why is my whirlpool duet dryer not starting

Why whirlpool duet dryer won’t start?

Full Answer

How to reset Whirlpool dryer?

How to reset Whirlpool dryer?

1. Turn the power off and wait at least 3 minutes before proceeding. First, turn the power off at the source.
2. Remove the power cord from the electrical outlet (If applicable) and unplug the appliance.
3. Wait 30 seconds. ...
4. Try to start your dryer once again. ...
5. Remove the load and unplug the dryer. ...
6. Remove the electrical connections and check them for damage. ...

More items...

How to repair a whirlpool dryer with a bad timer?

Use the flathead screwdriver to pry open a tab that holds a power source harness to the rear of the timer. Remove the timer knob, the two screws that hold the timer in place, and pull the old timer out. Replace the old timer with the new timer. Replace all other connectors and wire harnesses. After installing the new timer, replace the rear panel.

How to fix Whirlpool duet washer error code E01 F09?

Reasons Why Your Washer Displays the Error Code e01 f09

• Your washer’s drain hose may be bent and is not letting water out of your machine. ...
• Be sure that your washer’s drain hose height does not exceed 96 inches or risk having a washer that does not drain water properly.
• Clean your washer’s drain pump filter at the bottom front of your machine by removing objects and particles.

More items...

Why wont my Whirlpool dryer turn on?

Whirlpool Dryer Won’t Start – Troubleshoot and Diagnosis

• Incoming Power Problem. Sometimes, the problem isn’t with your dryer — it’s with your power. ...
• Door is Not Properly Latched. By pressing the Start button, you can begin a cycle on your dryer. ...
• Incorrect Whirlpool Dryer Settings. ...
• Faulty Dryer Start Switch. ...
• Blown Thermal Fuse. ...
• Bad Belt Switch. ...
• Defective Drive Motor. ...

Why won't my dryer start all of a sudden?

There are many things that could be the culprit for why your dryer won't start, including a bad thermal fuse; a failed start switch or door switch; a bad drive motor (what makes the dryer's drum turn and the blower wheel to work); a broken drive belt; a bad timer; a bad belt switch; a blown control board; or overall ...

When I press the start button on my dryer nothing happens?

If the dryer start switch does not have continuity when it is activated, it will need to be replaced. The door switch is located near the dryer door and is activated when the door is closed. If the door switch fails, the dryer won't start at all. Most door switches will make an audible click when they are activated.

How do I troubleshoot my Whirlpool Duet dryer?

Whirlpool Duet Dryer Will Not StartCheck the Circuits. Always check that the dryer is receiving the proper amount of 240v current. ... Check the Door Latch. The dryer will not start if the door latch is malfunctioning. ... Check the Thermal Fuse. Check to see if the Whirlpool dryer thermal fuse is blown. ... Check the Start Button.

How do you reset a Whirlpool Duet front load dryer?

General Reset Disconnect power to the dryer and wait 30 minutes then reconnect the power and resume normal use. If the problem continues or an error code returns, contact Whirlpool for advice or repair.

How do I know if my thermal fuse is blown?

Touch the left multimeter lead to the left side of the thermal fuse; touch the right multimeter lead to the right side of the fuse. Keep an eye on the multimeter needle; a needle that fails to move indicates a blown thermal fuse.

How do I know if my dryer start switch is bad?

As a safety feature, the dryer will not work with an open door. When the switch is broken, it is unable to tell the control panel the door is shut, so the dryer will not turn on. The only way to tell if the switch is faulty is to take it out of the dryer and test it with a multimeter.

Is Whirlpool Duet discontinued?

Whirlpool's earlier Duet (Sport) WFW8500S Washer has been discontinued and has been replaced with a line of Duet front load washers. While several Whirlpool front load washers of late (2016) tend to get poor ratings, there's one that stands out from the pack, because it has consistently met consumer expectations.

How do I start a Whirlpool Duet dryer?

0:071:07How to Start Using Your New Whirlpool Front Load Dryer - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the knob to select a cycle for your laundry load touch to activate any additional dryer optionsMoreTurn the knob to select a cycle for your laundry load touch to activate any additional dryer options. The model and serial number can be found on the inside edge of the machine.

Why does my dryer says sensing and wont start?

