This Could Solve the Problem
- Whirlpool Ice Maker Isn’t Turned On. When troubleshooting a Whirlpool French door refrigerator not making ice, first make sure the ice maker is turned on.
- Improper Whirlpool Freezer Temperature. A Whirlpool refrigerator not making ice may come down to incorrect temperature settings. ...
- Whirlpool Ice Maker is Jammed. ...
- Water Supply Issues. ...
Why is my Whirlpool refrigerator too cold?
How to inspect a refrigerator’s air inlet damper or baffle:
- Unplug your refrigerator and locate the damper or baffle. ...
- Use caution when inspecting the baffle or damper to not damage the plastic & Styrofoam housing that the baffle or damper is encased in.
- If your model of has a temperature sensing bulb attached to this control make sure that the sensing bulb is in the correct position and not damaged.
What to do when your ice maker stops making ice?
What to Do When Your Ice Maker Stops Dropping Ice
- Reset the Ice Maker. The first and best troubleshooting step is to power-cycle the ice maker. ...
- Dump and Clean the Ice Bin. The next common possibility for why you’re not seeing ice down the chute is that it’s stuck in the bin.
- Check the Freezer Temperature. ...
- Unjam the Ice Tray. ...
- Inspect the Water Line. ...
- Replace the Water Filter. ...
How to reset a whirlpool refrigerator [Quick Guide]?
To reset your Whirlpool ice maker, you’ll need to do the following:
- Check which model of Whirlpool ice maker you own.
- If your model has a red reset button at the bottom, push this in and hold it for 10 seconds, before releasing.
- If there’s no reset button, carefully pull out the refrigerator from the wall and take the plug out.
- Wait 30 seconds, then plug your refrigerator back in again
How do you fix a whirlpool refrigerator?
Why is my TV suddenly saying no signal?
- Unplug the Fridge. Unplug the refrigerator from the electrical outlet. …
- Remove Access Panel. …
- Flush the Defrost Drain. …
- Clear the Drain. …
- Plug it Back In.
How do you reset a whirlpool ice maker?
1. Press the reset buttonLocate the reset button. The reset button is usually located at the bottom of the ice maker unit or in some cases at the top or on the bottom of the ice tray.Once located, press the button down for a few seconds until you hear a beep sound. ... Once reset, check if the problem has been solved.
How do I get my Whirlpool ice maker to work?
0:4911:05Refrigerator Ice Maker Not Working - Top 3 Reasons & Fixes - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen make sure the freezer is set below ten degrees Fahrenheit. Check your manual to verify theMoreThen make sure the freezer is set below ten degrees Fahrenheit. Check your manual to verify the temperature required for the icemaker to work usually. It's ten degrees Fahrenheit.
Why is my ice maker not working but water does?
Cause: There is also a possibility that the water filter for the ice maker is clogged. Fix: Locate and replace the water filter. Filters for ice makers are typically located inside the refrigerator (to keep them from freezing).
Why is my Whirlpool side by side ice maker not working?
Make sure the water supply is properly connected to a cold water supply and the water shutoff valve is fully opened. Check to make sure there are no kinks in the water supply line. A kink in the line can reduce water flow. Straighten the water source line to restore adequate water flow and pressure.
How do you jumpstart a whirlpool ice maker?
3:314:44IceMaker Not Working - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse your crescent wrench to get a nice tight grip on there you don't want to leave it loose becauseMoreUse your crescent wrench to get a nice tight grip on there you don't want to leave it loose because then I start leaking water and they'll be water all over the place.
Where is the reset button on my ice maker?
You can find the reset button at the bottom of the ice maker. Remove the ice tray to locate it. Remove the ice tray. The red button you see is the reset button.
Why does my fridge dispense water but not ice?
If the water inlet valve is defective, or if it has insufficient pressure, it won't allow water to flow through. As a result, the ice maker won't make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi.
How do I force my Whirlpool ice maker to cycle?
Look at the center of the Whirlpool icemaker to find the rotating arm that pushes the ice cubes out. Grab the plastic teeth on the arm, and gently pull them in a clockwise direction. You will hear a slight winding sound. The icemaker should start into its cycle.
