Full Answer
Why wont my pilot light stay lit?
Why Gas Fireplace Pilot Light Won’t Stay Lit and Their Solutions
- Check Your Pilot Flame A proper or healthy pilot flame will be much blue and sharp. ...
- Check the Thermocouple If your pilot flame is working, your thermocouple sensor may be damaged. ...
- Check the Burner The burner is under the pilot light and thermocouple. ...
- Drip Loop Excess moisture can enter your gas line, causing you to damage the pilot light. ...
Why is my furnace pilot not staying lit?
- Remove the pilot tube first
- Rub a piece of sandpaper on the tip of the pilot orifice
- Use a can of compressed air in the points where dirt is most likely to accumulate
- Use a thin, soft-bristled brush to reach every tiny nook of the orifice and burner
Why does the water heater pilot not stay lit?
Why Does Your Heater’s Pilot Light Keep Going Off?
- Obstructed Thermocouple. Most recently manufactured water heaters function with the aid of a thermocouple. ...
- Bent Thermocouple. Asides from being dirty and grimy, the thermocouple can also get bent or bent to the point where it starts to lose the heat signal from the ...
- Damaged Thermocouple. ...
- Dirty Pilot Tube. ...
- Flex Tube Defects. ...
- Main Control Valve. ...
Why your pilot light keeps going out?
What Makes Your Water Heater Pilot Light Go Out
- A Faulty Thermocouple Is The Reason Your Pilot Light Keeps Going Out. The thermocouple detects when your pilot light is burning. ...
- Strong Breeze Can Blow Out Pilot Light. It is not unlikely for excessive wind or a nearby draft to extinguish your pilot light flame. ...
- Kink in the Flex Tube. ...
- Filthy Pilot Light Opening Can Make Pilot Light Keeps Going Out. ...
Why won't my gas fireplace light stay on?
What color is the pilot light?
How to replace a thermocouple with a new one?
What is the pilot light problem in 2021?
How to find out if you need a new thermocouple?
What to do if pilot light is overflowing?
Why is my pilot light not working?
See 4 more
About this website
Why won't my pilot light stay on in my gas fireplace?
If the pilot light on your gas fireplace won't stay lit, a very likely culprit is a component called a thermocouple. A thermocouple is a safety device and is a component of the ignition system. Its purpose is to not allow the gas valve to open if the pilot light isn't lit.
How do I make my fireplace pilot light stay lit?
After years of use, your thermocouple may have a buildup of carbon deposit, which affects its ability to function. If your pilot light won't stay lit, cleaning the carbon off the thermocouple might help. The easiest way to tackle this home project is to abrade the rod with fine-grit sandpaper lightly.
Why does my pilot light go out on my fireplace?
Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don't hesitate to contact a professional.
Why does my gas fireplace go out after a few minutes?
It is a sensor that monitors the amount of oxygen that is in the room with the gas fireplace. If it detects that there is not enough oxygen present, its job is to turn off the fireplace. This is an important safety feature that protects you from carbon monoxide poisoning, which can be fatal.
Why do I have to keep relighting my pilot light?
If you have to relight your pilot light frequently, this points to mechanical issues – specifically, the thermocouple on the appliance. The thermocouple prevents gas from leaking into your home when the pilot light goes out. If faulty, a thermocouple can snuff out your pilot light.
How do I know if my thermocouple is bad on my gas fireplace?
Light the pilot and observe the quality and size of the flame. It should be mostly blue, burn steadily and be large enough to engulf the thermocouple probe. If it's yellow or orange, undersized and unsteady, the pilot tube is probably clogged, and it needs to be cleaned.
How do you clean a thermocouple on a fireplace?
Turn off the fireplace gas valve and remove the front panel from the fireplace. ... Use a can of compressed air to gently blow away any dust and dirt from the thermocouple.Wipe away any remaining dirt or soot on the thermocouple with a clean, dry cloth.
How do you clean a thermocouple?
Yes, you can clean a thermocouple, but the task must be done with a light touch. Remove the thermocouple from the process assembly, using a steel wool or emery cloth, lightly clean the tip removing any build up. Cleaning a thermocouple is not a fix for an issue, such as inaccurate readings.
Is it OK to run gas fireplace all day?
You can run a vented gas fireplace all day with little concern for anything other than gas usage.
How long can you run a gas fireplace continuously?
In short, you really shouldn't let a gas fireplace on for too long—specifically more than three hours at a time.
Should the pilot light always be on in a gas fireplace?
The pilot light needs to run continuously because, without it, the gas going into the fireplace would not have an ignition point. This would lead to fireplaces or entire gas fireplace inserts filling up with gas when they are turned on.
Is it safe if pilot light goes out?
A pilot light may need to be re-lit from time to time after being extinguished on purpose or by accident. If it is accidentally extinguished, there exists a danger that the gas used to keep the flame lit will continue to vent, possibly into the living space.
How do you stop the wind from blowing out the pilot on a gas fireplace?
A chimney balloon and a flue blocker are two fast and easy solutions. A chimney balloon is placed inside the chimney and is then inflated. It gets rid of the noise, keeps the cold air out and the warm air inside. A flue blocker works in the same way, except it's easier to install than the chimney balloon.
How do you fix a fireplace pilot?
0:001:08How to Fix Gas Fireplace Pilot Light That Won't Stay On - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet a can of compressed. Air or a pipe cleaner. And clean out this little hole spray some air downMoreGet a can of compressed. Air or a pipe cleaner. And clean out this little hole spray some air down to the main opening of the nozzle as well.