So, if it gets stuck in Sensing mode, that means that something has gone wrong with that process, and it can't start the drying cycle. At first glance, you may be dealing with a problem with the moisture sensor. Just like with previous problems, be sure to check and clean the moisture sensor and see if it works then.

Does unplugging a dryer reset it?

Resetting your dryer is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most), and then power it up again. That's it. That's all it takes to reset.

Where is the thermal fuse on a Whirlpool Duet dryer?

1:154:28Duet/ HE3 Dryer Thermal Fuse Replacement Part # WP3392519YouTubeStart of suggested clipEnd of suggested clipAnd at the top of the front panel remove the mounting screws located inside the door.MoreAnd at the top of the front panel remove the mounting screws located inside the door.

How do you put a Whirlpool dryer in diagnostic mode?

0:112:51Whirlpool, Maytag & Kenmore Dryer - Using Diagnostic Mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipEach button has two separate functions the first button that we pressed if we press it once willMoreEach button has two separate functions the first button that we pressed if we press it once will activate the UI buttons.

How do you test a dryer start switch?

1:382:42Dryer Not Starting? Three Terminal Switch Testing - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the normally open terminal by the letters n o to test the switch use a probe to touch the commonMoreAnd the normally open terminal by the letters n o to test the switch use a probe to touch the common terminal and the second probe to touch the normally open terminal now actuate the switch.

How do you fix a dryer that won't start?

0:026:183 Things To Check when your Dryer won't turn on or start - REPAIRYouTubeStart of suggested clipEnd of suggested clipAnd you don't hear anything like that it's almost a guarantee that that switch is bad so you'll haveMoreAnd you don't hear anything like that it's almost a guarantee that that switch is bad so you'll have to replace the switch. Alright the next tests are gonna require a multimeter.

How do you reset a clothes dryer?

1:092:47Dryer / washer not working. How to reset dryer / washer electronically.YouTubeStart of suggested clipEnd of suggested clipThat's it plug it back in and then. Once you plug it back in open. And close the door. Six timesMoreThat's it plug it back in and then. Once you plug it back in open. And close the door. Six times within 12 seconds. That's it I was in HH Greg pricing dryers. And that's all it took to fix it. It.

Where is the reset button on tumble dryer?

0:062:32What To Do If Your Tumble Dryer Is Not Heating Up - YouTubeYouTubeStart of suggested clipEnd of suggested clipSometimes it may be on the back panel. So you won't need to remove. It. To reset the heat on yourMoreSometimes it may be on the back panel. So you won't need to remove. It. To reset the heat on your tumble dryer press the red button in if it has tripped you should hear a click a.

How to tell if dryer is non functional?

A non-functional dryer motor has one big telltale sign: after pressing the ON button, the dryer’s LED panel will turn on, and you may even hear a slight humming. However, the drum will not spin.

What is the safety feature of a dryer?

One of the most important safety features in any dryer is its door sensor. This prevents you from opening the door while the dryer is working, and it will keep it from starting a cycle if the door is not properly locked.

What to do if your door doesn't work?

If there’s no visible culprit, try cleaning it anyway. If the door still doesn’t work, then you will need to replace the door switch. If you don’t have any electrical or appliance maintenance background, you should probably call a technician for this.

How to test thermal fuse?

To even test the thermal fuse, you will need to remove the drum and use a multimeter. Then, you (or a qualified technician) will need to replace the thermal fuse.

Can you leave clothes damp without notice?

Being left with damp clothes without any notice is bothersome, as you may need to improvise a clothesline for the next couple of days. However, this quick guide can help you diagnose the issue without waiting for a technician – and if you’re lucky enough to be dealing with a simple obstruction, then you should be able to fix it too.

Can you replace a belt without a motor?

This will depend on the type of damage you are dealing with: for example, if the internal belt is broken or out of place, you can replace the belt without dealing with the entire motor altogether.

Does a door switch stop dryer from working?

However, if the door switch malfunctions, it will prevent your dryer from working.

Why won't my Whirlpool dryer turn on?

As a safety precaution, a Whirlpool dryer doesn’t turn on if the door isn’t closed and latched. Even if the door appears closed, gently push to make sure it’s latched. Confirm that all clothing is in the dryer and that trapped items aren’t preventing the door from closing correctly.

How to check if Whirlpool dryer is working?

