Materials and Tools Needed to Remove a Toilet
- Adjustable wrench
- Empty bucket
- Sponge
- A mini-hacksaw
- Newspapers
- Old towel/rag
- Rubber gloves
- Putty knife
- Flathead screwdriver
How to unclog a toilet in 7 ways?
Method 2 Method 2 of 7: Making a Drain Cleaner
- Heat half a gallon of water. If the toilet tends to clog easily as the result of trying to flush too much waste, using a combination of hot water, ...
- Pour 1 cup baking soda and 2 cups vinegar into the toilet. The baking soda and vinegar create a chemical process that help to dissolve clogs.
- Pour the hot water into the bowl. ...
How to naturally clean a toilet?
Method 2 Method 2 of 2: Cleaning Your Toilet
- Sprinkle baking soda or borax into your toilet bowl. Lift the toilet seat, so that you can get the baking soda on all of the bowl’s surfaces.
- Drizzle vinegar into the bowl. A cup of white vinegar should be about the right amount to clean the bowl.
- Scrub your toilet bowl. ...
- Flush your toilet. ...
- Clean the exterior surfaces of your toilet. ...
How to install a new toilet correctly?
- Since there are many types of seats and lids, make sure to select a toilet seat that will fit your toilet model. ...
- Find the correct toilet seat size by measuring your new toilet if necessary.
- A specialty item such as a raised or heated toilet seat may have special installation requirements.
How to unclog a toilet every time?
Use 7 Unclogging Tricks
- Solution 1: A Toilet Plunger. A toilet plunger is a useful unclogging tool, so you probably already have it in your bathroom or garage.
- Solution 2: A Toilet Auger. ...
- Solution 3: Detergent and Hot Water. ...
- Solution 4: Vinegar and Baking Soda. ...
- Solution 5: Dish Soap. ...
- Solution 6: Commercial Cleaners. ...
- Solution 7: Epsom Salt. ...
What size wrench Do I need to remove a toilet?
Dual Socket Wrench for Toilet Installation, 9/16" x 1/2"
Can I remove a toilet by myself?
Removing a toilet is a relatively simple project that most DIYers can tackle either alone or with a helper. This guide will give you step-by-step instructions on how to remove a toilet. Safety Tip: Ceramic toilets are heavy, so lift with your legs, not your back, to avoid injury.
How do you remove an existing toilet?
3:354:32How to Remove a Toilet - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I'll show you just an easy way to get into a hard-to-reach. Area. So I just take a hacksaw bladeMoreSo I'll show you just an easy way to get into a hard-to-reach. Area. So I just take a hacksaw blade with a pair of leather gloves. And. I just get on the bottom of the nut. And we're just going to
What tools do I need to swap out inside toilet parts?
0:0014:13How to Fix a Running Toilet & Replace All Internal Toilet Tank PartsYouTubeStart of suggested clipEnd of suggested clipAnd I'm gonna show you how to do it. Alright so we're gonna replace.MoreAnd I'm gonna show you how to do it. Alright so we're gonna replace.
Can one person lift a toilet?
One person can sometimes lift a toilet, but it depends on the specific person and the toilet they're lifting. The average American man can lift about 155 pounds, and the average American woman can lift about 90 pounds. Toilets weigh about 96 pounds on average but can weigh anywhere from 70-115 lbs.
How hard is it to remove a toilet?
0:593:39How to Remove and Install a Toilet | The Home Depot - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou may need to cut them off with a hacksaw. Then gently rock the toilet back and forth until youMoreYou may need to cut them off with a hacksaw. Then gently rock the toilet back and forth until you can lift the old toilet. Free after removing the toilet remove the old closet bolts from the flange.
How long does it take to remove a toilet?
All things being considered, the time it takes to remove a toilet varies from 15 to 30 minutes, depending on the condition of the toilet parts and fittings. Below are the steps you'll need to follow to completely remove your old toilet from the floor and sewer pipe.
Do you have to replace the wax ring when you remove a toilet?
Whenever you remove a toilet for any reason, you will need to replace the wax ring seal between the toilet and the toilet flange (sometimes called a closet flange) attached to the floor. A wax seal is used because it resists mold and bacteria and retains its sealing ability after years of use.
What do I need to know when replacing a toilet?
0:161:50Things to Consider When Purchasing a New Toilet | The Home DepotYouTubeStart of suggested clipEnd of suggested clipBut smaller bathrooms may only accommodate around Bowl you might also consider a water saving toiletMoreBut smaller bathrooms may only accommodate around Bowl you might also consider a water saving toilet it only uses 1.28 gallons per flush now they'll save both water and money.
How often should you replace the toilet?
Most plumbers agree that an average toilet can last around 50 years. However, this is only when the toilet is well maintained and gently used. If it was improperly installed or frequently misused, it may not last as long.
How long does it take to remove a toilet?
