Biltwell bubble shields are a snap to install, if you start with the center snap and move outward. To clean your shield, use mild soapy water solution and a microfiber cloth to loosen bugs and road debris, then dry it with a second clean microfiber towel.
Full Answer
How to clean a motorcycle helmet?
1 fill a basin with warm water; 2 add detergent to the water: soap or hair shampoo; 3 take a soft brush or sponge; 4 put the helmet in the water; 5 and start washing it with soapy water and a sponge, carefully cleaning out all the dust and dirt; 6 let it dry or wipe with a soft, dry cloth. More ...
Why choose the Biltwell Lane splitter gloss black helmet?
The Biltwell Lane Splitter Gloss Black Helmet can be a go-to preference for its combination of fashion and capabilities. It is an abundance of new capabilities for motorbike riders who need consolation, airflow, and defense, additionally as exceptional styling.
How to clean a removable helmet liner and cheek pad?
An easy way to clean a removable helmet liner and cheek pads are to in a washing machine. Put the parts in a washing bag and use a mild detergent. Make sure to wash at a low temperature (less than 86 degrees Fahrenheit) and set a gentle setting to wash. A liner and cheek pads can also be washed in a sink or a tub.
What are the parts of a Biltwell helmet?
The shell, with a hand-tinted finish, also features a long-drawn-out polystyrene inner shield that adds style and luxury to the helmet. The Biltwell helmet comes with a hinged face shield. The hinged face shield is often very useful just in case you would like fresh air just lift the shield and let the breeze file through.
How do I clean my biltwell helmet liner?
Care: Never throw your helmets liner and cheek pads in the washer or dryer. Instead, carefully remove the pieces and hand wash them in the sink with mild soapy water—Palmolive and Dawn dishwashing liquids work great. Let the components air dry 24 hours before reinstalling them to avoid dampness or mildew.
How do you clean a biltwell visor?
0:442:34How To Clean Your Faceshield Without Special Cleaning SuppliesYouTubeStart of suggested clipEnd of suggested clipContact let the paper towel soak for a few minutes the moisture will not only soften the bugs butMoreContact let the paper towel soak for a few minutes the moisture will not only soften the bugs but float them off the surface of the visor.
What can I use to clean my helmet?
This is super simple. Just gently wash your helmet with mild soap and water. Any sink or bathtub will do, but we've even heard stories of riders taking their helmets into the shower with them!
How do I clean the inside of my full face helmet?
1:422:53How To Wash Your Motorcycle Helmet | MC GARAGE - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can actually wash the liner in place you just dunk the whole helmet in the soapy water just makeMoreYou can actually wash the liner in place you just dunk the whole helmet in the soapy water just make sure you rinse it really well and give it plenty of time to air dry.
How do you clean a biltwell bubble shield?
1:413:10How-To Install and Care for a Biltwell Bubble Shield - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnother maybe a lot of questions about is how to clean your bubble shield it's actually reallyMoreAnother maybe a lot of questions about is how to clean your bubble shield it's actually really simple all you need is some soap and water.
Can you use Windex on a helmet visor?
You should always clean your visor using the appropriate visor cleaner. The surface should be wet before you start wiping off the stain, or you risk scratching the surface. If you don't have a visor cleaner, you can also use regular glass cleaner, such as Windex.
Can I use alcohol to clean my helmet?
However, note that there are some things you should not use to clean your helmet because they can damage it, including: Solvent-based cleaners such as rubbing alcohol.
How often should you wash your helmet?
Weekly cleaning Apart from these deep cleansing routines that you must do at least once a month, make sure to clean your helmet once or twice every week. Use a wet cotton cloth to gently remove the dust from the visor. You can also purchase deodorizing sprays that you can use to keep your helmet smelling fresh.
Can you use glass cleaner on helmet?
Avoid glass cleaners or any product containing ammonia—they can lift the shield's anti-scratch coating. Pat dry, and be sure to store extra shields in a soft bag.
How do you clean a non removable helmet liner?