Sometimes a Whirlpool dryer not starting is more of a power issue than a dryer malfunction. To make sure your dryer is receiving adequate electricity here’s how to evaluate your incoming power: 1 Make sure the dryer is correctly plugged into the proper electrical outlet. 2 Check for tripped breakers or blown fuses. If needed, reset any tripped breakers and replace blown fuses. 3 Avoid using an extension cord. Most extension cords can’t safely transmit the electricity required to power a dryer.

Why does my dryer have a thermal fuse?

A dryer’s thermal fuse will trip to prevent the dryer from overheating, cutting power to the dryer. While a thermal fuse can malfunction over time, clogged dryer vents are a common trigger that blows the fuse. When assessing for a blown thermal fuse, check your dryer vents, cleaning them of any visible debris.

How to check for blown thermal fuse?

When assessing for a blown thermal fuse, check your dryer vents, cleaning them of any visible debris. If multimeter testing of the thermal fuse reveals a lack of continuity, it needs to be replaced.

How to check if dryer is receiving enough electricity?

To make sure your dryer is receiving adequate electricity here’s how to evaluate your incoming power: Make sure the dryer is correctly plugged into the proper electrical outlet. Check for tripped breakers or blown fuses. If needed, reset any tripped breakers and replace blown fuses. Avoid using an extension cord.

Why is my dryer not making a noise?

It could be because the dryer start switch is faulty. If the dryer doesn’t make any noise or motion when pressing the start button it’s likely the start switch is the problem. If multimeter testing confirms a lack of power to the switch it requires replacement. Image from Sears Parts Direct. #6.

Why won't my door latch?

If the door won’t latch, it’s possible that the latching mechanism is broken and requires professional replacement.

The Whirlpool Dryer Has No Power

When a dryer has no power, it is usually less about the dryer and more about the power source. Reset your circuit breakers and try to start the dryer again. Another reason the Whirlpool dryer has no power could be because the plug is faulty or not plugged in all the way.

The Whirlpool Dryer Touch Screen Not Working

If your Whirlpool dryer has a touch screen that is not working, there could be many issues here. These problems are mainly technological. Many dryers with a touch screen also have an app component, so there could be a simple issue with the app and the touch screen’s compatibility.

The Whirlpool Dryer Start Button Not Working

If everything is right with your Whirlpool dryer, but the start button is not working, you might have a broken start button. This can happen from time to time, but know that this issue is rare. If this happens, you will need to replace the wiring that controls the start buttons.

The Whirlpool Dryer Touch Screen Does Not Work

Touch screen malfunctioning is a possible outcome of any electronic appliance. The Whirlpool dryer touch screen is no different. Before getting into any repairs, be sure that you know how to work it, per the owner’s manual.

Conclusion

As you can see, there are so many issues that can arise with a dryer. Hopefully, you have picked up a few Whirlpool dryer troubleshooting tips for the next time you find yourself frustratingly staring at your dryer in the morning.

Incoming Power Problem

Sometimes, the problem isn’t with your dryer — it’s with your power. To make sure your Whirlpool dryer has adequate electricity to perform, check that it is receiving a consistent 240V from the wall socket. You can test this by plugging in a light bulb that uses 100 watts or less.

Door is Not Properly Latched

By pressing the Start button, you can begin a cycle on your dryer. Before pressing the button, you should always ensure the door has been closed and is properly latched. This helps to protect against injury and damage to your appliance.

Incorrect Whirlpool Dryer Settings

Before you start your dryer, check your settings to make sure you’ve selected the right cycle for your load. When the Wrinkle Reduction mode is turned on, the dryer will run intermittently instead of continuously to reduce wrinkles.

Faulty Dryer Start Switch

When you push the Start button on a dryer, It will send the signal to the start switch which in turn will send an electrical charge is sent to power the motor inside, which turns the drum. The motor spins the drum around and heats it up to a constant set temperature.

Blown Thermal Fuse

When a thermal fuse goes bad, your Whirlpool dryer won’t start. But if you know how to replace the thermal fuse, you can keep using your Whirlpool dryer and save yourself the cost of a new one.

Bad Belt Switch

A belt that makes the dryer tumble is called a drive belt. It stretches over the entire drum, going around and around and around. If it breaks, though, the machine might have power but will not tumble.

