How do you turn on a Balboa hot tub pump?
Turn the pump on by pressing the power switch. If pressing the power switch on the pump doesn't work, you will need to order a new Balboa power switch. Open the jets in the hot tub. Closed jets will prevent the pump from being able to pump the water. Check that the height of the inlet pipe isn't higher than the water line.
What are the different modes of Balboa hot tub control?
Most Balboa hot tub control systems have three operating modes: standard, economy and sleep. These modes change at what time the hot tub heats, and therefore affect the overall power consumption. This is the most commonly-used mode, and in some cases it may be the only one available, depending on the configuration of your hot tub.
How do I install an electric hot tub?
Installation must be performed by a licensed electrician and all grounding connections must be properly installed. Test the ground fault circuit interrupter or residual current device before each use of the spa. Read the instruction manual. Adequate drainage must be provided if the equipment is to be installed in a pit.
How do you fill a hot tub with tap water?
A recommended method for filling your hot tub is through a garden hose equipped with a hose end spa pre-filter. This limits the amount of iron, lead or other impurities that may come standard in tap water. Hook up your hose to the filter area and fill the tub up to the water line as designated in your owner's manual.
How do you use a Balboa hot tub control?
1:464:58Using Balboa GS523 Control Panel On Zen Spas Hot Tubs ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress the mode button to set the beginning of filter cycle two and use the temperature buttons toMorePress the mode button to set the beginning of filter cycle two and use the temperature buttons to set the time.
How do you set up a hot tub for the first time?
How to Start a Hot Tub in 12 Easy StepsRinse and Drain. If you're a new hot tub owner, you're going to have to get used to the cleaning that comes with hot tub ownership. ... Turn off All Power. ... Clean the Empty Hot Tub. ... Install or Clean the Filter. ... Fill Your Hot Tub. ... Prime the Pump. ... Add the Start-Up Chemicals. ... Run the Pump.More items...•
How do I set my Balboa hot tub to standard mode?
Depending on system configuration, mode changing may not be available and will be locked in Standard Mode. Mode is changed by pressing “Temp,” then “Light”. Standard Mode maintains set temperature. will be displayed momentarily when you switch into Standard Mode.
How long does it take a Balboa hot tub to heat up?
It will take less time to heat if it is warmer outside. If you want your hot tub to be 100 degrees, it will take 4 hours to reach it's temperature. If you keep your hot tub cover on, you can shorten that time.
What chemicals should I put in my hot tub for the first time?
The chemicals you will need to start your hot tub include a pH increaser, pH decreaser, calcium hardness, a metal removal (if using water from rainwater tanks or bore) and a sanitiser. The chemicals have to go in a certain order for the process to work.
How soon after setting up a hot tub can you use it?
You may also want to wait a day to ensure that the chemicals in your water are balanced correctly and that any chlorine level is safe. Note that chlorine is not the only choice when it comes to a sanitizing chemical. Generally, you can expect to begin using your hot tub within 12 to 24 hours after filling.
What mode should I run my hot tub on?
Economy is a good setting for those who use the hot tub daily. The drop in temperature fluctuates during the year from minor or no temperature falls in the summer, to larger drops in the coldest part of winter.
What mode should hot tub be on?
Using Economy Mode Rather than heating the water consistently to maintain your set temperature, economy mode will only heat the water during your scheduled filtration times. Simply put, economy mode reduces your hot tub energy costs by running your heater less.
Why won't my Balboa hot tub heat up?
0:034:40HOT TUB Heater Not Working? 3 Common Problems | Swim UniversityYouTubeStart of suggested clipEnd of suggested clipMake sure the filter isn't clogged. And if you find debris clear it out and give it a good cleaning.MoreMake sure the filter isn't clogged. And if you find debris clear it out and give it a good cleaning. If the filter isn't the problem check the thermostat.
Is it cheaper to keep hot tub on all the time?
It's much more economical to maintain your tub's temperature rather than heating it from scratch each time. If you had to heat up your hot tub from cold each time you wanted to use it, this would have a dramatic impact on your hot tub running costs.
What temperature should you keep your hot tub when not in use?
So, what is the ideal hot tub temperature when not in use? A good rule of thumb to follow is always keeping your hot tub's temperature 5 degrees below what it usually is. This will save you time when you're reheating your tub, avoid consuming too much energy, and also protect your hot tub's internal system.
Should jets be on when heating hot tub?
Before covering your hot tub, make sure to turn on the jets as this will accelerate the pace of your hot tub's heating. By running the jets, you're allowing the heated water to be circulated and evenly distributed to all areas of the hot tub.
How much chlorine do I put in my first hot tub?
Setting Up A Hot Tub This can be done by adding 60g of chlorine granules per 1,500 litres of water to start the sanitation process and allow the level to drop to 3-5mg/l before using the hot tub.
What chemicals do you need for hot tub?
What chemicals do I need for my hot tub?Hot tub sanitiser – Kills bacteria in the hot tub water.pH increaser – used when pH in the water is too acidic.pH decreaser – used when pH levels in the water are too alkaline.Test strips – used to test sanitiser levels, pH levels and Total Alkalinity (TA).More items...•
Can I use my hot tub without chemicals?