How do I unclog my ice maker?
2:514:01Ice maker FROZEN over - how to FIX your freezer machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I needed to clean it out a bit and kind of get things moving again line up your ice maker withMoreSo I needed to clean it out a bit and kind of get things moving again line up your ice maker with the water pipe and the brackets that hold it in place reconnect. The power screw.
Is there a reset button on a Whirlpool refrigerator?
Press the door switches and the refrigerator temperature button three times within 10 seconds. After releasing the switches, there should be a letter "S" display in the freezer section and an "E" in the refrigerator's display. Press the fridge temp button once to get to the service moved.
1. Ice Maker Is OFF
For most models, the ice maker is turned ON with a small switch on the ice maker itself. It may have been turned OFF by mistake. Check to make sure the switch is in the ON position. If you still have problems getting ice or water, please keep reading below.
2. Check Whirlpool Ice Maker Shut-Off Arm
It’s normal for a Whirlpool refrigerator to have an ice maker with a switch. The switch is used to stop the ice maker from making ice once the bin is full. When the arm is in the down position, the ice maker will continue to work as normal. But if the ice in the bin has stopped the arm from going down, the ice maker will not continue to make ice.
3. Check Water Supply
The ice maker, the water dispenser, and even the fridge’s water supply pipe use the same water. It’s possible that there’s not enough water for any of them. Inside the refrigerator is where splits happen. The waterline supplying the Whirlpool ice maker might be clogged or kinked.
4. Faulty Water Inlet Valve
The water inlet valve is a key part of your ice maker. If this valve doesn’t work, the dispenser and ice maker won’t function. The water inlet valve requires at least 20 psi to function. If it’s defective, or if the pressure isn’t enough, the water won’t be able to flow through. As a result, the ice maker won’t function properly.
5. Freezer Temperature Issue
You need to keep your freezer in a specific temperature range for ice production. For example, it should be between 0-5°F. If the freezer is too cold, the ice will clump together and jam the ice maker. You need to keep your freezer in a specific temperature range for good ice production.
6. Jammed Ice Maker
Why won’t my refrigerator ice maker work? Recently, ice jams have been the most common reason for a refrigerator’s ice maker to stop working. This can happen when the metal fingers of the ejector’s arm try to grab new ice that is not yet fully frozen.
7. Faulty Water Filter
When there is a problem with the fridge filter, without enough water flowing to the ice maker, the production of ice will be halted or severely diminished. Make sure that water filter is not clogged and is currently installed as per manufacturer insutructions.
Ice Maker is OFF
Any Whirlpool freezer with a built-in ice maker will have a push button. This button turns the ice maker on and off, and this is usually located behind the front panel of your refrigerator. The wire arm attached to your ice maker should be pushed up to turn the ice maker OFF and lowered to turn it ON.
1. Freezer Temperature Issue
It’s best to maintain your ice maker between 0-5°F. As the temperature of the freezer goes up, your ice maker will either produce less ice or jam entirely. If you are consistently getting less than one tray per day, the temperature may be too high.
2. Jammed Ice Maker
An ice jam is one of the most common issues with refrigerator ice makers. Ice Jams happen when the metal fingers that eject ice cubes fail to grab new ice that’s not yet fully frozen. Water that doesn’t melt freezes on the metal fingers, creating an ice bridge that keeps new cubes from falling into the bin.
4. Defective Water Filter
When your ice machine is making noise and the ice cubes are jamming up, this could be a sign that you need to replace your water filter.
5. Check Water Inlet valve
An inlet water valve is responsible for supplying water to the refrigerator’s ice maker. If there isn’t enough water pressure entering the valve, it can’t open sufficiently to allow water to flow through. That means the ice maker will shut down and you’ll be without ice.
6. Faulty Icemaker Mold Thermostat
An ice maker mold thermostat is a small device installed in the ice maker of older refrigerator models. The thermostat regulates the temperature of the ice mold, or tray so that it can efficiently freeze water into cubes.