All things being considered, the time it takes to remove a toilet varies from 15 to 30 minutes, depending on the condition of the toilet parts and fittings. Below are the steps you'll need to follow to completely remove your old toilet from the floor and sewer pipe.
Do you have to replace the wax ring when you remove a toilet?
Whenever you remove a toilet for any reason, you will need to replace the wax ring seal between the toilet and the toilet flange (sometimes called a closet flange) attached to the floor. A wax seal is used because it resists mold and bacteria and retains its sealing ability after years of use.
How long does it take a professional to install a toilet?
approximately 2 to 4 hoursIt takes approximately 2 to 4 hours for a plumber to install a toilet at a base rate of $65 per hour. If the plumber runs into any unexpected issues after the installation begins, it can raise labor costs by as much as $800.
What does Home Depot charge to install a toilet?
The Home Depot charges a standard fee of $99 for toilet installation. The charges are inclusive of the cost of the toilet, labor, and materials. However, the total cost will vary depending on the specific model of toilet you choose, as well as any additional features or services you request.
Measure for a New Toilet
Measure from your back wall to the closet bolts that secure the toilet to the floor. Be sure to measure from the wall and not from the baseboard. Also, measure to any nearby water supply lines on the floor. Some toilets have a wider base that might not fit next to a supply line on the floor.
Remove the Old Toilet
Once you have the new toilet, start removing the old one. When replacing a toilet, remember that toilets are heavy; it’s easier to remove the tank first and then the bowl. Here's how to remove a toilet:
Install the New Toilet
Once you've ensured the flange is in good shape, the next step is toilet installation. Here's how to install a toilet:
Step One: Gather Tools & Supplies for Removing a Toilet
Before beginning, ensure you have access to another toilet in case the process of removing the old toilet takes more time than you think it will or you run into some complications. Also, make arrangements for disposal of your old toilet, as some cities will not dispose of them on bulk trash pickup days.
Step Two: Turn Off The Water
Turn off the toilet's water supply, then flush the toilet several times to remove the standing water from the bowl and tank. Scoop out any water that remains, and sponge both the tank and the bowl dry. If you have a wet-dry shop vacuum, you can use it instead to remove any remaining water.
Step Three: Remove The Tank From The Toilet Bowl
Remove the tank from the bottom half of the toilet. This is where a ratchet or basin wrench will come in handy. Use one to remove the nuts from the mounting bolts holding the tank onto the bowl. Place the tank on the newspaper you laid down earlier.
Step Four: Remove The Nuts & Bolts Securing The Toilet to The Floor
Use an adjustable wrench to loosen and remove the nuts from the floor bolts at the base of the toilet. If there are trim caps over the bolts, remove those first. A hacksaw can be used to cut the bolts if they won't come loose with a wrench.
Step Five: Remove The Toilet From The Floor
Take out the utility knife and use it to free the toilet from the seal holding it to the floor. There is also a wax ring that seals the bottom of the toilet to the floor underneath the bowl. Rock the toilet back and forth until it's freed from its bonds. Lift the toilet and set it on its side on the newspaper.
Step Six: Clean and Cover The Toilet Flange
Scrape wax from the broken seal on the toilet flange (which is on the floor). Do this quickly, as the flange connects to the sewer pipe, which emits a gas. Once the wax is gone, use a stiff wire brush to clean the flange and stuff an old rag into the opening of the pipe.
What is the little pipe behind the toilet?
See that little pipe behind the toilet? That’s the water pipe and water supply.
What to use if plastic bolt is too tight?
Use a wrench if the plastic bolt is too tight.
Why do toilets stink?
Toilets are stinky for a reason: they’re connected to sewers! Once you remove a toilet, you don’t want those sewer gases coming back up into the house. So just be careful and gently place a towel or old rag in the hole. Use a towel that’s large enough to not fall down the sewer line!
How to get rid of waxy gunk on a ring?
Just use a small putty knife to scrape away the waxy gunk. You’ll be needing a new wax ring anyhow.
Can a strong man remove a toilet?
They think removing a toilet is a complex home maintenance project that only a strong man can do, but it’s not true. We women are just as capable. If you’re a homeowner, regardless of whether you’re a guy or a gal, everyone can learn how to replace a toilet, especially if the toilets in your house were like some of mine– ahem –avocado green!
Can you cut a screw off?
Yes… .cut them off. Don’t worry, it’s not hard, but you’ll need a little bit of strength. Typically you’ll want to use a hacksaw, which are just small hand-held saws that will allow you to cut through the screw. I didn’t have a hacksaw, per se, but I did use another small hand saw, which worked, thankfully!
Do you need to remove the bolt caps on a toilet?
If you’re removing the entire toilet ( and not just removing the back tank to paint behind the toilet), you’ll need to remove the bolt caps.
