How to Light a Bradford White Water Heater Pilot Light. Turn the Bradford White water heater off on the control panel; Let the water heater sit for 5 minutes to release gas from the system; Turn the control switch to pilot light mode; Press the red control button in for a few seconds and while pressing in, button every few seconds
How do you get the pilot light back on?
How Can I Restart My Pilot Light?Step 1: Turn off your furnace. ... Step 2: Locate your gas valve. ... Step 3: Hold down the red button. ... Step 4: Light the pilot light. ... Step 5: Let go of the button. ... Step 6: Turn your gas back on. ... Step 7: Turn your furnace back on.
How do you light a pilot light manually?
Relight the pilot light. Turn the knob to “Pilot,” and let gas to flow to the pilot. Light a lighter or match, then push in the reset button. Hold your flame to the pilot light's opening. Keep the reset switch depressed until the pilot light is burning steadily.
How do I light my electronic pilot light?
Turn the valve to the “pilot” position. Press and hold the reset button. If the reset button fails, ignite the lighter. Hold down the reset button and bring a grill lighter or long match to the pilot light valve until the pilot ignites.
How do you light a pilot light that won't light?
You need to turn the valve to the off position for at least three minutes. Once you have had the valve at off for a few minutes, switch it over to pilot setting. You will need a match that is lit. Hold it to the pilot opening and push the reset button on your pilot control.
Where is the pilot light button?
Near the bottom of your furnace is a switch that normally says "Pilot," "On" and "Off." Find this switch and turn it to the "Off" position. Wait at least five minutes. This is important because it gives the gas time to dissipate, which is necessary to avoid possibly starting a fire.
Can I light my own pilot?
Luckily, most homeowners are capable of relighting it on their own. Here are the steps you'll need to take to safely relight your furnace's pilot light. Warning! If you smell gas or suspect you have a gas leak, turn off the furnace and leave your home as soon as possible.
Can you manually light a gas water heater with electronic pilot?
They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system. If the pilot light is not lit: Attempt to re-light the pilot light, following the instructions posted on your water heater.
How do you light a Bradford White water heater?
0:574:22How to light Bradford White Hot Water Heater - YouTubeYouTubeStart of suggested clipEnd of suggested clipItself. So what we'll do is push in our pilot light this red button pushes right in when we pushMoreItself. So what we'll do is push in our pilot light this red button pushes right in when we push that in that's releasing gas from the gas. Line through the gas valve down into the gas chamber.
Can you manually light a gas furnace with electronic ignition?
If your furnace is equipped with an electronic igniter, you cannot light the furnace manually. However, you may be able to get the furnace working by turning off the igniter and resetting it. Find the paperwork for your particular furnace to locate the reset button or switch.
What happens if pilot light goes out?
Can a Pilot Light Outage Be Dangerous? The worry here is that when a pilot goes out, the gas valve that supplies the fuel for the pilot flame could still be pumping gas. This can mean a buildup of gas, and when the pilot is relit or relights itself it could result in a very serious explosion.
Why is my gas heater not igniting?
If your gas furnace initiates the start cycle but does not fire up, it's likely because of a faulty, damaged, or dirty ignitor/sensor. This is a very common furnace problem—you can try to clean the sensor and replace the ignitor.
Can you manually light a gas water heater?
Turn the water temperature dial to Low and the On/Off/Pilot dial to Pilot. Push the On/Off/Pilot dial downward with one hand while lighting the barbecue lighter with the other. Quickly hold the barbecue lighter over the end of the pipe by the burner. The flame should light instantly.
Can you light a pilot light without electricity?
If you have a gas fireplace with a vertical pilot, it will light during a power outage because it does not require electricity to start the pilot flame. Most gas fireplaces incorporate a self-generating millivolt system using a thermopile.
Can you manually light a gas fireplace with electronic ignition?
Some gas fireplaces come with electronic ignition wall switches, which are easy to use. Just turn the On button, and the pilot should startup; if not, you will have to light the pilot manually.
How do you light a push button pilot light?
Turn the valve to “Pilot.” Near the valve, you'll see a small button labeled “Reset.” Press this button while applying your lit match or butane fireplace lighter to the pilot light valve. Hold the flame steady until the pilot ignites, then release the button.
Why is my Bradford white water heater not lighting?
Common solutions for: Bradford White Water heater not lighting. Some water heaters use an igniter to ignite the gas. If the igniter fails, the burner will not light. To determine if the igniter is defective, first make sure the igniter is getting voltage.
What happens if the thermocouple does not detect a flame?
The thermocouple detects the pilot flame. If the thermocouple does not detect a flame, the ignition process will stall, and the burner will not light. Required Part. Water Heater Thermocouple. Enter model number to search for the required part specific to your product.
What is the purpose of a spark electrode on a water heater?
Some water heaters use a spark electrode to light the pilot flame. The spark electrode sends intermittent high-voltage sparks to light the pilot. If the spark electrode won’t produce sparks, it is likely defective. If the spark electrode is defective, replace it.
What happens if a water heater pilot is not lit?
The pilot ignites the water heater’s gas burner. If the pilot does not light, the water heater will not heat. Sometimes, carbon deposits can build up on the pilot and eventually create a restriction. If the pilot is restricted, try removing it and clearing it with a stiff brush and/or compressed air. If the pilot cannot be cleaned, replace it.
Why does my water heater not light?
The pressure switch closes when the proper airflow is achieved, signaling the control board to continue the ignition process. If the pressure switch is defective, the ignition process will stall , and the water heater will not light.