Helmets with non-removable liners can usually be freshened up with sprays and cleaners made for this purpose. Some are anti-microbial to kill mold and bacteria that grow in warm, dark, humid places and make the inside of your helmet smell like an old sock.
How do I get rid of the smell on my helmet?
So, with that in mind, here are 5 simple steps that you can do to clean the helmet ensure that it does not stink.Take the helmet apart. ... Soak the helmet in soap solution. ... Gently exfoliate the dirt and grime. ... Allowed helmet to dry naturally. ... Assemble the helmet. ... Deodorise- whenever you get a chance!
How do you clean the lining of a helmet?
You can either hand wash the lining in a bowl of warm water and use some baby shampoo (baby shampoo because it doesn't contain conditioner). Or, you can put it in the washing machine on the delicates (30 degree C) setting. But always read the manufacturers instructions before you do, just to be on the safe side.
What should you clean your visor with?
If you need to clean your visor or goggles, only use warm soapy water, or special products designed for it. Don't use abrasives or household cleaners.
Can you wash a visor in the washing machine?
Steps to Wash the Visor: Place the hat in the washing machine and wash as normal on gentle cycle. Remove the hat prior to the spin cycle as the force from the spinning can affect the shape of the hat. Rinse the hat in the sink. Gently press out the excess water with a towel.
How do you clean anti fog visors?
1:223:08Dirty Pinlock® Visor? Here's the Official Way to Clean it! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the wet cloth then you clean your visor with the same wet cloth. So you give that a clean withMoreAnd the wet cloth then you clean your visor with the same wet cloth. So you give that a clean with the same wet cloth inside and out make sure it's nice and clean. Obviously.
How do you remove stains from acrylic face shields?
Simple water is best, followed by diluted gentle dishwashing liquid or handsoap. Spray your water or dishwasher solution onto the acrylic surface, then blot or wipe the area dry with your clean (and not dusty) microfiber. Be gentle with the acrylic surface.
What are the cheek pads on a Biltwell helmet?
The stock cheek pads inside your Biltwell helmet were selected to provide comfort and security on a wide range of different-shaped faces across six different helmet sizes. That being said, these cheek pads were tested in a laboratory on a metal crash-test dummy—not living human heads with thick beards, big ears, fleshy cheeks, or other variables. If you did the fit test described above and your helmet feels too tight—or worse, too loose—we offer a wide range of accessory cheek pads in different thicknesses so you can customize your Biltwell helmet for a perfect fit.
How to wear a helmet?
Never wear a helmet that does not fit snugly and correctly on your head. Follow these steps to determine if your helmet provides the correct fit: 1 Grasp both loose neck straps, one in each hand. 2 Put the opening of the helmet on top of your head and pull the straps gently outward and down until your head is firmly and comfortably inside the helmet. Do not fasten the neck strap. 3 Stiffen the muscles in your neck to hold your head in a stationary position, eyes forward. 4 Grasp the helmet chin bar with both hands and move the helmet gently but forcefully from side to side. Repeat the same test, but in an up and down motion.
How thick are the cheek pads on a GRINGO helmet?
Find your helmet model and size on either chart (we’ll use a MEDIUM GRINGO S for this exercise). As the chart shows, the stock cheek pads on this helmet are 19mm thick.
What is the safety standard for Biltwell Lane Splitter?
Every Biltwell Lane Splitter—and every Gringo and Gringo S manufactured in 2019 or later—features construction and protection technologies that meet both US DOT and European ECE R22.05 safety standards. These technologies include but aren’t limited to the helmet’s injection-molded ABS outer shell, a multi-piece internal safety liner constructed ...
How to know if a helmet fits your head?
A correct-fitting helmet will move the skin on your cheeks side to side and the skin on your forehead up and down without rotating the helmet on your head. If you feel pressure or discomfort against any part of your skull, but especially against your forehead or temples, test fit a larger helmet. If the helmet moves around your head easily without moving the skin on your forehead and cheeks, test fit the next size down. A helmet that doesn’t fit your head properly will not provide adequate protection during an accident.
