What is a plaster guard valve for?
The 'plaster guard' is just a piece of plastic that is attached to the valve to help set the depth inside the wall, dependent on the wall covering (drywall, cement board, tile, etc). Once set, the guard is removed and tossed. I've got Moen, but others do the same. Which is you buy the valve and pick one of several trim kits that fit the valve.
How do you install a plaster guard on a shower?
Pull down the wall around the shower, if you are removing the wall and re-tiling it at this point. Push the plaster guard onto the front of the shower valve body so the opening in the back of the plaster guard fits around the edge of the valve. Press the plaster guard forward until it is secure on the valve.
What is a plaster guard for a Delta shower faucet?
eHow may earn compensation through affiliate links in this story. When installing a Delta faucet, use a plastic plaster guard to prevent unwanted debris from entering the shower valve head. This round part is made just for your Delta faucet and is included with the faucet when you purchase it.
How do you measure for plaster guard wall tile?
Measure out from the bare studs next to the plaster guard with a tape measure to the width of your new wall, including the tile. Move the plaster guard until the front edge is flush with this measurement all the way around the plaster guard.
What is plaster ground used for?
A piece of wood used as a gage to control the thickness of a plaster coat placed on a wall; usually put around windows and doors and at the floor.
How deep do you set a Moen shower valve?
The center line of the supply and discharge piping should be a maximum of 2-3/16" (56mm) and a minimum of 1-7/16" (37mm) behind the finished wall surface.
How do you measure the depth of a shower valve?
0:1913:34How to Calculate the Correct Depth for a Shower Valve so it Finishes ...YouTubeStart of suggested clipEnd of suggested clipThe face of the plastic guard to the back so if you place your shower valve on the ground. And thenMoreThe face of the plastic guard to the back so if you place your shower valve on the ground. And then use a tape measure to measure from the ground to the face of that plastic guard.
How do you install a Delta shower valve?
0:006:28Delta Shower Valve Installation Tips for Beginners - YouTubeYouTubeStart of suggested clipEnd of suggested clipIgniter i highly recommend a flame protector. As well as h2o flux this is water soluble.MoreIgniter i highly recommend a flame protector. As well as h2o flux this is water soluble.
How much does it cost to install a new shower valve?
Average Cost of Shower Valve Replacement Most homeowners pay around $310 to have a plumber replace the stem and internal parts only. Replacing the entire shower valve however, cost an average of $540 installed.
What do you do when your shower valve is deep?
If your shower valve was installed too deep, you may need to purchase a shower valve extension. Signature Hardware carries valve extensions for some rough-ins, but not all. Professional installation should factor in the correct depth behind the wall, with any exterior wall covering included.
Can you replace a shower valve without removing tile?
If you are fortunate, your shower control wall will be adjacent to a wall that allows the plumber to access it by simply cutting the drywall on its opposite side. If this option is not available, the plumber will have to access the valve from the tiled side of the control wall.
What are the different types of shower valves?
In a nutshell, there are three different types of shower valves on the market: pressure balancing shower valve, thermostatic shower valve and diverter shower valve.
What is the proper height for a shower valve?
30-50 inchesThe average height for a shower valve is 30-50 inches above the floor, though this is a general range. For tub-shower units, the height can be just a few inches about the tub or directly on the tub as part of the faucet.
How much does a plumber charge to replace a shower valve?
Plumbers charge $100 to $300 for labor alone to replace a shower valve or $225 to $575 for the valve with installation. Replacing a shower valve takes 1.5 to 3 hours on average, depending on type and accessibility. Replacing a shower cartridge takes 30 minutes to 2 hours.
Are all Delta shower valves the same?
Although Delta valves are Universal, there is some confusion as they do offer several model numbers on their website. Typically the valve you want will be R10000-UNBX or R10000-UNWS. These are the most commonly used and work for 99% of people.
How do I identify my Delta shower faucet?
On the faucet, a model identification tag has been attached to most models manufactured since 2012. Look for the tag on one of the faucet's supply lines. Not all products have model identification on them. Shower faucets will show the Series embossed on the escutcheon plate below the handle.
How do you rough in a shower valve with PEX?
1:343:18How to install Shower Valve with PEX plumbing - YouTubeYouTubeStart of suggested clipEnd of suggested clipPipe i started off by cutting the top. First then i cut the bottom side of the valve. Step sevenMorePipe i started off by cutting the top. First then i cut the bottom side of the valve. Step seven take a deburring tool and deburr the inside edge of each pipe. Use some sandpaper.
How high should a tub shower valve be?
A height of 28 inches, or 2 feet 4 inches, is standard for valves in bathtub shower units. For shower stalls, install the valve at the standard height of 48 inches, or 4 feet. Install faucets at the same height as the valve, equidistant from the valve.
How do you install a Moen shower valve?
0:094:23Moen Shower Valve Installation Tips - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd bottom ports. So we place it about 16 inches off the tub deck. And we use 3/4 inch plywood. ToMoreAnd bottom ports. So we place it about 16 inches off the tub deck. And we use 3/4 inch plywood. To space out the tub. And get it set so we actually had to nail.
How far above the tub should the spout be?
Generally, your tub spout should be no lower than 4 inches above the rim of the tub. On the high side, it could be between 12 and 18 inches above the tub rim. If the spout is positioned too high, the stream might splash off the bottom of the tub, causing issues when you try to fill it.