Defective Drive Motor

A dryer’s drive motor is the most important part of the unit and drives the tumbling mechanism that spins clothing in the dryer drum. It is an electric motor, but it is not like any other motor you may have seen before. The motor turns the belt that moves the tumbling action. If a dryer does not tumble, chances are the motor is gone.

Why won't my dryer start?

The dryer will not start if the door latch is malfunctioning. It may just need to be cleaned to remove lint and residue so that full contact is achieved or it may need to be replaced. Clean it by dipping a cotton swab in rubbing alcohol and cleaning all the contact points.

How to clean a washer that won't run?

First, try giving it a good cleaning. Use a cotton swab dipped in rubbing alcohol to clean the latch and any contact points. This will remove the lint, dirt, and product build-up that may be interfering with the electrical circuit.

Why is my washer accumulating water?

If the standing water is clear and clean, it is probably accumulating due to a failed inlet valve on the washer.

What causes water to back up in washer?

Be sure the washer's drain hose is not inserted too far down the standpipe. It should only be inserted about six to eight inches. A severe clog in the drainage line could also cause a back-up of drainage water that seeps back into the washer.

Is Whirlpool a Cabrio?

Whirlpool is a leading manufacturer of washers and dryers around the world including the Cabrio and the Du et models of washer and dryers. The Duet models are a popular line; however, as with any home appliance, there can be Duet washer and dryer problems and a need for repairs.

Why is my dryer not heating?

The duct (hose) could be clogged or bent. One or the other situation can cause the dryer to not heat properly. If the hose is both clogged and bent, this can eventually cause internal parts to burn out and need replacing. Clogged ventilation can cause excess moisture as well as ruining internal parts.

Why does my dryer keep clogging up?

A blocked lint screen can keep a dryer from heating up properly. If you use softener sheets, sometimes the softener can also clog the lint screen.

How to test a dryer heating element?

To test the heating element, place the multimeter probes on each of the heating element terminals.

How to test a dryer timer?

Be sure the dryer is unplugged. Turn the dryer timer knobs to a heating setting, such as 30 minutes and high heat. Place the probe on the timer’s Terminal A with the red wire.

How many volts does a dryer need?

Most dryers require 240 volts to operate, with two circuit breakers at 120 volts each. The extra voltage is needed to run the heating element of the dryer. While the dryer may turn on and the drum turn, if one breaker has tripped, the dryer will not heat.

Where are the wires on a heating element?

With the back panel, or front panel, removed, take a smartphone (digital) photo of the connected wires. These wires are located on the heating element housing. They are connected to the heating element terminals and the high-limit thermostat terminals just above. You’ll be glad to have this photo to refer to when reconnecting the wires!

What to do if simple practical checks do not solve heating problem?

If the simple practical checks do not solve the heating problem, the next step involves testing internal parts in the control panel and dryer. It is a simple process of discovering which part is causing the problem.

Why is my washer not starting?

The power cord can be faulty if the electrical outlet is operated, but the washer is not starting. That’s unusual, though. You should use a multimeter to test it for power to determine if the power cord is faulty. Replace the power cord if the power cord doesn’t get the work done.

Why is my washing machine not turning on?

When your washing machine is not turning on, please do check the power cord. You or someone may have disconnected it for any reason.

What is the filter on a Jacuzzi Duet?

Under the front kick plate is the filter on a Jacuzzi Duet. A cleaner for laundry absorbs lint that comes out of clothes when washing. There was a mistake. If the lint is not cleaned, the washing machine will be cycled back and laundry trapped.

What happens if my washing machine is overheated?

If your washing machine is overheated, there can be a chance of the fuse is damaged. If it is damaged, your washing machine is not going to be get started. To check, use a multimeter, and if you don’t see any continuity, nothing else can be done but to change it.

How long do washing machines last?

According to User Surveys, washing machines last around ten years on average. Here are some signs that the washer crosses the mark or has had some issues.

What to do if your washer is not getting started?

So if your washing machine is not getting started, do check if the door is closed correctly. The washer’s door lock may be electrically or mechanically failed. Check for damage to the door lock. Check whether the door lock has been broken or not appropriately secured.

Why is my washer's switch low?

The switch is most definitely low because the deck switch is pressing, and there is no energy supply to the washers. To test the turn, switch off the washing control and cut the wires from the deck switch. Test the multimeter consistency switch. Replace the lid switch if there is no consistency.