What happens if Whirlpool ice maker doesn't dispense ice?
You should hear the ice maker start to dispense ice. If the ice maker does not dispense ice, the door safety switch is probably faulty. A trained Whirlpool service technician is the best person to make this repair.
Why is my Whirlpool freezer not working?
If the freezer is warmer than 10 degrees Fahrenheit, the Whirlpool ice maker may not operate correctly. Turn the freezer thermostat down and wait 24 hours to give the system time to get to the new temperature. If your freezer doesn’t get any colder, you may have a problem with the thermostat or the condenser.
How much water pressure does a Whirlpool ice maker need?
Most Whirlpool refrigerator ice makers need at least 20PSI of water pressure to work properly. Low water pressure can affect your ice maker in several ways. The automatic inlet valve may not open. You may notice the ice molds not filling properly, resulting in small, misshapen ice cubes.
What does 18F mean on a Whirlpool refrigerator?
A Code 18F is an indication of an over-temperature condition in the refrigerator. Immediately check the electrical connection to your refrigerator. If the refrigerator is plugged in and there is power to the outlet, this is a serious condition. Contact a Whirlpool technician as soon as possible.
What does the ice maker switch do?
This switch prevents the ice maker from continuing to make ice when the bin is full. When the arm is in the fully down position, the ice maker operates normally. When the ice in the bin prevents the arm from lowering, the ice maker will not continue the ice making cycle.
What does the shut off arm do on an ice maker?
The shut-off arm may get pushed to the full up position and it will stay there. This position allows you to stop the icemaking cycle if necessary. The shut-off arm can engage in the top off position accidentally. Make sure that the shut-off arm on your ice maker is down.
Does Whirlpool refrigerator have ice maker?
Most new Whirlpool refrigerators equipped with ice makers also have an inline water filter. These filters need changing periodically or they will clog and stop the flow of water. Consult the user manual that came with your refrigerator to locate the filter.
Why won't my ice maker make ice?
If the water inlet valve is defective, or if it has insufficient pressure, it won’t allow water to flow through. As a result, the ice maker won’t make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi.
What happens if the door switch on a refrigerator fails?
The door switch turns off the ice and water dispenser when the refrigerator door is open. If the door switch fails, the dispenser will not turn on. To determine if the door switch is defective, use a multimeter to test it for continuity. If the door switch does not have continuity when activated, replace it.
How does an ice maker thermostat work?
The icemaker mold thermostat monitors the temperature of the ice mold (ice tray). Once the mold reaches the proper temperature, the icemaker ejects the ice cubes and refills the ice mold with water. If the mold thermostat is defective, the ice maker will stop making ice. To determine if the thermostat is defective, use a multimeter to test it for continuity. If the mold thermostat does not have continuity, replace it. (Note: If the ice maker is not cold enough, the mold thermostat contacts will ...
What happens at the end of an ice maker cycle?
At the end of the cycle, the icemaker module sends power to the water inlet valve to refill the tray with water. If the icemaker module is defective, the ice maker won’t make or dispense ice. First, depending on your model, make sure t...
How does an ice maker work?
The icemaker module is equipped with a motor that cycles the ice ejector arms or turns a tray to eject the cubes into the ice bucket. When the thermostat or sensor on the icemaker tray reaches about 15 degrees Fahrenheit, the motor cycles to release the ice cubes. At the end of the cycle, the icemaker module sends power to the water inlet valve to refill the tray with water. If the icemaker module is defective, the ice maker won’t make or dispense ice. First, depending on your model, make sure t...
How to tell if a thermostat is defective?
To determine if the thermostat is defective, use a multimeter to test it for continuity. If the mold thermostat does not have continuity, replace it. (Note: If the ice maker is not cold enough, the mold thermostat contacts will ... open. If the thermostat contacts are open, the ice maker will not make ice.
What temperature should an ice maker be?
The freezer temperature should be set between 0 and 5 degrees Fahrenheit (-18 to -15C) for the ice maker to work properly. If the freezer temperature is too high, ensure that the condenser coils are clear ...