HOME FIX: Pilot light won't light on gas log fireplace - Courier & Press
EVANSVILLE, Ind. -- Brrr, it's cold out there. Let's just go inside and start a fire - but what's that? The pilot light on your gas fireplace is out and you can't get it going again.
What Causes A Pilot Light To Not Stay Lit?
Before I go into the reason you need to understand what pilot light is.
Verdict
There is nothing more disappointing that the gas fireplace does not light on a cold night. One of the main reasons for that is when the pilot light won’t light.
Why won't my gas fireplace light stay on?
1. Drip Loop . It’s possible that excess moisture may have gotten into your gas line, causing the pilot light to malfunction.
What color is the pilot light?
Flame Heat/Color. While the pilot light is ignited, use a flashlight to look into the pilot hole opening. Unless the flame is bright blue in color, it isn’t providing enough heat for the thermocouple to work properly. Similarly, make sure that the pilot flame is actually reaching the thermocouple.
How to replace a thermocouple with a new one?
If this is the case, remove your old thermocouple with a small wrench and take it to the hardware store with you so that you can correctly match up the length and nut size with the new one you’ll purchase. Each kit will come with varied nut adapters that can be matched up with your current size.
What is the pilot light problem in 2021?
Jason Pelmont. on May 24, 2021. Pilot light problems are common in gas appliances, such as water heaters, furnaces, and gas fireplaces. In most cases, the fix is something as simple and inexpensive as reigniting the pilot flame. However, if you find that your gas fireplace or similar appliance has a pilot light that won’t stay on even ...
How to find out if you need a new thermocouple?
To find out if you need a new one, turn the gas valve to pilot and then depress the override button. Hold it down for at least 30 seconds in order for the thermocouple to get warmed up.
What to do if pilot light is overflowing?
If you do notice it’s overflowing, use a pipe wrench to open the cap and drain out any liquid. Check out pipe wrenches on Amazon. 2. Thermocouple. The thermocouple is a small metal piece that crosses paths with the burning flame of the pilot light.
Why is my pilot light not working?
It’s possible that excess moisture may have gotten into your gas line, causing the pilot light to malfunction. To verify this, look at your gas meter and find the tee that has a section of capped pipe leading down from it.
What if the gas fireplace pilot light won’t stay lit?
You might find that you have an even bigger problem with your unit. What does it mean if your gas fireplace pilot light won’t stay lit? It could be an indicator of several different things, but it most commonly is caused by an issue with your thermocouple.
Why won't my gas fireplace stay lit?
Improper gas pressure. The thermocouple and thermopile are the two most common reasons why a gas fireplace won’t stay lit. However, there are other possibilities out there. Another common culprit is incorrect gas pressure. As the seasons pass, you may find that your gas pressure drops below where it needs to be.
Why does my gas fireplace not have a pilot light?
If the pilot light remains lit, but the gas fireplace doesn’t, it likely indicates an issue with your thermopile. This is another relatively small piece of your fireplace that converts heat to electricity, ultimately opening up the gas valve when you turn on the fireplace.
Why won't my pilot light stay lit?
What does it mean if your gas fireplace pilot light won’t stay lit? It could be an indicator of several different things, but it most commonly is caused by an issue with your thermocouple. A thermocouple. The thermocouple is a small metal sensor or rod that is situated directly in front of the pilot light.
Why is my gas fireplace not running?
Every appliance eventually reaches the end of its lifespan, and the components of your fireplace are no different. Issues with pieces of the ignition system , like your gas valve, can prevent your fireplace from running smoothly.
What to do if gas fireplace won't stay on?
However, if it continues and your gas fireplace still won’t stay on, it is always a good idea to have an experienced technician examine your fireplace. After all, messing with gas lines can be a dangerous business for someone who lacks technical expertise.
How many years has Michael Joseph been in the HVAC industry?
Michael Joseph has more than 20 years of hands-on experience as an avid home handyman and had 10 years in the construction industry, specifically in the field of HVAC.
Why won't my gas fireplace light stay on?
1. Drip Loop . It’s possible that excess moisture may have gotten into your gas line, causing the pilot light to malfunction.
What color is the pilot light?
Flame Heat/Color. While the pilot light is ignited, use a flashlight to look into the pilot hole opening. Unless the flame is bright blue in color, it isn’t providing enough heat for the thermocouple to work properly. Similarly, make sure that the pilot flame is actually reaching the thermocouple.
How to replace a thermocouple with a new one?
If this is the case, remove your old thermocouple with a small wrench and take it to the hardware store with you so that you can correctly match up the length and nut size with the new one you’ll purchase. Each kit will come with varied nut adapters that can be matched up with your current size.
What is the pilot light problem in 2021?
Jason Pelmont. on May 24, 2021. Pilot light problems are common in gas appliances, such as water heaters, furnaces, and gas fireplaces. In most cases, the fix is something as simple and inexpensive as reigniting the pilot flame. However, if you find that your gas fireplace or similar appliance has a pilot light that won’t stay on even ...
How to find out if you need a new thermocouple?
To find out if you need a new one, turn the gas valve to pilot and then depress the override button. Hold it down for at least 30 seconds in order for the thermocouple to get warmed up.
What to do if pilot light is overflowing?
If you do notice it’s overflowing, use a pipe wrench to open the cap and drain out any liquid. Check out pipe wrenches on Amazon. 2. Thermocouple. The thermocouple is a small metal piece that crosses paths with the burning flame of the pilot light.
Why is my pilot light not working?
It’s possible that excess moisture may have gotten into your gas line, causing the pilot light to malfunction. To verify this, look at your gas meter and find the tee that has a section of capped pipe leading down from it.