It's not advisable to use a hot tub without any chemicals. Without chemicals, the hot tub becomes unsafe and can cause hot tub rash, and the water becomes host to harmful microorganisms. Over time, the contaminants in the water also have an adverse effect on the hot tub's equipment.
How do I put chemicals in my hot tub?
How to apply hot tub chemicals: a step by step guide.Remove the Hot Tub Cover. It is crucial that the cover is left open while applying chemicals. ... Turn on the Hot Tub, but Turn Off any Air Jets. Switch on your spa when applying. ... Use Test Strips. ... Pre-Measure Chemicals Safely. ... Apply Chemicals.
What is a spa pack?
Your Spa Pack is basically the brains, or motherboard of your spa. Its job is controlling all your spas components like your pump, heater, lights, and more. You may be thinking of changing your system due to a replacement board not been available anymore / discontinued or the spa manufacturer charging a very high price due to it being a licensed PCB / Pack.
Can I replace my spa pak?
Replacing your Spa Pak can be a quick and simple affair. In the worst case scenario, it may involve some light plumbing and wiring , and replacement of the top-side spa control, if purchased with your spa pack.
Step 1
Connect the power plug to an electrical outlet. Make sure there is electricity running to the outlet.
Step 2
Clear out the air tubes running from the pump to the hot tub. Any debris lodged within the tube should be removed with a pipe cleaner.
Step 3
Make sure the hose is running smoothly and isn't kinked or trapped under something.
Step 4
Turn the pump on by pressing the power switch. If pressing the power switch on the pump doesn't work, you will need to order a new Balboa power switch.
Step 1
Open the jets in the hot tub. Closed jets will prevent the pump from being able to pump the water.
Step 2
Check that the height of the inlet pipe isn't higher than the water line. The water line is where the water comes from and the inlet pipe connects the water line to the pump. The inlet pipe should never be above the height of the water line.
Step 4
Fill the hot tub with more water than you were previously using. A low water level will prevent the pump from working.
What are the operating modes on a Balboa hot tub?
Most Balboa hot tub control systems have three operating modes: Standard , Economy and Sleep. These modes affect the times at which the hot tub will heat, and therefore affect the overall power consumption. This is the most commonly-used mode, and in some cases it may be the only one available, depending on the configuration of your hot tub.
How to switch hot tub mode?
Keypads without a "Mode" button. Press "Temp", then "Light" to switch to the next mode. Repeat the process until you reach the mode that you're looking for.
Why set up a hot tub right?
Setting up your hot tub right the first time will prevent breakdowns further down the road due to a rushed installation. Here's some valuable steps for setting up a spa.
How long does it take to warm up a hot tub?
You are going to have to draw on another childhood lesson at this point: patience. It can take anywhere from seven to 24 hours before the water is thoroughly heated.
How to stop water seepage in spa?
This allows the water to flow through the pump and heater into your spa. To avoid water seepage around the spa, check to see that the drain valve is closed. Once you've taken safety precautions, it's time to get down and dirty by cleaning the interior of your hot tub with a clean towel and a mild, non-foaming, non-abrasive cleanser. ...
Can you hook up a hose to a water line?
Hook up your hose to the filter area and fill the tub up to the water line as designated in your owner's manual. Too little water and you could harm the pump or heater element.
Do you need to sanitize a hot tub?
Don't be fooled into thinking that your first time setup is complete after your water is filtered and hot. The water may look crystal clear, but in order for it to remain guarded against bacteria, you need to sanitize your hot tub. An effective spa sanitizer is necessary.
Can a tub heater leak if it's too little water?
Too little water and you could harm the pump or heater element. Once the tub is full, it's a good idea to check inside the electrical cabinet again and make sure no leakage is occurring around the fittings. Fittings can often jiggle loose during shipping, but a solid hand-tightening should do the trick.
What are the modes on a Balboa hot tub?
All Balboa hot tubs have energy saving modes (standard, economy and sleep) or ready & rest mode for the BP Series. Each mode has its benefits and at least 2 of the modes need to be used to give efficiency. The modes are explained below: Standard.
When does a hot tub use a heater?
The hot tub will only use the heater when the spa is in “filter mode” and the water has encountered a drop in temperature below the standard thermostat setting. By default filter modes are 2 hours in the morning and 2 hours in the evening, the rest of the time the hot tub will use the insulation to keep the spa warm and retain heat.
Why do hot tubs need to be left on?
Hot tubs need to be left on, it is a waste of power to frequently turn them on and off as this uses a lot of energy with the heater warming up the 1000’s of litres of water constantly. The hot tub is left on and by using the modes on the Balboa spa control system, the energy efficiency is improved & savings can be made.
What is the number to call for hot tub insulation?
The enhanced insulation on each hot tub @ Hot Tub Suppliers is clearly shown on our website & for further details please call us on 0116 2513378 or email us [email protected].
How cold does a hot tub heater go to sleep?
This works on the same basis as economy but when the hot tub filters , the heater will only operate when the drop in temperature is 10 degrees below the standard setting , so if your standard setting is 36 degrees, the heater when in sleep mode will only be activated when the temperature drops below 26 degrees.