Disconnect the Toilet Connector
Whether you are replacing a leaking toilet or temporarily removing a toilet for bathroom renovations, the first step is to drain the water from it.
Remove the Toilet Tank
If you have a two-piece toilet, separate and remove the toilet tank. If you have a one-piece toilet, skip ahead to the next step that will tell you how to remove a toilet bowl. Here’s how to remove a toilet tank:
Unbolt the Toilet from the Floor
If necessary, pry off the trim caps on the floor bolts using a screwdriver.
Break the Toilet Seal
A toilet wax ring seals the bottom of the toilet bowl to the toilet flange on the floor. You’ll have to break this seal to remove the toilet bowl.
Remove the Old Wax Ring
Scrape away the old wax from the toilet flange and the bottom of the toilet with a paint scraper. Throw away the old wax into a bucket lined with a plastic bag.
Cover the Drain Hole & Dispose of the Old Toilet
Stuff a rag into the drain hole to prevent sewer gas from seeping into your home.
How to find model number of toilet?
To know the model number of a toilet, check inside the toilet tank on the wall next to the wall. The model number will be molded or just printed there.
How long does it take to remove a toilet tank?
Removing and replacing a toilet tank is a simple task that should not take you more than an hour. It is one of those tasks that you really don’t need to pay a plumber to do for you.
Why is my toilet leaking?
Whenever you notice your toilet leaking between the tank and the bowl, there are 3 things that might be the cause: A worn out tank to bowl gasket. A cracked flush valve. Loose toilet tank bolts.
What is the tank to bowl gasket?
The tank to bowl gasket (also called a spud washer ) is placed around the flush valve to ensure that there is no leakage between the tank and the bowl. The flush valve is the opening at the bottom of the tank through which water enters the bowl from the tank.
Why is water pooling in my toilet?
If you notice water pooling around the base of your toilet 3 things could be the cause: Toilet leaking between the tank and the the bowl. A leaking water supply line .
Why are toilet tanks placed above the toilet bowl?
Toilet tanks are strategically positioned above the toilet bowl in order to enable flushing via the natural force of gravity. Most toilet tanks are connected to the toilet bowl using two brass bolts. Some toilets however like Kohler toilets have a 3-bolt installation system.
What to use to cut nuts off a tank?
If even after that the bolts will just not come off, use a hacksaw blade to cut the nuts off, being careful not to cut the tank body. I say a hacksaw blade since a hacksaw will not fit in that tiny space.
How to make a toilet easier to install?
That means you have to cut off the protruding ends later with a hacksaw. But first connect the water line, flush the toilet a couple of times and check for leaks. Leaving the bolts uncut until you’ve done these final checks lets you easily remove and reset the toilet if you find any problems.
How to measure for a new toilet?
from the wall. But with a few models, that measurement is 10 in. or 14 in. To check the rough-in, just measure from the wall to the toilet’s hold-down bolts. If that measurement (plus the thickness of the baseboard) isn’t approximately 12 in., toilet shopping will be a bit harder. Most home centers carry only one or two 10-in. models and no 14-in. models. If you have to special-order a toilet, be prepared to spend much more. If there’s a door near the toilet, also measure how far the bowl protrudes from the wall. If you are replacing a toilet with a standard bowl with an “elongated” model, the door may not close. Read on to learn how to install a toilet.
What does a toilet bolt look like?
Some metal toilet bolts have a yellowish zinc coating that makes them look like brass. So check the label and make sure you’re getting brass bolts and nuts. They won’t rust away and they’re easier to cut off later. If you need to reanchor the toilet flange, buy stainless steel screws. They won’t corrode like steel or break off like brass while you’re driving them.
Why does my toilet rock?
If the flange is loose or damaged , the toilet will rock. And a rocking toilet will distort the wax ring and cause leaks. So be sure to scrape off the old wax ring and inspect the flange. Here are some solutions for broken, corroded or loose flanges.
How to fix rot under toilet flange?
The best solution depends on the extent of the rot. If the rot is only under the flange, use an ear-type repair ring. The ears let you drive screws into firm wood farther away from the flange. Before you install this kind of ring, hold it up to the drain horn on the underside of the toilet.
How to check rough in on a toilet?
To check the rough-in, just measure from the wall to the toilet’s hold-down bolts. If that measurement (plus the thickness of the baseboard) isn’t approximately 12 in., toilet shopping will be a bit harder. Most home centers carry only one or two 10-in. models and no 14-in. models.
Can you weld toilet bolts?
Don’t be surprised if the old nuts that hold the toilet in place won’t budge. Years of corrosion can weld them to their bolts. In that case, a hacksaw blade is the solution. You can buy a “close quarters” blade holder at home centers and hardware stores, or just wrap a bare blade with a rag or duct tape. Most toilet bolts and nuts are brass, so they’re easy to cut. If the bolt spins, grab it with locking pliers as you cut.