Enter the iAquaLink device number found on the door hanger or the device itself. To add the iAquaLink device to an account, you must be connected to the web through the same router the iAquaLink device is connected to. To download the App, go to iAquaLink.com and select
What part number do I use for Aqualink touch™?
If you have Aqualink Touch™. use Part Number IQ900. Aqualink All-Button Panel Aqualink OneTouch™ Panel
How do I connect iaqualink™ to the AquaLink automation system?
1 Wire iAquaLink™ to the AquaLink Automation system. 2 Start WiFi Setup Mode 1 2 4 Ensure all power to AquaLink is OFF, then remove the dead panel. Pass the iAquaLink cable through the low voltage raceway of the AquaLink. Reinstall the dead panel (and/or close doors if applicable) to ensure high-voltage areas are secured. Connect iAquaLink to the
What is Aqualink system?
AquaLink system is an expandable monitoring platform that enables the public utility companies to gain control over their water network in a simple and effective manner. The system is composed by battery powered field devices that are installed on the existing water district meter and a cloud based software that enables mobile online monitoring.
How do I know if my iaqualink is connected to WiFi?
Within 2 minutes, the yellow LED should stop blinking on the iAquaLink. When the green LED illuminates, the iAquaLink is connected. WiFi setup requires connecting via hotspot on your cell phone.
How do I pair Aqualink?
Attach the iAquaLink device to an internet connected PC or Mac® with a USB cable. Attach the iAquaLink device to an internet connected PC or Mac® with a USB cable. After programming the device with the network SSID & Key, replace the rubber gasket & cover.
Why wont my Aqualink connect?
If the process fails, the iAquaLink device will need to have its memory cleared by physically toggling the WiFi-Wired switch to Wired then back to WiFi. This will restart setup mode so you may attempt to connect it to your eero network again.
How do I connect my iAquaLink to a new router?
2:586:47iAquaLink 2.0 installation video - YouTubeYouTubeStart of suggested clipEnd of suggested clipAfter clearing the Wi-Fi settings. And with the switch in the Wi-Fi. Position press and release theMoreAfter clearing the Wi-Fi settings. And with the switch in the Wi-Fi. Position press and release the WPS. Button and wait for the small yellow LED next to the WPS button to begin blinking.
How do I change the WiFi on my Aqualink?
Inside the iAquaLink 2.0, toggle the WiFi - Wired switch to clear the Wi-Fi settings and put the iAquaLink in desired setup mode. 3. After clearing the WiFi settings and with the Wired/ WiFi switch set to WiFi, use a smartphone or WiFi enabled device and go to WiFi settings.
How do I reset my AquaLink?
How do I Reset a Jandy AquaLink System?Press the "Menu" button.Scroll to and highlight "System Setup" using the arrow keys. Press "Enter."Scroll to highlight "Clear Memory," then press "Enter." You have now reset your AquaLink system.
How do I fix iAquaLink waiting for connection?
0:402:09How To Fix "Waiting For Connection" For Jandy iAqualink AutomationYouTubeStart of suggested clipEnd of suggested clipLet us sit there for a second good five seconds or so and then go ahead and plug it back in and thenMoreLet us sit there for a second good five seconds or so and then go ahead and plug it back in and then from there you should be able to have. Your phone connects to your automation.
How do I use the iAquaLink app?
0:301:49How iAqualink Works With Your Pool - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd so to turn the waterfall on you go to devices. And you turn it on. And then the lights are alsoMoreAnd so to turn the waterfall on you go to devices. And you turn it on. And then the lights are also on this device area there's two lights there's the full light. And then there's also a spotlight.
How do I update iAquaLink firmware?
If your phone is set to allow updates to be automatically installed, the iAquaLink app will update to the new version automatically. If your phone is set to allow manual updates only, you can download the iAquaLink app at the iOS App or Google Play App stores.
How do I reset my iAquaLink password?
Enter your email address below and we'll send you a link where you can reset your password.
How do I connect my iAquaLink iq900 to WiFi?
Remove the gasket and cover. Locate the WiFi/WIRED switch and ensure it is in the WIRED position. Using standard Ethernet cable, connect one end of the cable into the connector on the device board. Connect the other end to the home network's router.
How do I remove a program from Jandy Aqualink?
0:571:56Jandy Aqualink schedule review and delete programming. - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can press a cancel button and basically the cancel button will be the way that you delete anyMoreYou can press a cancel button and basically the cancel button will be the way that you delete any schedules on there that you want to get rid of so your press the cancel button.
How do I change the time on my iAquaLink?
0:183:33I Aqualink Scheduling Equipment Run Times prproj - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll go to your home screen in the upper left-hand corner. You will see web click on web and thenMoreYou'll go to your home screen in the upper left-hand corner. You will see web click on web and then you will have to rotate.
What is eero router?
Unlike the familiar router-to-range extender network configuration, eero is a WiFi system that uses multiple access points to provide your home with fast, reliable coverage all on a single network. Range extenders can expand the reach of your existing wireless network.
How do I add iAqualink to Google home?
ConfigurationBrowse to your Home Assistant instance.In the sidebar click on Settings.From the configuration menu select: Devices & Services.In the bottom right, click on the Add Integration button.From the list, search and select “Jandy iAqualink”.Follow the instruction on screen to complete the set up.
Does Jandy pool have an app?
Free apps for Apple® and Android™ smartphones and tablets.
How long does it take for the yellow LED to stop blinking on an iAquaLink?
Within 2 minutes, the yellow LED should stop blinking on the iAquaLink. When the green LED illuminates, the iAquaLink is connected. WiFi Setup (iAquaLink 2.0 and greater): WiFi setup requires connecting via hotspot on your cell phone.
What is iAquaLink?
iAquaLink is a remote pool control system that allows you to control temperature, pumps, filters, lights etc for your pool and spa systems.
What happens if iAquaLink fails?
If the process fails, the iAquaLink device will need to have its memory cleared by physically toggling the WiFi-Wired switch to Wired then back to WiFi. This will restart setup mode so you may attempt to connect it to your eero network again.
What does it mean when the iAquaLink LED turns green?
If the iAquaLink LED turns green, it’s successfully connected to the WiFi. After clearing the WiFi settings, by physically toggling the WiFi-Wired switch to Wired then back to Wi-Fi, use a smartphone or WiFi enabled device to go to WiFi settings and connect to the network labeled "iAquaLink".
Does iAquaLink detect network strength?
iAquaLink will display the networks it detects, as well as signal strength. Select the network iAquaLink should use. If prompted for a password, enter the password for the home network (case sensitive). iAquaLink will disconnect from the smartphone at this point.
What is AquaLink system?
AquaLink system is an expandable monitoring platform that enables the public utility companies to gain control over their water network in a simple and effective manner.
Why is AquaLink important?
"AquaLink is ideal, because it allows insight into the system in places where the use of our Scada system is not possible. It is also useful as a support system to the existing system and for detecting water defects."