How to test for a swollen neck?
Stiffen the muscles in your neck to hold your head in a stationary position, eyes forward. Grasp the helmet chin bar with both hands and move the helmet gently but forcefully from side to side. Repeat the same test, but in an up and down motion.
How to check if a helmet fits?
Follow these steps to determine if your helmet provides the correct fit: Grasp both loose neck straps, one in each hand.
1. Remove Any Electronic Accessories From The Helmet
Take out any electronic accessories including speakers and Bluetooth devices that might be attached to the inside of the visor. After removing them, take a damp cloth and wipe down the interior lining until it looks clean.
2. Dismantle The Helmet
Take out all visor screws and gently lift up the visor from its hinges. Make a note of how many of each screw is used, their locations and sizes to ensure proper reassembly later. Then take off any other bolt or clasp that may be holding your helmet together.
3. Clean The Outer Shell Covering
Now immerse the entire outer shell of the helmet in water and use a toothbrush or similar scrubbing device on it for around 15 minutes until the shell looks clean again from outside. Use dishwashing soap to make this more efficient if necessary but make sure the helmet shell is fully dry before moving on to the next step.
4. Tidy Up The Vent Channels
Gently clean out any grit and dirt from the vent holes using a toothbrush or similar tool, these can get clogged with hair and dust after a while which may not look appealing. If you have air vents on top of your helmet, make sure they are pointing upwards for adequate drying later.
5. Prepare For Interior Lining Cleaning
If your helmet interior is made of leather, it’s a good time to clean that using leather cleaning solution, leave this for around 5-10 minutes and dry with a towel afterward. You can also use a small amount of mild dish soap if you have a cloth or sponge available.
6. Immerse The Inner Liner In The Water Tub
Turn the helmet upside down so the inner lining is facing downwards. Fill up a large water basin or tub with warm water and gently immerse the entire inner liner inside, allow to soak in the water for around 10 minutes then take out and squeeze all of the excess water from it by hand until damp but not dripping wet anymore.
7. Wash The Clothing With Clean Water
Apply dish soap or laundry detergent to the inner lining of your motorcycle helmet. Use a toothbrush or similar tool to remove any dirt and grime that has accumulated on it during your ride. Once clean, rinse with water thoroughly then allow ~24 hours for drying.
Why Biltwell?
Soon it developed an enviable reputation because of the superior quality helmets that it was designing and unleashing in the market. The passion and love for motorbikes is very important for the Biltwell Team and the world appreciates it.
Is Lanesplitter a full face helmet?
A lot of full face helmets tend to be big making you feel nauseous at the mere thought of having them on for more than a couple of hours, but the Lanesplitter is different. So think about it–a full face helmet that is light, comfortable, has a firm fit, and is not overly expensive. We are impressed!
Is Biltwell helmet affordable?
A lot of customers do agree that the helmet is not easily affordable, but upon using it and getting a feel of its flawlessness, they said that the helmet was worth every penny and reasonably priced compared to many others in the market that are less efficient but fall within the same price range. Another point to note is that Biltwell did not compromise on the design of the helmet just because it was providing you with a helmet packed with features–it looks great!
Is Biltwell helmet DOT compliant?
Today, Biltwell has launched several DOT compliant helmets – be it full face or the three-fourth version that they initially started out with. It did not just build a stellar reputation by manufacturing sub-standard helmets–these helmets are some of the best available in the market.
How to clean a helmet liner?
An easy way to clean a removable helmet liner and cheek pads are to in a washing machine. Put the parts in a washing bag and use a mild detergent. Make sure to wash at a low temperature (less than 86 degrees Fahrenheit) and set a gentle setting to wash. A liner and cheek pads can also be washed in a sink or a tub.
How to get rid of dirt on helmet?
Soak a microfiber rag in warm water and use it all over the helmet. This will help loosen the dried up grime and insects. Let the wet cloth rest on the helmet for some time, as this will reduce the effort to remove the stuck-on dirt.
