, which provides an area for pipes or wires to run through. Builders strategically place chases to ensure that cables run together. A chase may run up the wall from the basement to the attic or ...
What do professional builders use when cutting a chase in a wall?
An angle grinder contains two parallel cutting discs that have a certain depth cutting. The builder must first set the depth gauge before running the grinder up and down for a vertical chase or across the wall while making a horizontal chase.
How to hide cables?
When you run pipes or cables up or along a wall, the neatest way to conceal the cables is by burying them or chasing them in the wall surface. You have to follow several guidelines when you are chasing pipes or cables into walls: 1 You should avoid cutting a chase at an angle between the start and the finish of a wall. Instead, a chase cut-out should always be horizontal or vertical between the start and the wall’s finish. 2 If you are making a vertical chase, the chase should not be deeper than 1/3 of the wall’s thickness. If you have standard 3.9in (100mm) blocks or bricks, the chase should not be deeper than 1.3in (33mm). This depth is adequate for the installation of piping and cables, not allowing for the plaster coating. 3 If you are making a horizontal chase, the chase should not be deeper than 1/6 of the wall thickness. Therefore, if you have 3.9in (100mm) blocks or bricks, the horizontal chase depth should be 0.6in (16mm). This is sufficient to install the piping or the cables, not allowing for the plaster coating. 4 If you are cutting chases on the opposite sides of the walls, you must ensure that the chases are not in line. This means that the chases should not be back to back.
Why do builders chase cables?
Builders strategically place chases to ensure that cables run together. A chase may run up the wall from the basement to the attic or the upper part of your home. The rest of this article will help you learn more about a chase in construction, including: What you need to know about chases. How to chase cables and pipes into a wall.
How to chase cables into walls?
When you run pipes or cables up or along a wall, the neatest way to conceal the cables is by burying them or chasing them in the wall surface. You have to follow several guidelines when you are chasing pipes or cables into walls:
Why should cables be chased vertically?
By adhering to the requirements that cables and pipes should only be chased vertically or horizontally, you reduce the likelihood of the person driving a nail into the wires or pipes. Cutting a chase in a masonry wall weakens the wall structure. A horizontal cut weakens the wall structure more than a vertical cut.
How deep should a horizontal chase be?
If you are making a horizontal chase, the chase should not be deeper than 1/6 of the wall thickness. Therefore, if you have 3.9in (100mm) blocks or bricks, the horizontal chase depth should be 0.6in (16mm). This is sufficient to install the piping or the cables, not allowing for the plaster coating. If you are cutting chases on the opposite sides ...