What is a full face helmet?
Full face and ¾ helmets have cheek pads inside of the helmet that rests against your cheeks. They are removable for cleaning. They are an added comfort feature intended to provide extra protection.
How many degrees does a motorcycle helmet visor have?
They are usually removable to clean or to swap out for another shield/visor. A motorcycle helmet visor usually provides a vision of 105 degrees. (The average person’s peripheral vision is about 90 degrees at each side).
Why is it important to wear a helmet?
A helmet’s Importance. The main purpose of a helmet is to protect the motorcyclist’s head in an accident. The head and brain are most vulnerable to injury in a motorcycle accident. Motorcyclists wearing helmets increase their chance of survival and recovery significantly over non-helmet wearers.
What is the outer shell of a helmet made of?
The outer shell is the outermost part of the helmet you see from the outside. It is usually made up of Kevlar, carbon fiber, and a combination of other plastics .#N#Its function is to protect your head in the event of an impact and keep foreign objects from penetrating the helmet.#N#Impact Absorbing Liner:#N#The liner is on the inside of the outer shell. It is usually made up of EPS, a form of polystyrene foam. Its purpose is to absorb the shock and dissipate energy during an impact.
Why do motorcyclists need a helmet?
To prevent such situations, wearing a helmet is necessary for a motorcyclist. Furthermore, a quiet helmet cuts down on wind noise roaring in your ears, on wind blast on your face and eyes, and deflects bugs and other objects flying through the air. A helmet looks robust and sturdy but should be handled delicately.
How to clean a helmet interior?
The easiest way to clean your helmet interior is to remove the liner and padding (if possible) and place it in a mesh garment bag. Then place it in your washing machine on the most delicate setting and wash with Woolite. Take it out of the machine immediately and let it air dry.
How to clean a motorcycle helmet?
To keep your helmet clean and not allow the dead bugs to harden and possibly etch themselves into your helmet’s finish, we recommend a quick post-ride cleaning . Often, just wetting a paper towel or microfiber cloth and laying it over the goo for a minute or two will be enough to soften up the debris. Then use a cloth/towel or two to gently scrub the surface until it shines. Stubborn crust can be removed by using a motorcycle-specific cleaner, like our current favorite S100 Detail & Wax. Do not use harsh chemicals. Window cleaner and dish soap are too strong for use on your helmet. Window cleaner, in particular, can dry out and accelerate the aging of your helmet’s surface. If you ask the people who maintain helmets for a living, the Arai and Shoei support at racing series, they’ll tell you that they just use water and elbow grease.
Why do you need a mesh bag for helmets?
The mesh garment bag helps to protect the parts. Do not put the liner in the dryer or expose it to other sources of heat. If you can’t remove the helmet liner, you can still clean the interior, but it will take significantly longer to dry. You’ll need clean cloths and a bowl of mild soapy warm water.
How to dry a helmet?
To dry the helmet interior, press the liner and padding with clean dry cloths until no more water comes out. Then place the helmet in a place with good air circulation to dry. Helmet manufacturers recommend that you not leave them in the sun to accelerate the process.
How to get soap out of helmet padding?
Don’t be afraid to really saturate the liner with clean wet rags as the final step. Using lots of warm, mildly soapy water, scrub the interior liner of your helmet. Then rinse until soap suds no longer bubble up from the liner when it is compressed.
How to speed up a helmet?
If you want to speed it up, use a fan to blow air across it. Never use a hair dryer because it could damage the glues holding the liner and padding together. You can wash your helmet’s liner in mild soap in your washing machine on its most delicate cycle. The mesh garment bag helps to protect the parts.
Why is a visor treated with soap?
The visor gets special treatment because some manufacturers use special coatings on the interior to prevent fogging, and cleaning this with harsh chemicals could render it useless . With warm weather and mild soap on your fingers wet the visor and then clean it with the lightest touch possible.
